source: xtideuniversalbios/trunk/XTIDE_Universal_BIOS_Configurator_v2/Src/AutoConfigure.asm@ 600

Last change on this file since 600 was 592, checked in by Krister Nordvall, 6 years ago

Changes:

  • The problem with NASM in the previous revision (r591) has been fixed.
  • The colors used by the boot menu and hotkey bar can now be customized by selecting one of a number of pre-defined color themes. Suggestions for additional themes are more than welcome!
  • Large builds are now 10 KB. Small builds are still 8 KB with the exception of the Tiny build which is now 4 KB. In other words, builds are now as small as possible to make it easier to combine them with other BIOSes.
  • Added code to the library to improve drive error handling. XTIDECFG can now handle "Drive Not Ready" errors.
  • Fixed a couple of potential bugs in AtaID.asm (AtaID_GetMaxPioModeToAXandMinCycleTimeToCX); 1) ATA1.bPioMode was treated as a WORD variable. 2) ATA2.bPIOSupp was assumed to be non-zero which would result in PIO mode 3 being returned if the assumption was wrong.
  • Made the same changes in the equivalent function used by BIOSDRVS (DisplayPioModeInformationUsingAtaInfoFromDSBX in AtaInfo.asm).
  • Fixed a bug from r587 in PDC20x30.asm in PDC20x30_GetMaxPioModeToALandMinPioCycleTimeToBX.
  • Fixed a bug from r523 in XTIDECFG where Auto Configure would only set the IRQ on one IDE interface on AT-builds.
  • XTIDECFG will now restore the default settings for the "Serial port virtual device" when reselecting it in the list of device types. This makes it behave consistently for all device types.
  • The eAAM macro is now used regardless if USE_UNDOC_INTEL is defined or not because it is apparently supported on all processors including the NEC V20/V30 CPUs.
  • Renamed the EXCLUDE_FROM_XTIDE_UNIVERSAL_BIOS define to EXCLUDE_FROM_XUB.
  • Added a define to exclude unused library code from BIOSDRVS (EXCLUDE_FROM_BIOSDRVS). This makes it a lot smaller than in previous revisions.
  • All unnecessary CLD-instructions are now under a new define 'CLD_NEEDED' which is only enabled for the BIOS. It is disabled for XTIDECFG and BIOSDRVS but can be enabled if needed by adding this define to the respective makefile. This change was made because these unnecessary instructions are wasteful and should never be needed. In fact, they only serve to hide bugs (in other peoples code) which I strongly believe should be avoided. I recommend people making their own BIOSes from source to not use this define as it's extremely unlikely to be needed.
  • Updated the copyright info in SerDrive and changed an URL to point to the new site.
  • Updated the copyright info and version number in BIOSDRVS.
  • Updated the copyright info in XTIDECFG.
  • Optimizations in general.
File size: 6.3 KB
Line 
1; Project name : XTIDE Universal BIOS Configurator v2
2; Description : Functions to automatically configure XTIDE
3; Universal BIOS for current system.
4
5;
6; XTIDE Universal BIOS and Associated Tools
7; Copyright (C) 2009-2010 by Tomi Tilli, 2011-2013 by XTIDE Universal BIOS Team.
8;
9; This program is free software; you can redistribute it and/or modify
10; it under the terms of the GNU General Public License as published by
11; the Free Software Foundation; either version 2 of the License, or
12; (at your option) any later version.
13;
14; This program is distributed in the hope that it will be useful,
15; but WITHOUT ANY WARRANTY; without even the implied warranty of
16; MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
17; GNU General Public License for more details.
18; Visit http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
19;
20
21; Section containing code
22SECTION .text
23
24
25;--------------------------------------------------------------------
26; AutoConfigure_ForThisSystem
27; MENUITEM activation function (.fnActivate)
28; Parameters:
29; SS:BP: Ptr to MENU
30; Returns:
31; Nothing
32; Corrupts registers:
33; All, except segments
34;--------------------------------------------------------------------
35ALIGN JUMP_ALIGN
36AutoConfigure_ForThisSystem:
37 push es
38 push ds
39
40 call Buffers_GetFileBufferToESDI ; ROMVARS now in ES:DI
41 push es
42 pop ds ; ROMVARS now in DS:DI
43 call ResetIdevarsToDefaultValues
44 call DetectIdePortsAndDevices
45 call EnableInterruptsForAllStandardControllers
46 call StoreAndDisplayNumberOfControllers
47
48 pop ds
49 pop es
50 ret
51
52
53;--------------------------------------------------------------------
54; ResetIdevarsToDefaultValues
55; Parameters:
56; DS:DI: Ptr to ROMVARS
57; ES:DI: Ptr to ROMVARS
58; Returns:
59; Nothing
60; Corrupts registers:
61; AX, CX
62;--------------------------------------------------------------------
63ALIGN JUMP_ALIGN
64ResetIdevarsToDefaultValues:
65 push di
66 add di, BYTE ROMVARS.ideVarsBegin
67 mov cx, ROMVARS.ideVarsEnd - ROMVARS.ideVarsBegin
68 call Memory_ZeroESDIwithSizeInCX ; Never clears ROMVARS.ideVarsSerialAuto
69 pop di
70
71 ; Set default values (other than zero)
72 mov ax, DISABLE_WRITE_CACHE | (TRANSLATEMODE_AUTO<<TRANSLATEMODE_FIELD_POSITION) | FLG_DRVPARAMS_BLOCKMODE
73 mov [di+ROMVARS.ideVars0+IDEVARS.drvParamsMaster+DRVPARAMS.wFlags], ax
74 mov [di+ROMVARS.ideVars0+IDEVARS.drvParamsSlave+DRVPARAMS.wFlags], ax
75
76 mov [di+ROMVARS.ideVars1+IDEVARS.drvParamsMaster+DRVPARAMS.wFlags], ax
77 mov [di+ROMVARS.ideVars1+IDEVARS.drvParamsSlave+DRVPARAMS.wFlags], ax
78
79 mov [di+ROMVARS.ideVars2+IDEVARS.drvParamsMaster+DRVPARAMS.wFlags], ax
80 mov [di+ROMVARS.ideVars2+IDEVARS.drvParamsSlave+DRVPARAMS.wFlags], ax
81
82 mov [di+ROMVARS.ideVars3+IDEVARS.drvParamsMaster+DRVPARAMS.wFlags], ax
83 mov [di+ROMVARS.ideVars3+IDEVARS.drvParamsSlave+DRVPARAMS.wFlags], ax
84 ret
85
86
87;--------------------------------------------------------------------
88; DetectIdePortsAndDevices
89; Parameters:
90; DS:DI: Ptr to ROMVARS
91; Returns:
92; CX: Number of controllers detected
93; Corrupts registers:
94; AX, BX, DX, SI
95;--------------------------------------------------------------------
96ALIGN JUMP_ALIGN
97DetectIdePortsAndDevices:
98 xor cx, cx ; Number of devices found
99 xor dx, dx ; IDE_PORT_TO_START_DETECTION
100 lea si, [di+ROMVARS.ideVarsBegin] ; DS:SI points to first IDEVARS
101
102.DetectFromNextPort:
103 call IdeAutodetect_IncrementDXtoNextIdeBasePort
104 jz SHORT .AllPortsAlreadyDetected
105 push si
106 call IdeAutodetect_DetectIdeDeviceFromPortDXAndReturnControlBlockInSI
107 mov bx, si
108 pop si
109 jc SHORT .DetectFromNextPort
110
111 ; Device found from port DX, Device Type returned in AL
112 inc cx ; Increment number of controllers found
113 mov [si+IDEVARS.wBasePort], dx
114 mov [si+IDEVARS.wControlBlockPort], bx
115 mov [si+IDEVARS.bDevice], al
116
117 ; Point to next IDEVARS
118 add si, IDEVARS_size
119 cmp si, ROMVARS.ideVars3
120 jbe SHORT .DetectFromNextPort
121.AllPortsAlreadyDetected:
122 ret
123
124
125;--------------------------------------------------------------------
126; EnableInterruptsForAllStandardControllers
127; Parameters:
128; DS:DI: Ptr to ROMVARS
129; CX: Number of controllers detected
130; Returns:
131; Nothing
132; Corrupts registers:
133; AX
134;--------------------------------------------------------------------
135ALIGN JUMP_ALIGN
136EnableInterruptsForAllStandardControllers:
137 jcxz .NoControllersDetected
138 call Buffers_IsXTbuildLoaded
139 je SHORT .DoNotEnableIRQforXTbuilds
140 push di
141 push cx
142
143 add di, BYTE ROMVARS.ideVars0 ; DS:DI now points first IDEVARS
144.CheckNextController:
145 mov al, 14
146 cmp WORD [di+IDEVARS.wBasePort], DEVICE_ATA_PRIMARY_PORT
147 je SHORT .EnableIrqAL
148
149 inc ax ; 15
150 cmp WORD [di+IDEVARS.wBasePort], DEVICE_ATA_SECONDARY_PORT
151
152%if 0
153 je SHORT .EnableIrqAL
154
155 ; Defaults on the GSI Inc. Model 2C EIDE controller
156 mov al, 11
157 cmp WORD [di+IDEVARS.wBasePort], DEVICE_ATA_TERTIARY_PORT
158 je SHORT .EnableIrqAL
159
160 dec ax ; 10
161 cmp WORD [di+IDEVARS.wBasePort], DEVICE_ATA_QUATERNARY_PORT
162%endif
163
164 jne SHORT .DoNotEnableIRQ
165
166.EnableIrqAL:
167 mov [di+IDEVARS.bIRQ], al
168.DoNotEnableIRQ:
169 add di, IDEVARS_size
170 loop .CheckNextController
171 pop cx
172 pop di
173.DoNotEnableIRQforXTbuilds:
174.NoControllersDetected:
175 ret
176
177
178;--------------------------------------------------------------------
179; StoreAndDisplayNumberOfControllers
180; Parameters:
181; CX: Number of controllers detected
182; DS:DI: Ptr to ROMVARS
183; SS:BP: Ptr to MENU
184; Returns:
185; Nothing
186; Corrupts registers:
187; AX, BX, DX, DI, SI, DS, ES
188;--------------------------------------------------------------------
189ALIGN JUMP_ALIGN
190StoreAndDisplayNumberOfControllers:
191 xor ax, ax
192 or al, cl
193 jnz SHORT .AtLeastOneController
194 inc ax ; Cannot store zero
195.AtLeastOneController:
196 test BYTE [di+ROMVARS.wFlags], FLG_ROMVARS_FULLMODE
197 jnz SHORT .FullModeSoNoNeedToLimit
198 MIN_U al, MAX_LITE_MODE_CONTROLLERS
199.FullModeSoNoNeedToLimit:
200
201 ; Store number of IDE Controllers. This will also modify
202 ; menu and set unsaved changes flag.
203 push cs
204 pop ds
205 mov si, g_MenuitemConfigurationIdeControllers
206 call Menuitem_StoreValueFromAXtoMenuitemInDSSI
207
208 ; Display results (should be changed to proper string formatting)
209 add cl, '0'
210 mov [cs:g_bControllersDetected], cl
211 mov dx, g_szDlgAutoConfigure
212 jmp Dialogs_DisplayNotificationFromCSDX
Note: See TracBrowser for help on using the repository browser.