Changeset 592 in xtideuniversalbios for trunk/XTIDE_Universal_BIOS/Src/Handlers/Int13h

Timestamp:

Jun 25, 2018, 10:29:27 PM (7 years ago)

Author:

Krister Nordvall

Message:

Changes:

• The problem with NASM in the previous revision (r591) has been fixed.
• The colors used by the boot menu and hotkey bar can now be customized by selecting one of a number of pre-defined color themes. Suggestions for additional themes are more than welcome!
• Large builds are now 10 KB. Small builds are still 8 KB with the exception of the Tiny build which is now 4 KB. In other words, builds are now as small as possible to make it easier to combine them with other BIOSes.
• Added code to the library to improve drive error handling. XTIDECFG can now handle "Drive Not Ready" errors.
• Fixed a couple of potential bugs in AtaID.asm (AtaID_GetMaxPioModeToAXandMinCycleTimeToCX); 1) ATA1.bPioMode was treated as a WORD variable. 2) ATA2.bPIOSupp was assumed to be non-zero which would result in PIO mode 3 being returned if the assumption was wrong.
• Made the same changes in the equivalent function used by BIOSDRVS (DisplayPioModeInformationUsingAtaInfoFromDSBX in AtaInfo.asm).
• Fixed a bug from r587 in PDC20x30.asm in PDC20x30_GetMaxPioModeToALandMinPioCycleTimeToBX.
• Fixed a bug from r523 in XTIDECFG where Auto Configure would only set the IRQ on one IDE interface on AT-builds.
• XTIDECFG will now restore the default settings for the "Serial port virtual device" when reselecting it in the list of device types. This makes it behave consistently for all device types.
• The eAAM macro is now used regardless if USE_UNDOC_INTEL is defined or not because it is apparently supported on all processors including the NEC V20/V30 CPUs.
• Renamed the EXCLUDE_FROM_XTIDE_UNIVERSAL_BIOS define to EXCLUDE_FROM_XUB.
• Added a define to exclude unused library code from BIOSDRVS (EXCLUDE_FROM_BIOSDRVS). This makes it a lot smaller than in previous revisions.
• All unnecessary CLD-instructions are now under a new define 'CLD_NEEDED' which is only enabled for the BIOS. It is disabled for XTIDECFG and BIOSDRVS but can be enabled if needed by adding this define to the respective makefile. This change was made because these unnecessary instructions are wasteful and should never be needed. In fact, they only serve to hide bugs (in other peoples code) which I strongly believe should be avoided. I recommend people making their own BIOSes from source to not use this define as it's extremely unlikely to be needed.
• Updated the copyright info in SerDrive and changed an URL to point to the new site.
• Updated the copyright info and version number in BIOSDRVS.
• Updated the copyright info in XTIDECFG.
• Optimizations in general.

Location:

trunk/XTIDE_Universal_BIOS/Src/Handlers/Int13h

Files:

• AH0h_HReset.asm (modified) (2 diffs)
• AH1Eh_XTCF.asm (modified) (1 diff)
• EBIOS/AH41h_CheckIfExtensionsPresent.asm (modified) (3 diffs)
• Tools/Address.asm (modified) (1 diff)

trunk/XTIDE_Universal_BIOS/Src/Handlers/Int13h/AH0h_HReset.asm

@@ -126 +126 @@
     mov     cx, NUMBER_OF_IDEVARS
 
-.loop:
+.Loop:
     call    FindDPT_MasterOrSingleForIdevarsOffsetInDL
     jc      SHORT .ControllerNotAvailable
@@ -162 +162 @@
 .ControllerNotAvailable:
     add     dl, IDEVARS_size                            ; move Idevars pointer forward
-    loop    .loop
+    loop    .Loop
     ret

trunk/XTIDE_Universal_BIOS/Src/Handlers/Int13h/AH1Eh_XTCF.asm

@@ -121 +121 @@
     ;
     ; Also note that some machines, noteably the Olivetti M24 (also known as
-    ; the AT&T PC6300 and Xerox 6060), have hardware errors in the BIU logic,
-    ; resulting in reversed byte ordering.  Therefore, XTCF_8BIT_PIO_MODE is
-    ; the default transfer mode for best system compatibility.
+    ; the AT&T PC6300 or Xerox 6060 or Logabax Persona 1600), have hardware errors
+    ; in the BIU logic, resulting in reversed byte ordering.  Therefore,
+    ; XTCF_8BIT_PIO_MODE is the default transfer mode for best system compatibility.
 
 

trunk/XTIDE_Universal_BIOS/Src/Handlers/Int13h/EBIOS/AH41h_CheckIfExtensionsPresent.asm

@@ -46 +46 @@
 
     mov     BYTE [bp+IDEPACK.intpack+INTPACK.ah], EBIOS_VERSION
-    mov     WORD [bp+IDEPACK.intpack+INTPACK.bx], 0AA55h
+    not     WORD [bp+IDEPACK.intpack+INTPACK.bx]    ; 55AAh = AA55h
 
 %ifdef MODULE_COMPATIBLE_TABLES
@@ -75 +75 @@
 ;--------------------------------------------------------------------
 AH41h_GetSupportBitsToCX:
+%ifdef USE_AT   ; Always in Full mode
+%ifndef MODULE_8BIT_IDE OR MODULE_SERIAL
+    mov     cx, ENHANCED_DRIVE_ACCESS_SUPPORT | ENHANCED_DISK_DRIVE_SUPPORT
+%else
+    mov     cx, ENHANCED_DRIVE_ACCESS_SUPPORT
+    cmp     BYTE [di+DPT_ATA.bDevice], DEVICE_8BIT_ATA
+    jae     SHORT .DoNotSetEDDflag
+    or      cl, ENHANCED_DISK_DRIVE_SUPPORT
+%endif
+%else ; ~USE_AT
     mov     cx, ENHANCED_DRIVE_ACCESS_SUPPORT
 
     ; DPTE needs buffer from RAM so do not return it in lite mode
-%ifndef USE_AT
     test    BYTE [cs:ROMVARS.wFlags], FLG_ROMVARS_FULLMODE
     jz      SHORT .DoNotSetEDDflag
-%endif
 
 %ifdef MODULE_8BIT_IDE OR MODULE_SERIAL
@@ -91 +99 @@
 
     or      cl, ENHANCED_DISK_DRIVE_SUPPORT ; AH=48h returns DPTE
+%endif ; USE_AT
 .DoNotSetEDDflag:
     ret

trunk/XTIDE_Universal_BIOS/Src/Handlers/Int13h/Tools/Address.asm

@@ -110 +110 @@
     and     al, MASKL_DPT_TRANSLATEMODE
 
-;;; 0: ADDRESSING_MODE_NORMAL
+;;; 0: TRANSLATEMODE_NORMAL
     jz      SHORT DoNotConvertLCHS
 
-;;; 1: ADDRESSING_MODE_LARGE
+;;; 1: TRANSLATEMODE_LARGE
     test    al, FLGL_DPT_ASSISTED_LBA
     jz      SHORT ConvertLargeModeLCHStoPCHS
 
-;;; 2: ADDRESSING_MODE_ASSISTED_LBA
+;;; 2: TRANSLATEMODE_ASSISTED_LBA
     ; Fall to ConvertAssistedLBAModeLCHStoLBARegisterValues