Changeset 615 in xtideuniversalbios for trunk/XTIDE_Universal_BIOS

Timestamp:

Aug 7, 2021, 9:02:29 AM (3 years ago)

Author:

Tomi Tilli

Message:

• COMMAND_IDLE was not enough to disable standby timer from 1,8" Toshiba HDD. Apparently idle mode is the default mode. Added COMMAND_STAND_BY and that does what COMMAND_IDLE was supposed to do. Without COMMAND_STAND_BY the 1,8" Toshiba HDD experienced some random pauses (=>retry/abort... prompts) especially with Freedos 1.3RC4 but MS-DOS 7.10 (Win98) was mostly OK.
• Added FEATURE_ENABLE_ADVANCED_POWER_MANAGEMENT command to set drive to maximum performance mode when standby timer is disabled. This feature needs a bit more work. See TODO comments in sources.

Location:

trunk/XTIDE_Universal_BIOS

Files:

• Inc/DeviceIDE.inc (modified) (1 diff)
• Inc/IdeRegisters.inc (modified) (2 diffs)
• Src/Handlers/Int13h/AH23h_HFeatures.asm (modified) (1 diff)
• Src/Handlers/Int13h/AH9h_HInit.asm (modified) (1 diff)

trunk/XTIDE_Universal_BIOS/Inc/DeviceIDE.inc

@@ -31 +31 @@
 TIMEOUT_MAXIMUM         EQU     255         ; We would actually want 31 seconds here but I don't think there are so slow drives
 
+
+; ATA specs say that in standby mode time to respond could be as long as 30 seconds
+; Note that some low-power drives (like Toshiba 1,8" HDD) have power management enabled by default
+; TODO: It might be better to define timeouts in IDEVARS (in ROMVARS) or in DPT. Having even a single bit in DPT means
+; we could adjust timeouts on runtime when enabling or disabling power management.
 %ifdef MODULE_POWER_MANAGEMENT
     TIMEOUT_BSY         EQU     TIMEOUT_MOTOR_STARTUP

trunk/XTIDE_Universal_BIOS/Inc/IdeRegisters.inc

@@ -97 +97 @@
 COMMAND_IDENTIFY_DEVICE                 EQU     0ECh
 COMMAND_SET_FEATURES                    EQU     0EFh
+COMMAND_STAND_BY                        EQU     0E2h
 COMMAND_IDLE                            EQU     0E3h
 
@@ -103 +104 @@
 FEATURE_ENABLE_8BIT_PIO_TRANSFER_MODE   EQU     01h     ; CFA feature set only
 FEATURE_ENABLE_WRITE_CACHE              EQU     02h
+FEATURE_ENABLE_ADVANCED_POWER_MANAGEMENT    EQU 05h
 FEATURE_DISABLE_8BIT_PIO_TRANSFER_MODE  EQU     81h     ; CFA feature set only
 FEATURE_DISABLE_WRITE_CACHE             EQU     82h     ; Can also be used to flush cache
+FEATURE_DISABLE_ADVANCED_POWER_MANAGEMENT   EQU 85h     ; Might not be supported even if FEATURE_ENABLE_ADVANCED_POWER_MANAGEMENT is
 FEATURE_SET_TRANSFER_MODE               EQU     03h     ; Transfer mode goes to the Sector Count Register
     PIO_DEFAULT_MODE                    EQU     0h

trunk/XTIDE_Universal_BIOS/Src/Handlers/Int13h/AH23h_HFeatures.asm

@@ -101 +101 @@
 %endif ; MODULE_8BIT_IDE_ADVANCED
 %endif ; MODULE_8BIT_IDE
+
+
+;--------------------------------------------------------------------
+; Enable/disable advanced power management command can be used to scale
+; power consumption and performance. Drive supporting Enable APM might not
+; support Disable AMP so we set the drive to max performance if stand by
+; timer value is 0 (idle/standby disabled)
+;
+;
+; AH23h_EnableOrDisableAdvancedPowerManagement
+;   Parameters:
+;       DL:     Stand By timer value (0=disable APM)
+;       DS:DI:  Ptr to DPT (in RAMVARS segment)
+;       SS:BP:  Ptr to IDEPACK
+;   Returns:
+;       AH:     Int 13h return status
+;       CF:     0 if successful, 1 if error
+;   Corrupts registers:
+;       AL, BX, CX, DX, SI
+;--------------------------------------------------------------------
+%ifdef MODULE_POWER_MANAGEMENT
+AH23h_EnableOrDisableAdvancedPowerManagement:
+    mov     si, FEATURE_ENABLE_ADVANCED_POWER_MANAGEMENT
+    test    dl, dl
+    jnz     SHORT .EnablePowerSave
+    dec     dx
+    dec     dx      ; DL = FEh = Maximum performance
+    jmp     AH23h_SetControllerFeatures
+    
+; TODO: We should add power management level to IDEVARS to be adjustable with xtidecfg
+.EnablePowerSave:
+    mov     dl, 0BFh    ; For Toshiba 1.8" HDD: 80h...BFh = Mode 1
+    jmp     AH23h_SetControllerFeatures
+%endif ; %ifdef MODULE_POWER_MANAGEMENT

trunk/XTIDE_Universal_BIOS/Src/Handlers/Int13h/AH9h_HInit.asm

@@ -200 +200 @@
     jz      SHORT .NoPowerManagementSupport
 
+    ; Do we need to disable APM?
+;TODO: We should check APM feature set flag from ATA ID word 83. The above
+;FLGH_DPT_POWER_MANAGEMENT_SUPPORTED is from ATA ID word 82
+    mov     dl, [cs:ROMVARS.bIdleTimeout]
+    push    dx
+    push    dx
+    call    AH23h_EnableOrDisableAdvancedPowerManagement
+
+    ; COMMAND_IDLE is not enough for Toshiba 1,8" HDD since idle mode is the default mode
+    ; COMMAND_STAND_BY seemed to do the trick
+    pop     dx
+    mov     al, COMMAND_STAND_BY
+    mov     bx, TIMEOUT_AND_STATUS_TO_WAIT(TIMEOUT_BSY, FLG_STATUS_BSY)
+    call    Idepack_StoreNonExtParametersAndIssueCommandFromAL
+    STORE_ERROR_FLAG_TO_DPT     FLG_INITERROR_FAILED_TO_INITIALIZE_STANDBY_TIMER
+
+    pop     dx
     mov     al, COMMAND_IDLE
-    mov     dl, [cs:ROMVARS.bIdleTimeout]
     mov     bx, TIMEOUT_AND_STATUS_TO_WAIT(TIMEOUT_BSY, FLG_STATUS_BSY)
     call    Idepack_StoreNonExtParametersAndIssueCommandFromAL