Changeset 498 in xtideuniversalbios for trunk/XTIDE_Universal_BIOS_Configurator_v2

Timestamp:

Jan 4, 2013, 7:22:04 PM (12 years ago)

Author:

aitotat@…

google:author:

aitotat@gmail.com

Message:

Changes to Configurator v2:

• Auto Configure now detects XT-IDE rev 1 and rev 2 correctly.

File:

• trunk/XTIDE_Universal_BIOS_Configurator_v2/Src/IdeAutodetect.asm (modified) (3 diffs)

trunk/XTIDE_Universal_BIOS_Configurator_v2/Src/IdeAutodetect.asm

@@ -76 +76 @@
     jnc     SHORT .IdeDeviceFound
 
-    ; Try to detect 8-bit XT-IDE rev 1
+    ; Try to detect 8-bit XT-IDE rev 1 or rev 2.
+    ; Note that A0<->A3 address swaps Status Register and Alternative
+    ; Status Register addresses. That is why we need another step
+    ; to check is this XT-IDE rev 1 or rev 2.
     shr     cx, 1
     call    DetectIdeDeviceFromPortDXwithStatusRegOffsetsInBLandCX
-    mov     al, DEVICE_8BIT_XTIDE_REV1
-    jnc     SHORT .IdeDeviceFound
-
-    ; Try to detect 8-bit XT-IDE rev 2 or modded rev 1
-    ; This doesn't actually work since Status Register and Alternative
-    ; Status Register swap place!!!
-    mov     bl, 1110b   ; STATUS_REGISTER_in with A0 and A3 swapped
-    mov     cl, 0111b
-    call    DetectIdeDeviceFromPortDXwithStatusRegOffsetsInBLandCX
-    mov     al, DEVICE_8BIT_XTIDE_REV2
+    jc      SHORT .SkipRestOfDetection  ; No XT-IDE rev 1 or rev 2 found
+
+    ; Now we can be sure that we have XT-IDE rev 1 or rev 2.
+    ; Rev 2 swaps address lines A0 and A3 thus LBA Low Register
+    ; moves from offset 3h to offset Ah. There is no Register at
+    ; offset Ah so if we can write to it and read back, then we
+    ; must have XT-IDE rev 2 or modded rev 1.
+    push    dx
+    add     dx, BYTE 0Ah                ; LBA Low Register for XT-IDE rev 2
+    mov     al, DEVICE_8BIT_XTIDE_REV2  ; Our test byte
+    out     dx, al                      ; Output our test byte
+    JMP_DELAY
+    in      al, dx                      ; Read back
+    pop     dx
+    cmp     al, DEVICE_8BIT_XTIDE_REV2
+    je      SHORT .IdeDeviceFound
+    mov     al, DEVICE_8BIT_XTIDE_REV1  ; We must have rev 1
+    clc
 .IdeDeviceFound:
     ret
@@ -193 +204 @@
 .rgwIdeBasePorts:
     dw      IDE_PORT_TO_START_DETECTION     ; Must be first
-    ; JR-IDE/ISA (Memory Segment Addresses)
-    dw      0C000h
-    dw      0C400h
-    dw      0C800h
-    dw      0CC00h
-    dw      0D000h
-    dw      0D400h
-    dw      0D800h
-    dw      0DC00h
+    ; Standard IDE
+    dw      DEVICE_ATA_PRIMARY_PORT
+    dw      DEVICE_ATA_SECONDARY_PORT
+    dw      DEVICE_ATA_TERTIARY_PORT
+    dw      DEVICE_ATA_QUATERNARY_PORT
     ; 8-bit Devices
     dw      200h
@@ -219 +226 @@
     dw      3C0h
     dw      3E0h
-    ; Standard IDE
-    dw      DEVICE_ATA_PRIMARY_PORT
-    dw      DEVICE_ATA_SECONDARY_PORT
-    dw      DEVICE_ATA_TERTIARY_PORT
+    ; JR-IDE/ISA (Memory Segment Addresses)
+    dw      0C000h
+    dw      0C400h
+    dw      0C800h
+    dw      0CC00h
+    dw      0D000h
+    dw      0D400h
+    dw      0D800h
 .wLastIdePort:
-    dw      DEVICE_ATA_QUATERNARY_PORT
+    dw      0DC00h