source: xtideuniversalbios/trunk/XTIDE_Universal_BIOS_Configurator_v2/Src/Strings.asm@ 576

Last change on this file since 576 was 567, checked in by krille_n_@…, 11 years ago

Changes:

  • Renamed MODULE_FEATURE_SETS to MODULE_POWER_MANAGEMENT.
  • Renamed MODULE_VERY_LATE_INITIALIZATION to MODULE_VERY_LATE_INIT and removed it from the official builds.
  • Removed the code that skips detection of slave drives on XT-CF controllers since slave drives can be used with Lo-tech ISA CompactFlash boards.
  • Added autodetection of the SVC ADP50L controller to XTIDECFG.
  • The autodetection of XT-CF controllers now requires MODULE_8BIT_IDE_ADVANCED in the loaded BIOS.
  • Fixed a bug in XTIDECFG from r502 where the "Base (cmd block) address" menu option would be displayed when a serial device was selected as the IDE controller.
  • XTIDECFG would display the "Enable interrupt" menu option for the XTIDE r1 but not for the XTIDE r2. It's now displayed for both controller types.
  • Disabled the "Internal Write Cache" menu option in the Master/Slave Drive menus for serial device type drives.
  • Optimizations and other fixes.
File size: 28.2 KB
Line 
1; Project name : XTIDE Universal BIOS Configurator v2
2; Description : All strings.
3
4;
5; XTIDE Universal BIOS and Associated Tools
6; Copyright (C) 2009-2010 by Tomi Tilli, 2011-2013 by XTIDE Universal BIOS Team.
7;
8; This program is free software; you can redistribute it and/or modify
9; it under the terms of the GNU General Public License as published by
10; the Free Software Foundation; either version 2 of the License, or
11; (at your option) any later version.
12;
13; This program is distributed in the hope that it will be useful,
14; but WITHOUT ANY WARRANTY; without even the implied warranty of
15; MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16; GNU General Public License for more details.
17; Visit http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
18;
19
20; Section containing initialized data
21SECTION .data
22
23; Menu title
24g_szProgramTitle: db "Configuration and Flashing program for XTIDE Universal BIOS v2.0.0.",LF,CR,NULL
25g_szXtideUniversalBiosSignature: db "XTIDE204",NULL
26g_szBiosIsNotLoaded: db "BIOS is not loaded!",NULL
27g_szEEPROM: db "EEPROM",NULL
28g_szSourceAndTypeSeparator: db " : ",NULL
29g_szUnidentified: db "Unidentified",NULL
30g_szUnsaved: db " ",SINGLE_LEFT_HORIZONTAL_TO_VERTICAL,"Unsaved",SINGLE_RIGHT_HORIZONTAL_TO_VERTICAL,NULL
31
32; Item formatting
33g_szFormatItemWithoutValue: db "%c%s",NULL
34g_szFormatItemNameWithValue: db "%25s%-10S",NULL
35
36
37g_szNo: db "No",NULL
38g_szMultichoiceBooleanFlag: db "No",LF
39g_szYes: db "Yes",NULL
40
41; Exit messages
42g_szDlgExitToDos: db "Exit to DOS?",NULL
43g_szDlgSaveChanges: db "Do you want to save changes to XTIDE Universal BIOS image file?",NULL
44
45
46; Generic dialog strings
47g_szNotificationDialog: db "Notification.",NULL
48g_szErrorDialog: db "Error!",NULL
49g_szGenericDialogInfo: db "Press ENTER or ESC to close dialog.",NULL
50
51; Flashing related strings
52g_szFlashTitle: db "Flashing EEPROM, please wait.",NULL
53g_szErrEepromTooSmall: db "Image is too large for selected EEPROM type!",NULL
54g_szErrEepromPolling: db "Timeout when polling EEPROM.",LF
55 db "EEPROM was not flashed properly!",NULL
56g_szErrEepromVerify: db "EEPROM did not return the same byte that was written.",LF
57 db "EEPROM was not flashed properly!",NULL
58g_szPCFlashSuccessful: db "EEPROM was written successfully.",LF
59 db "Press any key to reboot.",NULL
60g_szForeignFlash: db "EEPROM was written successfully.",NULL
61
62
63; Strings for main menu
64g_szItemMainExitToDOS: db "Exit to DOS",NULL
65g_szItemMainLoadFile: db "Load BIOS from file",NULL
66g_szItemMainLoadROM: db "Load BIOS from EEPROM",NULL
67g_szItemMainLoadStngs: db "Load old settings from EEPROM",NULL
68g_szItemMainConfigure: db "Configure XTIDE Universal BIOS",NULL
69g_szItemMainFlash: db "Flash EEPROM",NULL
70g_szItemMainSave: db "Save BIOS back to original file",NULL
71g_szItemMainLicense: db "Copyright and License Information",NULL
72g_szItemMainHomePage: db "Web Links",NULL
73
74g_szDlgMainLoadROM: db "Successfully loaded XTIDE Universal BIOS from EEPROM.",NULL
75g_szDlgMainLoadStngs: db "Successfully loaded settings from EEPROM.",NULL
76g_szDlgMainLoadFile: db "Successfully loaded file for flashing.",NULL
77g_szDlgMainSaveFile: db "Successfully saved XTIDE Universal BIOS to file.",NULL
78g_szDlgMainFileTooBig: db "Selected file is too big to be loaded for flashing!",NULL
79g_szDlgMainLoadErr: db "Failed to load file!",NULL
80g_szDlgMainSaveErr: db "Failed to save file!",NULL
81g_szDlgFileTitle: db "Select file to be flashed.",NULL
82g_szDlgFileFilter: db "*.*",NULL
83
84g_szNfoMainExitToDOS: db "Quits XTIDE Universal BIOS Configurator.",NULL
85g_szNfoMainLoadFile: db "Load BIOS file to be configured or flashed.",NULL
86g_szNfoMainLoadROM: db "Load BIOS from EEPROM to be reconfigured.",NULL
87g_szNfoMainLoadStngs: db "Load old XTIDE Universal BIOS settings from EEPROM.",NULL
88g_szNfoMainConfigure: db "Configure XTIDE Universal BIOS settings.",NULL
89g_szNfoMainFlash: db "Flash loaded BIOS image to EEPROM.",NULL
90g_szNfoMainSave: db "Save BIOS changes back to original file from which it was loaded.",NULL
91g_szNfoMainLicense: db "XTIDE Universal BIOS and XTIDECFG Copyright (C) 2009-2010 by Tomi Tilli, 2011-2013 by XTIDE Universal BIOS Team."
92 db " Released under GNU GPL v2, with ABSOLUTELY NO WARRANTY. Press ENTER for more details...",NULL
93g_szNfoMainHomePage: db "Visit http://code.google.com/p/ xtideuniversalbios (home page) and http://vintage-computer.com/ vcforum (support)",NULL
94
95g_szHelpMainLicense: db "XTIDE Universal BIOS and XTIDECFG Configuration program are Copyright 2009-2010 by Tomi Tilli,"
96 db " 2011-2013 by XTIDE Universal BIOS Team. Released under GNU GPL v2. This software comes with ABSOLUTELY NO WARRANTY."
97 db " This is free software, and you are welcome to redistribute it under certain conditions."
98 db " See the LICENSE.TXT file that was included with this distribution,"
99 db " visit http://www.gnu.org/licenses/ gpl-2.0.html, or visit http://code.coogle.com/p/ xtideuniversalbios.",NULL
100
101; Strings for XTIDE Universal BIOS configuration menu
102g_szItemCfgBackToMain: db "Back to Main Menu",NULL
103g_szItemCfgIde1: db "Primary IDE Controller",NULL
104g_szItemCfgIde2: db "Secondary IDE Controller",NULL
105g_szItemCfgIde3: db "Tertiary IDE Controller",NULL
106g_szItemCfgIde4: db "Quaternary IDE Controller",NULL
107g_szItemCfgBootMenu: db "Boot settings",NULL
108g_szItemAutoConfigure: db "Auto Configure",NULL
109g_szItemCfgFullMode: db "Full operating mode",NULL
110g_szItemCfgStealSize: db "kiB to steal from RAM",NULL
111g_szItemCfgIdeCnt: db "IDE controllers",NULL
112g_szItemCfgIdleTimeout: db "Power Management",NULL
113
114g_szDlgAutoConfigure: db "Found "
115g_bControllersDetected: db 'x' ; Value stored directly here
116 db " controllers.",NULL
117g_szDlgCfgFullMode: db "Enable full operating mode?",NULL
118g_szDlgCfgStealSize: db "How many kiB of base memory to steal for XTIDE Universal BIOS variables (1...255)?",NULL
119g_szDlgCfgIdeCnt: db "How many IDE controllers to manage (1...4)?",NULL
120g_szDlgCfgIdleTimeout: db "Select the amount of time before idling drives should enter standby mode.",NULL
121
122g_szNfoCfgIde: db "IDE controller and drive configuration.",NULL
123g_szNfoCfgBootMenu: db "Boot configuration.",NULL
124g_szNfoAutoConfigure: db "Automatically Configure XTIDE Universal BIOS for this system.",NULL
125g_szNfoCfgFullMode: db "Full mode supports multiple controllers and has more features.",NULL
126g_szNfoCfgStealSize: db "How many kiB's to steal from Conventional memory for XTIDE Universal BIOS variables.",NULL
127g_szNfoCfgIdeCnt: db "Number of IDE controllers to manage.",NULL
128g_szNfoCfgIdleTimeout: db "Enable Power Management to set the harddrive(s) to spin down after idling a certain amount of time.",NULL
129
130g_szSerialMoved: db "A Serial Controller has been moved to the end of the Controller list."
131 db " No further action is required. Serial Controllers must be placed at the end of the list.",NULL
132
133g_szHelpCfgFullMode: db "Full mode supports up to 4 IDE controllers (8 drives). Full mode reserves a bit of RAM from the top of"
134 db " Conventional memory. This makes it possible to use ROM BASIC and other software that requires"
135 db " the interrupt vectors where XTIDE Universal BIOS parameters would be stored in Lite mode.",LF,LF
136 db "Lite mode supports only one IDE controller (2 drives) and stores parameters to the top of the interrupt vectors"
137 db " (30:0h) so no Conventional memory needs to be reserved. Lite mode cannot be used if some software requires"
138 db " the top of interrupt vectors. Usually this is not a problem since only IBM ROM BASIC uses them.",LF,LF
139 db "Tandy 1000 models with 640 kiB or less memory need to use Lite mode since the top of Conventional memory gets"
140 db " dynamically reserved by video hardware. This happens only with Tandy integrated video controller and not when"
141 db " using expansion graphics cards. It is possible to use Full mode if reserving RAM for video memory + what is"
142 db " required for XTIDE Universal BIOS. This would mean 65 kiB but most software should work with 33 kiB reserved.",NULL
143
144g_szHelpCfgStealSize: db "Parameters for detected hard disks must be stored somewhere. In Full mode they are stored at the top of Conventional"
145 db " memory. 1 kiB is usually enough but you may have to reserve more if you want to use Full mode on a Tandy 1000.",NULL
146
147g_szHelpCfgIdleTimeout: db "This option enables the standby timer for all harddrives handled by XTIDE Universal BIOS,"
148 db " allowing the drives to spin down after idling the selected amount of time."
149 db " Note that this does not work with old drives that lack the Power Management feature set."
150 db " Also note that timeouts less than 5 minutes may cause unnecessary wear on the drives and is not recommended"
151 db " (use for compatibility testing only).",NULL
152
153g_szMultichoiceIdleTimeout: db "Disabled",LF
154 db "1 m",LF
155 db "2 m",LF
156 db "3 m",LF
157 db "4 m",LF
158 db "5 m",LF
159 db "6 m",LF
160 db "7 m",LF
161 db "8 m",LF
162 db "9 m",LF
163 db "10 m",LF
164 db "11 m",LF
165 db "12 m",LF
166 db "13 m",LF
167 db "14 m",LF
168 db "15 m",LF
169 db "16 m",LF
170 db "17 m",LF
171 db "18 m",LF
172 db "19 m",LF
173 db "20 m",LF
174 db "30 m",LF
175 db "1 h",LF
176 db "1 h 30 m",LF
177g_szIdleTimeoutChoice24: db "2 h",NULL
178g_szIdleTimeoutChoice23: db "1 h 30 m",NULL
179g_szIdleTimeoutChoice22: db "1 h",NULL
180g_szIdleTimeoutChoice21: db "30 m",NULL
181g_szIdleTimeoutChoice20: db "20 m",NULL
182g_szIdleTimeoutChoice19: db "19 m",NULL
183g_szIdleTimeoutChoice18: db "18 m",NULL
184g_szIdleTimeoutChoice17: db "17 m",NULL
185g_szIdleTimeoutChoice16: db "16 m",NULL
186g_szIdleTimeoutChoice15: db "15 m",NULL
187g_szIdleTimeoutChoice14: db "14 m",NULL
188g_szIdleTimeoutChoice13: db "13 m",NULL
189g_szIdleTimeoutChoice12: db "12 m",NULL
190g_szIdleTimeoutChoice11: db "11 m",NULL
191g_szIdleTimeoutChoice10: db "10 m",NULL
192g_szIdleTimeoutChoice9: db "9 m",NULL
193g_szIdleTimeoutChoice8: db "8 m",NULL
194g_szIdleTimeoutChoice7: db "7 m",NULL
195g_szIdleTimeoutChoice6: db "6 m",NULL
196g_szIdleTimeoutChoice5: db "5 m",NULL
197g_szIdleTimeoutChoice4: db "4 m",NULL
198g_szIdleTimeoutChoice3: db "3 m",NULL
199g_szIdleTimeoutChoice2: db "2 m",NULL
200g_szIdleTimeoutChoice1: db "1 m",NULL
201g_szIdleTimeoutChoice0: db "Disabled",NULL
202
203; Strings for IDE Controller menu
204g_szItemBackToCfgMenu: db "Back to Configuration Menu",NULL
205g_szItemIdeMaster: db "Master Drive",NULL
206g_szItemIdeSlave: db "Slave Drive",NULL
207g_szItemIdeDevice: db "Device type",NULL
208g_szItemIdeCmdPort: db "Base (cmd block) address",NULL
209g_szItemIdeCtrlPort: db "Control block address",NULL
210g_szItemIdeEnIRQ: db "Enable interrupt",NULL
211g_szItemIdeIRQ: db "IRQ",NULL
212g_szItemSerialCOM: db "COM Port",NULL
213g_szItemSerialBaud: db "Baud Rate",NULL
214g_szItemSerialPort: db "COM Port I/O address",NULL
215g_szItemIdeSerialComPort: db "COM port",NULL
216g_szItemIdeSerialBaudRate: db "Baud rate",NULL
217
218g_szDlgDevice: db "Select controller type.",NULL
219g_szDlgIdeCmdPort: db "Enter IDE command block (base port) address.",NULL
220g_szDlgIdeCtrlPort: db "Enter IDE control block address (usually command block + 200h).",NULL
221g_szDlgIdeEnIRQ: db "Enable interrupt?",NULL
222g_szDlgIdeIRQ: db "Enter IRQ channel (2...7 for 8-bit controllers, 2...15 for any other controller).",NULL
223
224g_szNfoIdeBackToCfgMenu: db "Back to XTIDE Universal BIOS Configuration Menu.",NULL
225g_szNfoIdeMaster: db "Settings for Master Drive.",NULL
226g_szNfoIdeSlave: db "Settings for Slave Drive.",NULL
227g_szNfoIdeDevice: db "Select controller device type.",NULL
228g_szNfoIdeCmdPort: db "IDE Controller Command Block (base port) address or segment address for JR-IDE/ISA and SVC ADP50L.",NULL
229g_szNfoIdeCtrlPort: db "IDE Controller Control Block address. Usually Cmd Block + 8 for XTIDE, and Cmd Block + 200h for ATA.",NULL
230g_szNfoIdeEnIRQ: db "Interrupt or polling mode.",NULL
231g_szNfoIdeIRQ: db "IRQ channel to use.",NULL
232g_szNfoIdeSerialCOM: db "Select a COM port by number.",NULL
233g_szNfoIdeSerialBaud: db "Select the COM port's Baud Rate. The server must match this speed."
234 db " Note that UART clock multipliers may impact the actual speed.",NULL
235g_szNfoIdeSerialPort: db "Select a COM port by custom I/O port address. Any address is valid up to 3F8h, but must be on an 8-byte boundary.",NULL
236
237g_szHelpIdeCmdPort: db "IDE controller command block address is the usual address mentioned for IDE controllers."
238 db " By default the primary IDE controller uses port 1F0h and secondary controller uses port 170h."
239 db " XTIDE card uses port 300h by default."
240 db " JR-IDE/ISA and SVC ADP50L do not use ports but needs the ROM segment address set here instead.",NULL
241
242g_szHelpIdeCtrlPort: db "IDE controller Control Block address is normally Command Block address + 200h."
243 db " For XTIDE card the Control Block registers are mapped right after Command Block"
244 db " registers so use Command Block address + 8h for XTIDE card.",NULL
245
246g_szHelpIdeEnIRQ: db "IDE controller can use interrupts to signal when it is ready to transfer data."
247 db " This makes possible to do other tasks while waiting drive to be ready."
248 db " That is usually not useful in MS-DOS but using interrupts frees the bus for any DMA transfers."
249 db " Polling mode is used when interrupts are disabled."
250 db " Polling usually gives a little better access times since interrupt handling requires extra processing."
251 db " There can be some compatibility issues with some old drives when polling is used with Block Mode transfers.",NULL
252
253g_szHelpIdeIRQ: db "IRQ channel to use. All controllers managed by XTIDE Universal BIOS can use the same IRQ when MS-DOS is used."
254 db " Other operating systems are likely to require different interrupts for each controller.",NULL
255
256g_szHelpIdeSerialCOM: db "Select a serial port by COM port number. COM1 through COM4 have well established I/O port assignments,"
257 db ' COM5 and onward are less well established. "COMA" represents COM10, "COMB" represents COM11, and "COMC"'
258 db ' represents COM12. Selecting "COMx" enables the manual selection of an I/O port address.',NULL
259
260g_szHelpIdeSerialPort: db "Select a serial port by I/O address. Any port address is supported up to 3F8h, but must be on an 8-byte boundary."
261 db " If the entered value corresponds to one of the established COM port numbers, then the selection will snap"
262 db ' to that COM port and "COMx" must be selected again for custom I/O address entry.',NULL
263
264g_szHelpIdeSerialBaud: db "Supported baud rates are 2400, 4800, 9600, 19.2K, 28.8K, 38.4K, 57.6K, and 115.2K. The server must also be set to"
265 db " this same speed. Older UARTs may only support up to 9600 baud, but sometimes can be pushed to 38.4K. 115.2K will"
266 db " likely only be possible with a newer UART that includes a FIFO. Some high speed serial ports include UART clock"
267 db " multipliers, allowing for speeds at 230.4K (2x multiplier) and 460.8K (4x multiplier) above 115.2K. These high"
268 db " speeds are supported by these BIOS, even on original 4.77MHz 8088 systems. Note that UART clock multipliers are"
269 db " not detectable by the software and 115.2K will still be used during configuration for high speeds; but if"
270 db " a multiplier is used, the actual speed (including the multiplier) will need to be used by the server.",NULL
271
272g_szMultichoiceCfgDevice: db "16-bit ISA/VLB/PCI IDE",LF
273 db "32-bit VLB/PCI IDE",LF
274 db "16-bit ISA IDE in 8-bit mode",LF
275 db "XTIDE rev 1",LF
276 db "XTIDE rev 2 or modded rev 1",LF
277 db "XT-CF (PIO)",LF
278 db "XT-CF (PIO w/BIU offload)",LF
279 db "XT-CF DMA (v3 only)",LF
280 db "JR-IDE/ISA",LF
281 db "SVC ADP50L",LF
282 db "Serial port virtual device",NULL
283
284g_szValueCfgDevice16b: db "16-bit",NULL
285g_szValueCfgDevice32b: db "32-bit",NULL
286g_szValueCfgDevice8b: db "8-bit",NULL
287g_szValueCfgDeviceRev1: db "XTIDE r1",NULL
288g_szValueCfgDeviceRev2: db "XTIDE r2",NULL
289g_szValueCfgDeviceXTCFPio8: db "XTCF PIO",NULL
290g_szValueCfgDeviceXTCFPio8WithBIUOffload: db "XTCF BIU",NULL
291g_szValueCfgDeviceXTCFDMA: db "XTCF DMA",NULL
292g_szValueCfgDeviceJrIdeIsa: db "JR-ISA",NULL
293g_szValueCfgDeviceADP50L: db "ADP50L",NULL
294g_szValueCfgDeviceSerial: db "Serial",NULL
295
296g_szSerialCOMChoice: db "COM1 - address 3F8h",LF
297 db "COM2 - address 2F8h",LF
298 db "COM3 - address 3E8h",LF
299 db "COM4 - address 2E8h",LF
300 db "COM5 - address 2F0h",LF
301 db "COM6 - address 3E0h",LF
302 db "COM7 - address 2E0h",LF
303 db "COM8 - address 260h",LF
304 db "COM9 - address 368h",LF
305 db "COMA - address 268h",LF
306 db "COMB - address 360h",LF
307 db "COMC - address 270h",LF
308 db "COMx - Custom address",NULL
309
310g_szValueCfgCOM1: db "COM1",NULL
311g_szValueCfgCOM2: db "COM2",NULL
312g_szValueCfgCOM3: db "COM3",NULL
313g_szValueCfgCOM4: db "COM4",NULL
314g_szValueCfgCOM5: db "COM5",NULL
315g_szValueCfgCOM6: db "COM6",NULL
316g_szValueCfgCOM7: db "COM7",NULL
317g_szValueCfgCOM8: db "COM8",NULL
318g_szValueCfgCOM9: db "COM9",NULL
319g_szValueCfgCOMA: db "COMA",NULL
320g_szValueCfgCOMB: db "COMB",NULL
321g_szValueCfgCOMC: db "COMC",NULL
322g_szValueCfgCOMx: db "Custom",NULL
323
324g_szSerialBaudChoice: db "115.2K baud",LF
325 db "57.6K baud",LF
326 db "38.4K baud",LF
327 db "28.8K baud",LF
328 db "19.2K baud",LF
329 db "9600 baud",LF
330 db "4800 baud",LF
331 db "2400 baud",NULL
332
333g_szValueCfgBaud115_2: db "115.2K",NULL
334g_szValueCfgBaud57_6: db "57.6K",NULL
335g_szValueCfgBaud38_4: db "38.4K",NULL
336g_szValueCfgBaud28_8: db "28.8K",NULL
337g_szValueCfgBaud19_2: db "19.2K",NULL
338g_szValueCfgBaud9600: db "9600",NULL
339g_szValueCfgBaud4800: db "4800",NULL
340g_szValueCfgBaud2400: db "2400",NULL
341
342
343; Strings for DRVPARAMS menu
344g_szItemDrvBackToIde: db "Back to IDE Controller Menu",NULL
345g_szItemDrvBlockMode: db "Block Mode Transfers",NULL
346g_szItemDrvXlateMode: db "CHS translation method",NULL
347g_szItemDrvWriteCache: db "Internal Write Cache",NULL
348g_szItemDrvUserCHS: db "User specified CHS",NULL
349g_szItemDrvCyls: db "Cylinders",NULL
350g_szItemDrvHeads: db "Heads",NULL
351g_szItemDrvSect: db "Sectors per track",NULL
352g_szItemDrvUserLBA: db "User specified LBA",NULL
353g_szItemDrvLbaSectors: db "Millions of sectors",NULL
354
355g_szDlgDrvBlockMode: db "Enable Block Mode Transfers?",NULL
356g_szDlgDrvXlateMode: db "Select P-CHS to L-CHS translation method.",NULL
357g_szDlgDrvWriteCache: db "Select hard drive internal write cache settings.",NULL
358g_szDlgDrvUserCHS: db "Specify (P-)CHS parameters manually?",NULL
359g_szDlgDrvCyls: db "Enter number of P-CHS cylinders (1...16383).",NULL
360g_szDlgDrvHeads: db "Enter number of P-CHS heads (1...16).",NULL
361g_szDlgDrvSect: db "Enter number of sectors per track (1...63).",NULL
362g_szDlgDrvUserLBA: db "Limit drive capacity?",NULL
363g_szDlgDrvLbaSectors: db "Enter maximum capacity in millions of sectors (16...256).",NULL
364
365g_szNfoDrvBlockMode: db "Transfer multiple sectors per data request.",NULL
366g_szNfoDrvXlateMode: db "P-CHS to L-CHS translation method.",NULL
367g_szNfoDrvWriteCache: db "Hard Drive Internal Write Cache settings (WARNING!).",NULL
368g_szNfoDrvUserCHS: db "Specify (P-)CHS parameters manually instead of autodetecting them.",NULL
369g_szNfoDrvCyls: db "Number of user specified P-CHS cylinders.",NULL
370g_szNfoDrvHeads: db "Number of user specified P-CHS heads.",NULL
371g_szNfoDrvSect: db "Number of user specified P-CHS sectors per track.",NULL
372g_szNfoDrvUserLBA: db "Limit drive capacity to fix compatibility problems with Windows 9x.",NULL
373g_szNfoDrvLbaSectors: db "Millions of sectors (1024*1024). 1M sectors = 512 MiB. Recommended limits are 64 for Windows 95, 128 for Windows 98 and 256 for Windows ME (and 98 with updated fdisk).",NULL
374
375g_szHelpDrvBlockMode: db "Block Mode will speed up transfers since multiple sectors can be transferred before waiting next data request."
376 db " Normally Block Mode should always be kept enabled but there is at"
377 db " least one drive with buggy Block Mode implementation.",NULL
378
379g_szHelpDrvWriteCache: db "Modern Hard Drives have a large amount of internal write cache."
380 db " The cache will speed up writes since the drive can free the bus right after data has been written to cache."
381 db " The drive then starts to write the data from cache to disk by itself."
382 db " This can be dangerous since all unwritten data in cache is lost if power is turned off or the system is reset."
383 db " Modern operating systems will flush the cache when user shuts down the system."
384 db " DOS does not have that sort of protection so it is up to the user to make sure cache is flushed."
385 db " WARNING!!! Write cache should be left disabled.",NULL
386
387g_szHelpDrvUserCHS: db "Specify (P-)CHS parameters manually instead of autodetecting them."
388 db " This can be used to limit drive size for old operating systems that do not support large hard disks."
389 db " Some early IDE drives have buggy autodetection so they require CHS to be specified manually."
390 db " Limiting Cylinders will work for all drives but drives may not accept all values for Heads and Sectors per Track.",NULL
391
392g_szHelpDrvUserLBA: db "Limit drive size to X million sectors for EBIOS functions. This option is useful to"
393 db " prevent large drive compatibility problems with MS-DOS 7.x (Windows 95 and 98).",NULL
394
395g_szMultichoiseXlateMode:
396 db "NORMAL",LF
397 db "LARGE",LF
398 db "Assisted LBA",LF
399 db "Autodetect",NULL
400
401g_szValueDrvXlateNormal:db "NORMAL",NULL
402g_szValueDrvXlateLarge: db "LARGE",NULL
403g_szValueDrvXlateLBA: db "LBA",NULL
404g_szValueDrvXlateAuto: db "Auto",NULL
405
406g_szMultichoiseWrCache: db "Drive Default",LF
407 db "Disable Write Cache",LF
408 db "Enable Write Cache",NULL
409
410g_szValueDrvWrCaDis: db "Disabled",NULL
411g_szValueDrvWrCaEn: db "Enabled",NULL
412
413
414; Strings for boot settings menu
415g_szItemBootTimeout: db "Selection timeout",NULL
416g_szItemBootDrive: db "Default boot drive",NULL
417g_szItemBootDispMode: db "Display Mode",NULL
418g_szItemBootFloppyDrvs: db "Number of Floppy Drives",NULL
419g_szItemSerialDetect: db "Scan for Serial Drives",NULL
420
421g_szDlgBootTimeout: db "Enter Boot Menu selection timeout in BIOS timer ticks (2...1092).",NULL
422g_szDlgBootDrive: db "Enter default drive number (0xh for Floppy Drives, 8xh for Hard Disks).",NULL
423g_szDlgBootDispMode: db "Select display mode.",NULL
424g_szDlgBootFloppyDrvs: db "Select number of Floppy Drives in system.",NULL
425g_szDlgSerialDetect: db "Scan for serial drives?",NULL
426
427g_szNfoBootTimeout: db "Menu item selection timeout in BIOS timer ticks. 1 tick = 54.9 ms.",NULL
428g_szNfoBootDrive: db "Default boot drive.",NULL
429g_szNfoDispMode: db "Display mode to set when booting.",NULL
430g_szNfoBootFloppyDrvs: db "Number of Floppy Drives in system.",NULL
431g_szNfoSerialDetect: db "Scans all standard COM ports for serial drives."
432 db " This can also be invoked by holding down ALT at the end of normal drive detection.",NULL
433
434g_szHelpBootTimeout: db "Boot Menu selection timeout in BIOS timer ticks (1 second = 18.2 ticks)."
435 db " When timer goes to zero, currently selected drive will be booted automatically."
436 db " Timeout can be disabled by setting this to 0.",NULL
437
438g_szHelpBootDrive: db "Drive to be set selected by default when Boot Menu is displayed.",NULL
439
440g_szHelpBootFloppyDrvs: db "Detecting the correct number of floppy drives might fail when using a floppy controller with its own BIOS."
441 db " A minimum number of floppy drives can be specified to force non-detected drives to appear on boot menu.",NULL
442
443g_szHelpSerialDetect: db "Set to Yes, at the end of normal drive detection, COM ports 1-7 (in reverse order) will be scanned for a connection"
444 db " to a serial drive server. This option provides flexibility with the COM port and baud rate to be used,"
445 db " it need not be configured ahead of time, but at the expense of a slower boot process."
446 db " Even when this option is set to No, this functionality can still be invoked by holding down the ALT key at the end"
447 db " of normal drive detection. Note that if any serial drives are detected during the normal drive detection,"
448 db " no scan will take place (to avoid finding the same drive twice).",NULL
449
450g_szMultichoiceBootDispMode: db "Default",LF
451 db "40x25 Black & White",LF
452 db "40x25 Color",LF
453 db "80x25 Black & White",LF
454 db "80x25 Color",LF
455 db "80x25 Monochrome",NULL
456
457g_szValueBootDispModeDefault: db "Default",NULL
458g_szValueBootDispModeBW40: db "BW40",NULL
459g_szValueBootDispModeCO40: db "CO40",NULL
460g_szValueBootDispModeBW80: db "BW80",NULL
461g_szValueBootDispModeCO80: db "CO80",NULL
462g_szValueBootDispModeMono: db "Mono",NULL
463
464g_szMultichoiceBootFloppyDrvs: db "Autodetect",LF
465 db "1",LF
466 db "2",LF
467 db "3",LF
468g_szValueBootFloppyDrvs4: db "4",NULL
469g_szValueBootFloppyDrvs3: db "3",NULL
470g_szValueBootFloppyDrvs2: db "2",NULL
471g_szValueBootFloppyDrvs1: db "1",NULL
472g_szValueBootFloppyDrvsAuto: db "Auto",NULL
473
474
475; Strings for Flash menu
476g_szItemFlashStart: db "Start flashing",NULL
477g_szItemFlashEepromType:db "EEPROM type",NULL
478g_szItemFlashSDP: db "SDP command",NULL
479g_szItemFlashAddr: db "EEPROM address",NULL
480g_szItemFlashPageSize: db "Page size",NULL
481g_szItemFlashChecksum: db "Generate checksum byte",NULL
482
483g_szDlgFlashEepromType: db "Select EEPROM type.",NULL
484g_szDlgFlashSDP: db "Select Software Data Protection command.",NULL
485g_szDlgFlashAddr: db "Enter segment address where EEPROM is located.",NULL
486g_szDlgFlashPageSize: db "Select write page size.",NULL
487g_szDlgFlashChecksum: db "Generate checksum byte to the end of BIOS image?",NULL
488
489g_szNfoFlashEepromType: db "EEPROM type.",NULL
490g_szNfoFlashStart: db "Writes BIOS to EEPROM.",NULL
491g_szNfoFlashSDP: db "Software Data Protection command.",NULL
492g_szNfoFlashAddr: db "Address (segment) where EEPROM is located.",NULL
493g_szNfoFlashPageSize: db "Number of bytes to write before delay.",NULL
494g_szNfoFlashChecksum: db "Generate checksum byte to the end of BIOS image.",NULL
495
496g_szHelpFlashSDP: db "Software Data Protection Command:",LF
497 db "None = Do not use Software Data Protection. Meant for EEPROMs that do not support SDP.",LF,LF
498 db "Enable = Write protects the EEPROM after flashing."
499 db " Software Data Protection should always be enabled if EEPROM supports it.",LF,LF
500 db "Disable = Disables Software Data Protection after flashing.",NULL
501
502g_szHelpFlashPageSize: db "Larger page size will improve write performance but not all EEPROMs support large pages or page writing at all."
503 db " Byte writing mode will be used when page size is set to 1. Byte writing mode is supported by all EEPROMs."
504 db " Large pages cannot be flashed with slow CPUs.",NULL
505
506g_szHelpFlashChecksum: db "PC BIOSes require a checksum byte at the end of expansion card BIOS ROMs."
507 db " You might not want to generate checksum byte when flashing some other images than XTIDE Universal BIOS.",NULL
508
509g_szMultichoiceEepromType:
510 db "2816 (2 kiB)",LF
511 db "2864 (8 kiB)",LF
512 db "2864 mod (8 kiB)",LF
513 db "28256 (32 kiB)",LF
514 db "28512 (64 kiB)",NULL
515g_szValueFlash2816: db "2816",NULL
516g_szValueFlash2864: db "2864",NULL
517g_szValueFlash2864Mod: db "2864mod",NULL
518g_szValueFlash28256: db "28256",NULL
519g_szValueFlash28512: db "28512",NULL
520
521g_szMultichoiceSdpCommand:
522 db "None",LF
523 db "Enable",LF
524g_szValueFlashDisable: db "Disable",NULL
525g_szValueFlashEnable: db "Enable",NULL
526g_szValueFlashNone: db "None",NULL
527
528g_szMultichoicePageSize:
529 db "1 byte",LF
530 db "2 bytes",LF
531 db "4 bytes",LF
532 db "8 bytes",LF
533 db "16 bytes",LF
534 db "32 bytes",LF
535g_szValueFlash64bytes: db "64 bytes",NULL
536g_szValueFlash32bytes: db "32 bytes",NULL
537g_szValueFlash16bytes: db "16 bytes",NULL
538g_szValueFlash8bytes: db "8 bytes",NULL
539g_szValueFlash4bytes: db "4 bytes",NULL
540g_szValueFlash2bytes: db "2 bytes",NULL
541g_szValueFlash1byte: db "1 byte",NULL
542
543g_szSelectionTimeout: db DOUBLE_BOTTOM_LEFT_CORNER,DOUBLE_LEFT_HORIZONTAL_TO_SINGLE_VERTICAL,"%ASelection in %2u s",NULL
544g_szDashForZero: db "- ",NULL
545g_szValueUnknownError: db "Error!",NULL
546
Note: See TracBrowser for help on using the repository browser.