Context Navigation

Strings.asm@ 595

Visit:

Last change on this file since 595 was 592, checked in by Krister Nordvall, 6 years ago

Changes:

The problem with NASM in the previous revision (r591) has been fixed.
The colors used by the boot menu and hotkey bar can now be customized by selecting one of a number of pre-defined color themes. Suggestions for additional themes are more than welcome!
Large builds are now 10 KB. Small builds are still 8 KB with the exception of the Tiny build which is now 4 KB. In other words, builds are now as small as possible to make it easier to combine them with other BIOSes.
Added code to the library to improve drive error handling. XTIDECFG can now handle "Drive Not Ready" errors.
Fixed a couple of potential bugs in AtaID.asm (AtaID_GetMaxPioModeToAXandMinCycleTimeToCX); 1) ATA1.bPioMode was treated as a WORD variable. 2) ATA2.bPIOSupp was assumed to be non-zero which would result in PIO mode 3 being returned if the assumption was wrong.
Made the same changes in the equivalent function used by BIOSDRVS (DisplayPioModeInformationUsingAtaInfoFromDSBX in AtaInfo.asm).
Fixed a bug from r587 in PDC20x30.asm in PDC20x30_GetMaxPioModeToALandMinPioCycleTimeToBX.
Fixed a bug from r523 in XTIDECFG where Auto Configure would only set the IRQ on one IDE interface on AT-builds.
XTIDECFG will now restore the default settings for the "Serial port virtual device" when reselecting it in the list of device types. This makes it behave consistently for all device types.
The eAAM macro is now used regardless if USE_UNDOC_INTEL is defined or not because it is apparently supported on all processors including the NEC V20/V30 CPUs.
Renamed the EXCLUDE_FROM_XTIDE_UNIVERSAL_BIOS define to EXCLUDE_FROM_XUB.
Added a define to exclude unused library code from BIOSDRVS (EXCLUDE_FROM_BIOSDRVS). This makes it a lot smaller than in previous revisions.
All unnecessary CLD-instructions are now under a new define 'CLD_NEEDED' which is only enabled for the BIOS. It is disabled for XTIDECFG and BIOSDRVS but can be enabled if needed by adding this define to the respective makefile. This change was made because these unnecessary instructions are wasteful and should never be needed. In fact, they only serve to hide bugs (in other peoples code) which I strongly believe should be avoided. I recommend people making their own BIOSes from source to not use this define as it's extremely unlikely to be needed.
Updated the copyright info in SerDrive and changed an URL to point to the new site.
Updated the copyright info and version number in BIOSDRVS.
Updated the copyright info in XTIDECFG.
Optimizations in general.

File size: 29.9 KB

Line
1	; Project name : XTIDE Universal BIOS Configurator v2
2	; Description : All strings.
3
4	;
5	; XTIDE Universal BIOS and Associated Tools
6	; Copyright (C) 2009-2010 by Tomi Tilli, 2011-2013 by XTIDE Universal BIOS Team.
7	;
8	; This program is free software; you can redistribute it and/or modify
9	; it under the terms of the GNU General Public License as published by
10	; the Free Software Foundation; either version 2 of the License, or
11	; (at your option) any later version.
12	;
13	; This program is distributed in the hope that it will be useful,
14	; but WITHOUT ANY WARRANTY; without even the implied warranty of
15	; MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16	; GNU General Public License for more details.
17	; Visit http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
18	;
19
20	; Section containing initialized data
21	SECTION .data
22
23	; DOS version check
24	g_s$NotMinimumDosVersion: db LF,"This program requires DOS version 2 or higher.",LF,"$"
25
26	; Menu title
27	g_szProgramTitle: db "Configuration and Flashing program for XTIDE Universal BIOS v2.0.0.",LF,CR,NULL
28	g_szXtideUniversalBiosSignature: db FLASH_SIGNATURE,NULL
29	g_szBiosIsNotLoaded: db "BIOS is not loaded!",NULL
30	g_szEEPROM: db "EEPROM",NULL
31	g_szSourceAndTypeSeparator: db " : ",NULL
32	g_szUnidentified: db "Unidentified",NULL
33	g_szUnsaved: db " ",SINGLE_LEFT_HORIZONTAL_TO_VERTICAL,"Unsaved",SINGLE_RIGHT_HORIZONTAL_TO_VERTICAL,NULL
34
35	; Item formatting
36	g_szFormatItemWithoutValue: db "%c%s",NULL
37	g_szFormatItemNameWithValue: db "%25s%-10S",NULL
38
39
40	g_szNo: db "No",NULL
41	g_szMultichoiceBooleanFlag: db "No",LF
42	g_szYes: db "Yes",NULL
43
44	; General Yes/No response type dialog messages
45	g_szDlgExitToDos: db "Exit to DOS?",NULL
46	g_szDlgSaveChanges: db "Do you want to save changes to XTIDE Universal BIOS image file?",NULL
47	g_szDlgDriveNotReady: db "Drive not ready! Retry?",NULL
48
49	; Generic dialog strings
50	g_szNotificationDialog: db "Notification.",NULL
51	g_szErrorDialog: db "Error!",NULL
52	g_szGenericDialogInfo: db "Press ENTER or ESC to close dialog.",NULL
53
54	; Flashing related strings
55	g_szFlashTitle: db "Flashing EEPROM, please wait.",NULL
56	g_szErrEepromTooSmall: db "Image is too large for selected EEPROM type!",NULL
57	g_szErrEepromPolling: db "Timeout when polling EEPROM.",LF
58	db "EEPROM was not flashed properly!",NULL
59	g_szErrEepromVerify: db "EEPROM did not return the same byte that was written.",LF
60	db "EEPROM was not flashed properly!",NULL
61	g_szPCFlashSuccessful: db "EEPROM was written successfully.",LF
62	db "Press any key to reboot.",NULL
63	g_szForeignFlash: db "EEPROM was written successfully.",NULL
64
65
66	; Strings for main menu
67	g_szItemMainExitToDOS: db "Exit to DOS",NULL
68	g_szItemMainLoadFile: db "Load BIOS from file",NULL
69	g_szItemMainLoadROM: db "Load BIOS from EEPROM",NULL
70	g_szItemMainLoadStngs: db "Load old settings from EEPROM",NULL
71	g_szItemMainConfigure: db "Configure XTIDE Universal BIOS",NULL
72	g_szItemMainFlash: db "Flash EEPROM",NULL
73	g_szItemMainSave: db "Save BIOS back to original file",NULL
74	g_szItemMainLicense: db "Copyright and License Information",NULL
75	g_szItemMainHomePage: db "Web Links",NULL
76
77	g_szDlgMainLoadROM: db "Successfully loaded XTIDE Universal BIOS from EEPROM.",NULL
78	g_szDlgMainLoadStngs: db "Successfully loaded settings from EEPROM.",NULL
79	g_szDlgMainLoadFile: db "Successfully loaded file for flashing.",NULL
80	g_szDlgMainSaveFile: db "Successfully saved XTIDE Universal BIOS to file.",NULL
81	g_szDlgMainFileTooBig: db "Selected file is too big to be loaded for flashing!",NULL
82	g_szDlgMainLoadErr: db "Failed to load file!",NULL
83	g_szDlgMainSaveErr: db "Failed to save file!",NULL
84	g_szDlgFileTitle: db "Select file to be flashed.",NULL
85	g_szDlgFileFilter: db ".",NULL
86
87	g_szNfoMainExitToDOS: db "Quits XTIDE Universal BIOS Configurator.",NULL
88	g_szNfoMainLoadFile: db "Load BIOS file to be configured or flashed.",NULL
89	g_szNfoMainLoadROM: db "Load BIOS from EEPROM to be reconfigured.",NULL
90	g_szNfoMainLoadStngs: db "Load old XTIDE Universal BIOS settings from EEPROM.",NULL
91	g_szNfoMainConfigure: db "Configure XTIDE Universal BIOS settings.",NULL
92	g_szNfoMainFlash: db "Flash loaded BIOS image to EEPROM.",NULL
93	g_szNfoMainSave: db "Save BIOS changes back to original file from which it was loaded.",NULL
94	g_szNfoMainLicense: db "XTIDE Universal BIOS and XTIDECFG Copyright (C) 2009-2010 by Tomi Tilli, 2011-2018 by XTIDE Universal BIOS Team."
95	db " Released under GNU GPL v2, with ABSOLUTELY NO WARRANTY. Press ENTER for more details...",NULL
96	g_szNfoMainHomePage: db "Visit http://xtideuniversalbios.org (home page) and http://vcfed.org/forum (support)",NULL
97
98	g_szHelpMainLicense: db "XTIDE Universal BIOS and XTIDECFG Configuration program are Copyright 2009-2010 by Tomi Tilli,"
99	db " 2011-2018 by XTIDE Universal BIOS Team. Released under GNU GPL v2. This software comes with ABSOLUTELY NO WARRANTY."
100	db " This is free software, and you are welcome to redistribute it under certain conditions."
101	db " See the LICENSE.TXT file that was included with this distribution,"
102	db " visit http://www.gnu.org/licenses/ gpl-2.0.html, or visit http://xtideuniversalbios.org.",NULL
103
104	; Strings for XTIDE Universal BIOS configuration menu
105	g_szItemCfgBackToMain: db "Back to Main Menu",NULL
106	g_szItemCfgIde1: db "Primary IDE Controller",NULL
107	g_szItemCfgIde2: db "Secondary IDE Controller",NULL
108	g_szItemCfgIde3: db "Tertiary IDE Controller",NULL
109	g_szItemCfgIde4: db "Quaternary IDE Controller",NULL
110	g_szItemCfgBootMenu: db "Boot settings",NULL
111	g_szItemAutoConfigure: db "Auto Configure",NULL
112	g_szItemCfgFullMode: db "Full operating mode",NULL
113	g_szItemCfgStealSize: db "kiB to steal from RAM",NULL
114	g_szItemCfgIdeCnt: db "IDE controllers",NULL
115	g_szItemCfgIdleTimeout: db "Power Management",NULL
116
117	g_szDlgAutoConfigure: db "Found "
118	g_bControllersDetected: db 'x' ; Value stored directly here
119	db " controllers.",NULL
120	g_szDlgCfgFullMode: db "Enable full operating mode?",NULL
121	g_szDlgCfgStealSize: db "How many kiB of base memory to steal for XTIDE Universal BIOS variables (1...255)?",NULL
122	g_szDlgCfgIdeCnt: db "How many IDE controllers to manage (1...4)?",NULL
123	g_szDlgCfgIdleTimeout: db "Select the amount of time before idling drives should enter standby mode.",NULL
124
125	g_szNfoCfgIde: db "IDE controller and drive configuration.",NULL
126	g_szNfoCfgBootMenu: db "Boot configuration.",NULL
127	g_szNfoAutoConfigure: db "Automatically Configure XTIDE Universal BIOS for this system.",NULL
128	g_szNfoCfgFullMode: db "Full mode supports multiple controllers and has more features.",NULL
129	g_szNfoCfgStealSize: db "How many kiB's to steal from Conventional memory for XTIDE Universal BIOS variables.",NULL
130	g_szNfoCfgIdeCnt: db "Number of IDE controllers to manage.",NULL
131	g_szNfoCfgIdleTimeout: db "Enable Power Management to set the harddrive(s) to spin down after idling a certain amount of time.",NULL
132
133	g_szSerialMoved: db "A Serial Controller has been moved to the end of the Controller list."
134	db " No further action is required. Serial Controllers must be placed at the end of the list.",NULL
135
136	g_szHelpCfgFullMode: db "Full mode supports up to 4 IDE controllers (8 drives). Full mode reserves a bit of RAM from the top of"
137	db " Conventional memory. This makes it possible to use ROM BASIC and other software that requires"
138	db " the interrupt vectors where XTIDE Universal BIOS parameters would be stored in Lite mode.",LF,LF
139	db "Lite mode supports only 2 IDE controllers (4 drives) and stores parameters to the top of the interrupt vectors"
140	db " (30:0h) so no Conventional memory needs to be reserved. Lite mode cannot be used if some software requires"
141	db " the top of interrupt vectors. Usually this is not a problem since only IBM ROM BASIC uses them.",LF,LF
142	db "Tandy 1000 models with 640 kiB or less memory need to use Lite mode since the top of Conventional memory gets"
143	db " dynamically reserved by video hardware. This happens only with Tandy integrated video controller and not when"
144	db " using expansion graphics cards. It is possible to use Full mode if reserving RAM for video memory + what is"
145	db " required for XTIDE Universal BIOS. This would mean 65 kiB but most software should work with 33 kiB reserved.",NULL
146
147	g_szHelpCfgStealSize: db "Parameters for detected hard disks must be stored somewhere. In Full mode they are stored at the top of Conventional"
148	db " memory. 1 kiB is usually enough but you may have to reserve more if you want to use Full mode on a Tandy 1000.",NULL
149
150	g_szHelpCfgIdleTimeout: db "This option enables the standby timer for all harddrives handled by XTIDE Universal BIOS,"
151	db " allowing the drives to spin down after idling the selected amount of time."
152	db " Note that this does not work with old drives that lack the Power Management feature set."
153	db " Also note that timeouts less than 5 minutes may cause unnecessary wear on the drives and is not recommended"
154	db " (use for compatibility testing only).",NULL
155
156	g_szMultichoiceIdleTimeout: db "Disabled",LF
157	db "1 m",LF
158	db "2 m",LF
159	db "3 m",LF
160	db "4 m",LF
161	db "5 m",LF
162	db "6 m",LF
163	db "7 m",LF
164	db "8 m",LF
165	db "9 m",LF
166	db "10 m",LF
167	db "11 m",LF
168	db "12 m",LF
169	db "13 m",LF
170	db "14 m",LF
171	db "15 m",LF
172	db "16 m",LF
173	db "17 m",LF
174	db "18 m",LF
175	db "19 m",LF
176	db "20 m",LF
177	db "30 m",LF
178	db "1 h",LF
179	db "1 h 30 m",LF
180	g_szIdleTimeoutChoice24: db "2 h",NULL
181	g_szIdleTimeoutChoice23: db "1 h 30 m",NULL
182	g_szIdleTimeoutChoice22: db "1 h",NULL
183	g_szIdleTimeoutChoice21: db "30 m",NULL
184	g_szIdleTimeoutChoice20: db "20 m",NULL
185	g_szIdleTimeoutChoice19: db "19 m",NULL
186	g_szIdleTimeoutChoice18: db "18 m",NULL
187	g_szIdleTimeoutChoice17: db "17 m",NULL
188	g_szIdleTimeoutChoice16: db "16 m",NULL
189	g_szIdleTimeoutChoice15: db "15 m",NULL
190	g_szIdleTimeoutChoice14: db "14 m",NULL
191	g_szIdleTimeoutChoice13: db "13 m",NULL
192	g_szIdleTimeoutChoice12: db "12 m",NULL
193	g_szIdleTimeoutChoice11: db "11 m",NULL
194	g_szIdleTimeoutChoice10: db "10 m",NULL
195	g_szIdleTimeoutChoice9: db "9 m",NULL
196	g_szIdleTimeoutChoice8: db "8 m",NULL
197	g_szIdleTimeoutChoice7: db "7 m",NULL
198	g_szIdleTimeoutChoice6: db "6 m",NULL
199	g_szIdleTimeoutChoice5: db "5 m",NULL
200	g_szIdleTimeoutChoice4: db "4 m",NULL
201	g_szIdleTimeoutChoice3: db "3 m",NULL
202	g_szIdleTimeoutChoice2: db "2 m",NULL
203	g_szIdleTimeoutChoice1: db "1 m",NULL
204	g_szIdleTimeoutChoice0: db "Disabled",NULL
205
206	; Strings for IDE Controller menu
207	g_szItemBackToCfgMenu: db "Back to Configuration Menu",NULL
208	g_szItemIdeMaster: db "Master Drive",NULL
209	g_szItemIdeSlave: db "Slave Drive",NULL
210	g_szItemIdeDevice: db "Device type",NULL
211	g_szItemIdeCmdPort: db "Base (cmd block) address",NULL
212	g_szItemIdeCtrlPort: db "Control block address",NULL
213	g_szItemIdeEnIRQ: db "Enable interrupt",NULL
214	g_szItemIdeIRQ: db "IRQ",NULL
215	g_szItemSerialCOM: db "COM Port",NULL
216	g_szItemSerialBaud: db "Baud Rate",NULL
217	g_szItemSerialPort: db "COM Port I/O address",NULL
218	g_szItemIdeSerialComPort: db "COM port",NULL
219	g_szItemIdeSerialBaudRate: db "Baud rate",NULL
220
221	g_szDlgDevice: db "Select controller type.",NULL
222	g_szDlgIdeCmdPort: db "Enter IDE command block (base port) address.",NULL
223	g_szDlgIdeCtrlPort: db "Enter IDE control block address (usually command block + 200h).",NULL
224	g_szDlgIdeEnIRQ: db "Enable interrupt?",NULL
225	g_szDlgIdeIRQ: db "Enter IRQ channel (2...7 for 8-bit controllers, 2...15 for any other controller).",NULL
226	g_szUnsupportedDevice: db "There is no support for this device type in the currently loaded BIOS."
227	db " You must load a BIOS built with the proper module included to be able to use this type of device.",NULL
228
229	g_szNfoIdeBackToCfgMenu: db "Back to XTIDE Universal BIOS Configuration Menu.",NULL
230	g_szNfoIdeMaster: db "Settings for Master Drive.",NULL
231	g_szNfoIdeSlave: db "Settings for Slave Drive.",NULL
232	g_szNfoIdeDevice: db "Select controller device type.",NULL
233	g_szNfoIdeCmdPort: db "IDE Controller Command Block (base port) address or segment address for JR-IDE/ISA and SVC ADP50L.",NULL
234	g_szNfoIdeCtrlPort: db "IDE Controller Control Block address. Usually Cmd Block + 8 for XTIDE, and Cmd Block + 200h for ATA.",NULL
235	g_szNfoIdeEnIRQ: db "Interrupt or polling mode.",NULL
236	g_szNfoIdeIRQ: db "IRQ channel to use.",NULL
237	g_szNfoIdeSerialCOM: db "Select a COM port by number.",NULL
238	g_szNfoIdeSerialBaud: db "Select the COM port's Baud Rate. The server must match this speed."
239	db " Note that UART clock multipliers may impact the actual speed.",NULL
240	g_szNfoIdeSerialPort: db "Select a COM port by custom I/O port address. Any address is valid up to 3F8h, but must be on an 8-byte boundary.",NULL
241
242	g_szHelpIdeCmdPort: db "IDE controller command block address is the usual address mentioned for IDE controllers."
243	db " By default the primary IDE controller uses port 1F0h and secondary controller uses port 170h."
244	db " XTIDE card uses port 300h by default."
245	db " JR-IDE/ISA and SVC ADP50L do not use ports but needs the ROM segment address set here instead.",NULL
246
247	g_szHelpIdeCtrlPort: db "IDE controller Control Block address is normally Command Block address + 200h."
248	db " For XTIDE card the Control Block registers are mapped right after Command Block"
249	db " registers so use Command Block address + 8h for XTIDE card.",NULL
250
251	g_szHelpIdeEnIRQ: db "IDE controller can use interrupts to signal when it is ready to transfer data."
252	db " This makes possible to do other tasks while waiting drive to be ready."
253	db " That is usually not useful in MS-DOS but using interrupts frees the bus for any DMA transfers."
254	db " Polling mode is used when interrupts are disabled."
255	db " Polling usually gives a little better access times since interrupt handling requires extra processing."
256	db " There can be some compatibility issues with some old drives when polling is used with Block Mode transfers.",NULL
257
258	g_szHelpIdeIRQ: db "IRQ channel to use. All controllers managed by XTIDE Universal BIOS can use the same IRQ when MS-DOS is used."
259	db " Other operating systems are likely to require different interrupts for each controller.",NULL
260
261	g_szHelpIdeSerialCOM: db "Select a serial port by COM port number. COM1 through COM4 have well established I/O port assignments,"
262	db ' COM5 and onward are less well established. "COMA" represents COM10, "COMB" represents COM11, and "COMC"'
263	db ' represents COM12. Selecting "COMx" enables the manual selection of an I/O port address.',NULL
264
265	g_szHelpIdeSerialPort: db "Select a serial port by I/O address. Any port address is supported up to 3F8h, but must be on an 8-byte boundary."
266	db " If the entered value corresponds to one of the established COM port numbers, then the selection will snap"
267	db ' to that COM port and "COMx" must be selected again for custom I/O address entry.',NULL
268
269	g_szHelpIdeSerialBaud: db "Supported baud rates are 2400, 4800, 9600, 19.2K, 28.8K, 38.4K, 57.6K, and 115.2K. The server must also be set to"
270	db " this same speed. Older UARTs may only support up to 9600 baud, but sometimes can be pushed to 38.4K. 115.2K will"
271	db " likely only be possible with a newer UART that includes a FIFO. Some high speed serial ports include UART clock"
272	db " multipliers, allowing for speeds at 230.4K (2x multiplier) and 460.8K (4x multiplier) above 115.2K. These high"
273	db " speeds are supported by these BIOS, even on original 4.77MHz 8088 systems. Note that UART clock multipliers are"
274	db " not detectable by the software and 115.2K will still be used during configuration for high speeds; but if"
275	db " a multiplier is used, the actual speed (including the multiplier) will need to be used by the server.",NULL
276
277	g_szMultichoiceCfgDevice: db "16-bit ISA/VLB/PCI IDE",LF
278	db "32-bit VLB/PCI IDE",LF
279	db "16-bit ISA IDE in 8-bit mode",LF
280	db "XTIDE rev 1",LF
281	db "XTIDE rev 2 or modded rev 1",LF
282	db "XT-CF PIO8",LF
283	db "XT-CF PIO8 (BIU offload)",LF
284	db "XT-CF PIO16 (BIU offload)",LF
285	db "XT-CF DMA (v3 only)",LF
286	db "JR-IDE/ISA",LF
287	db "SVC ADP50L",LF
288	db "Serial port virtual device",NULL
289
290	g_szValueCfgDevice16b: db "16-bit",NULL
291	g_szValueCfgDevice32b: db "32-bit",NULL
292	g_szValueCfgDevice8b: db "8-bit",NULL
293	g_szValueCfgDeviceRev1: db "XTIDE r1",NULL
294	g_szValueCfgDeviceRev2: db "XTIDE r2",NULL
295	g_szValueCfgDeviceXTCFPio8: db "XTCF PIO",NULL
296	g_szValueCfgDeviceXTCFPio8WithBIUOffload: db "BIU 8",NULL
297	g_szValueCfgDeviceXTCFPio16WithBIUOffload: db "BIU 16",NULL
298	g_szValueCfgDeviceXTCFDMA: db "XTCF DMA",NULL
299	g_szValueCfgDeviceJrIdeIsa: db "JR-ISA",NULL
300	g_szValueCfgDeviceADP50L: db "ADP50L",NULL
301	g_szValueCfgDeviceSerial: db "Serial",NULL
302
303	g_szSerialCOMChoice: db "COM1 - address 3F8h",LF
304	db "COM2 - address 2F8h",LF
305	db "COM3 - address 3E8h",LF
306	db "COM4 - address 2E8h",LF
307	db "COM5 - address 2F0h",LF
308	db "COM6 - address 3E0h",LF
309	db "COM7 - address 2E0h",LF
310	db "COM8 - address 260h",LF
311	db "COM9 - address 368h",LF
312	db "COMA - address 268h",LF
313	db "COMB - address 360h",LF
314	db "COMC - address 270h",LF
315	db "COMx - Custom address",NULL
316
317	g_szValueCfgCOM1: db "COM1",NULL
318	g_szValueCfgCOM2: db "COM2",NULL
319	g_szValueCfgCOM3: db "COM3",NULL
320	g_szValueCfgCOM4: db "COM4",NULL
321	g_szValueCfgCOM5: db "COM5",NULL
322	g_szValueCfgCOM6: db "COM6",NULL
323	g_szValueCfgCOM7: db "COM7",NULL
324	g_szValueCfgCOM8: db "COM8",NULL
325	g_szValueCfgCOM9: db "COM9",NULL
326	g_szValueCfgCOMA: db "COMA",NULL
327	g_szValueCfgCOMB: db "COMB",NULL
328	g_szValueCfgCOMC: db "COMC",NULL
329	g_szValueCfgCOMx: db "Custom",NULL
330
331	g_szSerialBaudChoice: db "115.2K baud",LF
332	db "57.6K baud",LF
333	db "38.4K baud",LF
334	db "28.8K baud",LF
335	db "19.2K baud",LF
336	db "9600 baud",LF
337	db "4800 baud",LF
338	db "2400 baud",NULL
339
340	g_szValueCfgBaud115_2: db "115.2K",NULL
341	g_szValueCfgBaud57_6: db "57.6K",NULL
342	g_szValueCfgBaud38_4: db "38.4K",NULL
343	g_szValueCfgBaud28_8: db "28.8K",NULL
344	g_szValueCfgBaud19_2: db "19.2K",NULL
345	g_szValueCfgBaud9600: db "9600",NULL
346	g_szValueCfgBaud4800: db "4800",NULL
347	g_szValueCfgBaud2400: db "2400",NULL
348
349
350	; Strings for DRVPARAMS menu
351	g_szItemDrvBackToIde: db "Back to IDE Controller Menu",NULL
352	g_szItemDrvBlockMode: db "Block Mode Transfers",NULL
353	g_szItemDrvXlateMode: db "CHS translation method",NULL
354	g_szItemDrvWriteCache: db "Internal Write Cache",NULL
355	g_szItemDrvUserCHS: db "User specified CHS",NULL
356	g_szItemDrvCyls: db "Cylinders",NULL
357	g_szItemDrvHeads: db "Heads",NULL
358	g_szItemDrvSect: db "Sectors per track",NULL
359	g_szItemDrvUserLBA: db "User specified LBA",NULL
360	g_szItemDrvLbaSectors: db "Millions of sectors",NULL
361
362	g_szDlgDrvBlockMode: db "Enable Block Mode Transfers?",NULL
363	g_szDlgDrvXlateMode: db "Select P-CHS to L-CHS translation method.",NULL
364	g_szDlgDrvWriteCache: db "Select hard drive internal write cache settings.",NULL
365	g_szDlgDrvUserCHS: db "Specify (P-)CHS parameters manually?",NULL
366	g_szDlgDrvCyls: db "Enter number of P-CHS cylinders (1...16383).",NULL
367	g_szDlgDrvHeads: db "Enter number of P-CHS heads (1...16).",NULL
368	g_szDlgDrvSect: db "Enter number of sectors per track (1...63).",NULL
369	g_szDlgDrvUserLBA: db "Limit drive capacity?",NULL
370	g_szDlgDrvLbaSectors: db "Enter maximum capacity in millions of sectors (16...256).",NULL
371
372	g_szNfoDrvBlockMode: db "Transfer multiple sectors per data request.",NULL
373	g_szNfoDrvXlateMode: db "P-CHS to L-CHS translation method.",NULL
374	g_szNfoDrvWriteCache: db "Hard Drive Internal Write Cache settings (WARNING!).",NULL
375	g_szNfoDrvUserCHS: db "Specify (P-)CHS parameters manually instead of autodetecting them.",NULL
376	g_szNfoDrvCyls: db "Number of user specified P-CHS cylinders.",NULL
377	g_szNfoDrvHeads: db "Number of user specified P-CHS heads.",NULL
378	g_szNfoDrvSect: db "Number of user specified P-CHS sectors per track.",NULL
379	g_szNfoDrvUserLBA: db "Limit drive capacity to fix compatibility problems with Windows 9x.",NULL
380	g_szNfoDrvLbaSectors: db "Millions of sectors (1024*1024). 1M sectors = 512 MiB. Recommended limits are 64 for Windows 95, 128 for Windows 98 and 256 for Windows ME (and 98 with updated fdisk).",NULL
381
382	g_szHelpDrvBlockMode: db "Block Mode will speed up transfers since multiple sectors can be transferred before waiting next data request."
383	db " Normally Block Mode should always be kept enabled but there is at"
384	db " least one drive with buggy Block Mode implementation.",NULL
385
386	g_szHelpDrvWriteCache: db "Modern Hard Drives have a large amount of internal write cache."
387	db " The cache will speed up writes since the drive can free the bus right after data has been written to cache."
388	db " The drive then starts to write the data from cache to disk by itself."
389	db " This can be dangerous since all unwritten data in cache is lost if power is turned off or the system is reset."
390	db " Modern operating systems will flush the cache when user shuts down the system."
391	db " DOS does not have that sort of protection so it is up to the user to make sure cache is flushed."
392	db " WARNING!!! Write cache should be left disabled.",NULL
393
394	g_szHelpDrvUserCHS: db "Specify (P-)CHS parameters manually instead of autodetecting them."
395	db " This can be used to limit drive size for old operating systems that do not support large hard disks."
396	db " Some early IDE drives have buggy autodetection so they require CHS to be specified manually."
397	db " Limiting Cylinders will work for all drives but drives may not accept all values for Heads and Sectors per Track.",NULL
398
399	g_szHelpDrvUserLBA: db "Limit drive size to X million sectors for EBIOS functions. This option is useful to"
400	db " prevent large drive compatibility problems with MS-DOS 7.x (Windows 95 and 98).",NULL
401
402	g_szMultichoiseXlateMode:
403	db "NORMAL",LF
404	db "LARGE",LF
405	db "Assisted LBA",LF
406	db "Autodetect",NULL
407
408	g_szValueDrvXlateNormal:db "NORMAL",NULL
409	g_szValueDrvXlateLarge: db "LARGE",NULL
410	g_szValueDrvXlateLBA: db "LBA",NULL
411	g_szValueDrvXlateAuto: db "Auto",NULL
412
413	g_szMultichoiseWrCache: db "Drive Default",LF
414	db "Disable Write Cache",LF
415	db "Enable Write Cache",NULL
416
417	g_szValueDrvWrCaDis: db "Disabled",NULL
418	g_szValueDrvWrCaEn: db "Enabled",NULL
419
420
421	; Strings for boot settings menu
422	g_szItemBootTimeout: db "Selection timeout",NULL
423	g_szItemBootDrive: db "Default boot drive",NULL
424	g_szItemBootDispMode: db "Display Mode",NULL
425	g_szItemColorTheme: db "Color Theme",NULL
426	g_szItemBootFloppyDrvs: db "Number of Floppy Drives",NULL
427	g_szItemSerialDetect: db "Scan for Serial Drives",NULL
428
429	g_szDlgBootTimeout: db "Enter Boot Menu selection timeout in BIOS timer ticks (2...1092).",NULL
430	g_szDlgBootDrive: db "Enter default drive number (0xh for Floppy Drives, 8xh for Hard Disks).",NULL
431	g_szDlgBootDispMode: db "Select display mode.",NULL
432	g_szDlgColorTheme: db "Select color theme.",NULL
433	g_szDlgBootFloppyDrvs: db "Select number of Floppy Drives in system.",NULL
434	g_szDlgSerialDetect: db "Scan for serial drives?",NULL
435
436	g_szNfoBootTimeout: db "Menu item selection timeout in BIOS timer ticks. 1 tick = 54.9 ms.",NULL
437	g_szNfoBootDrive: db "Default boot drive.",NULL
438	g_szNfoDispMode: db "Display mode to set when booting.",NULL
439	g_szNfoColorTheme: db "Color theme used by the boot menu and the hotkey bar.",NULL
440	g_szNfoBootFloppyDrvs: db "Number of Floppy Drives in system.",NULL
441	g_szNfoSerialDetect: db "Scans all standard COM ports for serial drives."
442	db " This can also be invoked by holding down ALT at the end of normal drive detection.",NULL
443
444	g_szHelpBootTimeout: db "Boot Menu selection timeout in BIOS timer ticks (1 second = 18.2 ticks)."
445	db " When timer goes to zero, currently selected drive will be booted automatically."
446	db " Timeout can be disabled by setting this to 0.",NULL
447	g_szHelpBootDrive: db "Drive to be set selected by default when Boot Menu is displayed.",NULL
448	g_szHelpColorTheme: db "Pick a theme from a list of several pre-defined themes to customize the colors used by the boot menu and, if"
449	db " available, the hotkey bar. Selecting a theme or loading a BIOS, or its settings, from file or from ROM will"
450	db " make XTIDECFG apply the theme to itself for easy preview. The ability to preview themes requires that"
451	db " XTIDECFG is running in a display mode that can display colors. In other words, you may configure the"
452	db " BIOS on a machine with a monochrome graphics adapter and not be able to preview the theme but the BIOS will"
453	db " still use the selected theme when installed in a machine with a color graphics adapter.",NULL
454	g_szHelpBootFloppyDrvs: db "Detecting the correct number of floppy drives might fail when using a floppy controller with its own BIOS."
455	db " A minimum number of floppy drives can be specified to force non-detected drives to appear on boot menu.",NULL
456	g_szHelpSerialDetect: db "Set to Yes, at the end of normal drive detection, COM ports 1-7 (in reverse order) will be scanned for a connection"
457	db " to a serial drive server. This option provides flexibility with the COM port and baud rate to be used,"
458	db " it need not be configured ahead of time, but at the expense of a slower boot process."
459	db " Even when this option is set to No, this functionality can still be invoked by holding down the ALT key at the end"
460	db " of normal drive detection. Note that if any serial drives are detected during the normal drive detection,"
461	db " no scan will take place (to avoid finding the same drive twice).",NULL
462
463	g_szMultichoiceBootDispMode: db "Default",LF
464	db "40x25 Black & White",LF
465	db "40x25 Color",LF
466	db "80x25 Black & White",LF
467	db "80x25 Color",LF
468	db "80x25 Monochrome",NULL
469
470	g_szValueBootDispModeDefault: db "Default",NULL
471	g_szValueBootDispModeBW40: db "BW40",NULL
472	g_szValueBootDispModeCO40: db "CO40",NULL
473	g_szValueBootDispModeBW80: db "BW80",NULL
474	g_szValueBootDispModeCO80: db "CO80",NULL
475	g_szValueBootDispModeMono: db "Mono",NULL
476
477	g_szMultichoiceColorTheme: db "Classic (default)",LF
478	db "Argon Blue",LF
479	db "Neon Red",LF
480	db "Phosphor Green",LF
481	db "Moon Surface",LF
482	db "Toxic Waste",NULL
483	g_szValueColorTheme0: db "Classic",NULL
484	g_szValueColorTheme1: db "Argon",NULL
485	g_szValueColorTheme2: db "Neon",NULL
486	g_szValueColorTheme3: db "Phosphor",NULL
487	g_szValueColorTheme4: db "Moon",NULL
488	g_szValueColorTheme5: db "Toxic",NULL
489
490	g_szMultichoiceBootFloppyDrvs: db "Autodetect",LF
491	db "1",LF
492	db "2",LF
493	db "3",LF
494	g_szValueBootFloppyDrvs4: db "4",NULL
495	g_szValueBootFloppyDrvs3: db "3",NULL
496	g_szValueBootFloppyDrvs2: db "2",NULL
497	g_szValueBootFloppyDrvs1: db "1",NULL
498	g_szValueBootFloppyDrvsAuto: db "Auto",NULL
499
500
501	; Strings for Flash menu
502	g_szItemFlashStart: db "Start flashing",NULL
503	g_szItemFlashEepromType:db "EEPROM type",NULL
504	g_szItemFlashSDP: db "SDP command",NULL
505	g_szItemFlashAddr: db "EEPROM address",NULL
506	g_szItemFlashPageSize: db "Page size",NULL
507	g_szItemFlashChecksum: db "Generate checksum byte",NULL
508
509	g_szDlgFlashEepromType: db "Select EEPROM type.",NULL
510	g_szDlgFlashSDP: db "Select Software Data Protection command.",NULL
511	g_szDlgFlashAddr: db "Enter segment address where EEPROM is located.",NULL
512	g_szDlgFlashPageSize: db "Select write page size.",NULL
513	g_szDlgFlashChecksum: db "Generate checksum byte to the end of BIOS image?",NULL
514
515	g_szNfoFlashEepromType: db "EEPROM type.",NULL
516	g_szNfoFlashStart: db "Writes BIOS to EEPROM.",NULL
517	g_szNfoFlashSDP: db "Software Data Protection command.",NULL
518	g_szNfoFlashAddr: db "Address (segment) where EEPROM is located.",NULL
519	g_szNfoFlashPageSize: db "Number of bytes to write before delay.",NULL
520	g_szNfoFlashChecksum: db "Generate checksum byte to the end of BIOS image.",NULL
521
522	g_szHelpFlashSDP: db "Software Data Protection Command:",LF
523	db "None = Do not use Software Data Protection. Meant for EEPROMs that do not support SDP.",LF,LF
524	db "Enable = Write protects the EEPROM after flashing."
525	db " Software Data Protection should always be enabled if EEPROM supports it.",LF,LF
526	db "Disable = Disables Software Data Protection after flashing.",NULL
527
528	g_szHelpFlashPageSize: db "Larger page size will improve write performance but not all EEPROMs support large pages or page writing at all."
529	db " Byte writing mode will be used when page size is set to 1. Byte writing mode is supported by all EEPROMs."
530	db " Large pages cannot be flashed with slow CPUs.",NULL
531
532	g_szHelpFlashChecksum: db "PC BIOSes require a checksum byte at the end of expansion card BIOS ROMs."
533	db " You might not want to generate checksum byte when flashing some other images than XTIDE Universal BIOS.",NULL
534
535	g_szMultichoiceEepromType:
536	db "2816 (2 kiB)",LF
537	db "2864 (8 kiB)",LF
538	db "2864 mod (8 kiB)",LF
539	db "28256 (32 kiB)",LF
540	db "28512 (64 kiB)",NULL
541	g_szValueFlash2816: db "2816",NULL
542	g_szValueFlash2864: db "2864",NULL
543	g_szValueFlash2864Mod: db "2864mod",NULL
544	g_szValueFlash28256: db "28256",NULL
545	g_szValueFlash28512: db "28512",NULL
546
547	g_szMultichoiceSdpCommand:
548	db "None",LF
549	db "Enable",LF
550	g_szValueFlashDisable: db "Disable",NULL
551	g_szValueFlashEnable: db "Enable",NULL
552	g_szValueFlashNone: db "None",NULL
553
554	g_szMultichoicePageSize:
555	db "1 byte",LF
556	db "2 bytes",LF
557	db "4 bytes",LF
558	db "8 bytes",LF
559	db "16 bytes",LF
560	db "32 bytes",LF
561	g_szValueFlash64bytes: db "64 bytes",NULL
562	g_szValueFlash32bytes: db "32 bytes",NULL
563	g_szValueFlash16bytes: db "16 bytes",NULL
564	g_szValueFlash8bytes: db "8 bytes",NULL
565	g_szValueFlash4bytes: db "4 bytes",NULL
566	g_szValueFlash2bytes: db "2 bytes",NULL
567	g_szValueFlash1byte: db "1 byte",NULL
568
569	g_szSelectionTimeout: db DOUBLE_BOTTOM_LEFT_CORNER,DOUBLE_LEFT_HORIZONTAL_TO_SINGLE_VERTICAL,"%ASelection in %2u s",NULL
570	g_szDashForZero: db "- ",NULL
571	g_szValueUnknownError: db "Error!",NULL
572

Note: See TracBrowser for help on using the repository browser.

Context Navigation

source: xtideuniversalbios/trunk/XTIDE_Universal_BIOS_Configurator_v2/Src/Strings.asm@ 595

Download in other formats: