Changeset 493 in xtideuniversalbios for trunk/XTIDE_Universal_BIOS/makefile


Ignore:
Timestamp:
Dec 21, 2012, 8:44:25 AM (12 years ago)
Author:
gregli@…
google:author:
gregli@hotmail.com
Message:

Separated MODULE_8BIT_IDE into the basic part used by XTIDE rev 1 and rev 2 which is PIO based, and MODULE_8BIT_IDE_ADVANCED for JRIDE and XTCF support which requires memory mapping and/or DMA. This allows for creating an 8KB image with boot menu support (but no hotkeys) for the XTIDE rev 1. Cleaned up how we reset the drive translation information, ensuring it is properly set between boot attempt on a primary and secondary drive - as a result we clean it when needed, rather than trying to always keep it clean. Also fixed translation bugs in int13h.asm where I had previously missed converting some MODULE_HOTKEYS into MODULE_DRIVEXLATE.

File:
1 edited

Legend:

Unmodified
Added
Removed
  • trunk/XTIDE_Universal_BIOS/makefile

    r491 r493  
    1616# Following modules can be included or excluded:                                                   #
    1717# MODULE_8BIT_IDE             Support for 8-BIT IDE cards like XTIDE                               #
     18# MODULE_8BIT_IDE_ADVANCED    Support for memory mapped and DMA based cards like JRIDE and XTCF    #
    1819# MODULE_ADVANCED_ATA         Native support for some VLB IDE controllers                          #
    1920# MODULE_BOOT_MENU            Boot Menu for selection of drive to boot from                        #
     
    9697#################################################################
    9798DEFINES_COMMON = MODULE_STRINGS_COMPRESSED MODULE_HOTKEYS MODULE_EBIOS MODULE_FEATURE_SETS RESERVE_DIAGNOSTIC_CYLINDER
    98 DEFINES_COMMON_LARGE = MODULE_BOOT_MENU MODULE_8BIT_IDE
     99DEFINES_COMMON_LARGE = MODULE_BOOT_MENU MODULE_8BIT_IDE MODULE_8BIT_IDE_ADVANCED
    99100
    100101DEFINES_XT = $(DEFINES_COMMON) ELIMINATE_CGA_SNOW MODULE_8BIT_IDE MODULE_SERIAL MODULE_SERIAL_FLOPPY
    101102DEFINES_XTPLUS = $(DEFINES_COMMON) $(DEFINES_XT) USE_186
    102 DEFINES_AT = $(DEFINES_COMMON) USE_AT USE_286 USE_UNDOC_INTEL RELOCATE_INT13H_STACK MODULE_IRQ MODULE_SERIAL MODULE_SERIAL_FLOPPY MODULE_ADVANCED_ATA
     103DEFINES_AT = $(DEFINES_COMMON) USE_AT USE_286 USE_UNDOC_INTEL RELOCATE_INT13H_STACK MODULE_IRQ MODULE_SERIAL MODULE_SERIAL_FLOPPY MODULE_ADVANCED_ATA 
    103104
    104105DEFINES_XT_LARGE = $(DEFINES_XT) $(DEFINES_COMMON_LARGE)
     
    109110DEFINES_386_8K = $(DEFINES_AT) USE_386
    110111
    111 DEFINES_ALL_FEATURES = MODULE_8BIT_IDE MODULE_ADVANCED_ATA MODULE_BOOT_MENU MODULE_EBIOS MODULE_HOTKEYS MODULE_IRQ MODULE_SERIAL MODULE_SERIAL_FLOPPY MODULE_STRINGS_COMPRESSED MODULE_FEATURE_SETS
     112DEFINES_ALL_FEATURES = MODULE_8BIT_IDE MODULE_ADVANCED_ATA MODULE_BOOT_MENU MODULE_EBIOS MODULE_HOTKEYS MODULE_IRQ MODULE_SERIAL MODULE_SERIAL_FLOPPY MODULE_STRINGS_COMPRESSED MODULE_FEATURE_SETS MODULE_8BIT_IDE_ADVANCED
    112113
    113114
Note: See TracChangeset for help on using the changeset viewer.