source: xtideuniversalbios/trunk/XTIDE_Universal_BIOS/makefile@ 407

Last change on this file since 407 was 400, checked in by aitotat@…, 13 years ago

Changes to XTIDE Universal BIOS:

  • Moved 8-bit device support to MODULE_8BIT_IDE.
  • JR-IDE/ISA support requires a lot less bytes.
  • AT builds now always use full operating mode.
File size: 10.1 KB
Line 
1##################################################################################################
2# Makefile to build XTIDE Universal BIOS. #
3# #
4# Valid makefile targets are: #
5# all Removes existing files and builds binary files in \Build #
6# small Builds 8 kiB binaries only (without checksum) #
7# large Builds 15 kiB binaries only (without checksum) #
8# clean Removes all files from \Build #
9# checksum* Builds all and then generates checksum byte to all binary files #
10# strings* Compress src\Strings.asm to src\StringsCompressed.asm #
11# #
12# * at the end of target name means that Perl is required for the job. #
13# Build directory must be created manually if it does not exist. #
14# #
15# #
16# Following modules can be included or excluded: #
17# MODULE_8BIT_IDE Support for 8-BIT IDE cards like XTIDE #
18# MODULE_JRIDE Support for JR-IDE/ISA #
19# MODULE_ADVANCED_ATA Native support for some VLB IDE controllers #
20# MODULE_BOOT_MENU Boot Menu for selection of drive to boot from #
21# MODULE_EBIOS Enhanced functions for accessing drives over 8.4 GB #
22# MODULE_HOTKEYS Hotkey Bar to boot from any drive #
23# MODULE_IRQ IDE IRQ support #
24# MODULE_SERIAL Virtual hard disks using serial port #
25# MODULE_SERIAL_FLOPPY Virtual floppy drives using serial port (requires MODULE_SERIAL) #
26# MODULE_STRINGS_COMPRESSED Use compressed strings to save space #
27# MODULE_FEATURE_SETS Power Management support #
28# #
29# Not modules but these affect the assembly: #
30# ELIMINATE_CGA_SNOW Prevents CGA snowing at the cost of a few bytes #
31# USE_186 Use instructions supported by 80188/80186 and V20/V30 and later #
32# USE_286 Use instructions supported by 286 and later #
33# USE_386 Use instructions supported by 386 and later #
34# USE_AT Use features supported on AT and later systems (not available on XT) #
35# #
36##################################################################################################
37
38###########################################
39# Source files and destination executable #
40###########################################
41
42# Assembly source code file (*.asm):
43SRC_ASM = Src/Main.asm
44
45# Program executable file name without extension:
46PROG = ide
47
48
49#######################################
50# Destination and include directories #
51#######################################
52
53# Directory where binary file will be compiled to
54BUILD_DIR = Build
55
56# Subdirectories where included files are:
57HEADERS = Inc/
58HEADERS += Inc/Controllers/
59HEADERS += Src/
60HEADERS += Src/Handlers/
61HEADERS += Src/Handlers/Int13h/
62HEADERS += Src/Handlers/Int13h/EBIOS/
63HEADERS += Src/Handlers/Int13h/Tools/
64HEADERS += Src/Handlers/Int19h/
65HEADERS += Src/Device/
66HEADERS += Src/Device/IDE/
67HEADERS += Src/Device/MemoryMappedIDE/
68HEADERS += Src/Device/Serial/
69HEADERS += Src/Initialization/
70HEADERS += Src/Initialization/AdvancedAta/
71HEADERS += Src/Menus/
72HEADERS += Src/Menus/BootMenu/
73HEADERS += Src/Libraries/
74HEADERS += Src/VariablesAndDPTs/
75
76# Subdirectories where library files are:
77LIBS = ../Assembly_Library/Inc/
78LIBS += ../Assembly_Library/Src/
79LIBS += ../Assembly_Library/Src/Display/
80LIBS += ../Assembly_Library/Src/File/
81LIBS += ../Assembly_Library/Src/Keyboard/
82LIBS += ../Assembly_Library/Src/Menu/
83LIBS += ../Assembly_Library/Src/Menu/Dialog/
84LIBS += ../Assembly_Library/Src/String/
85LIBS += ../Assembly_Library/Src/Time/
86LIBS += ../Assembly_Library/Src/Util/
87LIBS += ../Assembly_Library/Src/Serial/
88LIBS += ../XTIDE_Universal_BIOS/Inc/
89HEADERS += $(LIBS)
90
91
92#################################################################
93# Assembler preprocessor defines. #
94#################################################################
95DEFINES_COMMON = MODULE_STRINGS_COMPRESSED MODULE_HOTKEYS MODULE_EBIOS MODULE_FEATURE_SETS
96DEFINES_COMMON_LARGE = MODULE_BOOT_MENU MODULE_SERIAL MODULE_SERIAL_FLOPPY
97
98DEFINES_XT = $(DEFINES_COMMON) ELIMINATE_CGA_SNOW MODULE_8BIT_IDE MODULE_JRIDE MODULE_SERIAL MODULE_SERIAL_FLOPPY
99DEFINES_XTPLUS = $(DEFINES_COMMON) $(DEFINES_XT) USE_186
100DEFINES_AT = $(DEFINES_COMMON) USE_AT USE_286 MODULE_IRQ MODULE_SERIAL MODULE_SERIAL_FLOPPY MODULE_ADVANCED_ATA
101
102DEFINES_XT_LARGE = $(DEFINES_XT) $(DEFINES_COMMON_LARGE)
103DEFINES_XTPLUS_LARGE = $(DEFINES_XTPLUS) $(DEFINES_COMMON_LARGE)
104DEFINES_AT_LARGE = $(DEFINES_AT) $(DEFINES_COMMON_LARGE)
105
106DEFINES_XT_TINY = MODULE_STRINGS_COMPRESSED MODULE_8BIT_IDE
107DEFINES_386_8K = $(DEFINES_AT) USE_386
108
109
110###################
111# Other variables #
112###################
113
114# Target size of the ROM, used in main.asm for number of 512B blocks and by checksum Perl script below
115ROMSIZE = 8192
116ROMSIZE_LARGE = 15360
117
118# Add -D in front of every preprocessor define declaration
119DEFS_XT = $(DEFINES_XT:%=-D%) -DROMSIZE=$(ROMSIZE)
120DEFS_XTPLUS = $(DEFINES_XTPLUS:%=-D%) -DROMSIZE=$(ROMSIZE)
121DEFS_AT = $(DEFINES_AT:%=-D%) -DROMSIZE=$(ROMSIZE)
122DEFS_XT_LARGE = $(DEFINES_XT_LARGE:%=-D%) -DROMSIZE=$(ROMSIZE_LARGE)
123DEFS_XTPLUS_LARGE = $(DEFINES_XTPLUS_LARGE:%=-D%) -DROMSIZE=$(ROMSIZE_LARGE)
124DEFS_AT_LARGE = $(DEFINES_AT_LARGE:%=-D%) -DROMSIZE=$(ROMSIZE_LARGE)
125DEFS_XT_TINY = $(DEFINES_XT_TINY:%=-D%) -DROMSIZE=$(ROMSIZE)
126DEFS_386_8K = $(DEFINES_386_8K:%=-D%) -DROMSIZE=$(ROMSIZE)
127
128# Add -I in front of all header directories
129IHEADERS = $(HEADERS:%=-I%)
130
131# Path + target file to be built
132TARGET = $(BUILD_DIR)/$(PROG)
133
134#########################
135# Compilers and linkers #
136#########################
137
138# Make
139MAKE = mingw32-make.exe
140
141# Assembler
142AS = nasm.exe
143
144# use this command to erase files.
145RM = -del /Q
146
147
148#############################
149# Compiler and linker flags #
150#############################
151
152# Assembly compiler flags
153ASFLAGS = -f bin # Produce binary object files
154ASFLAGS += $(IHEADERS) # Set header file directory paths
155ASFLAGS += -Worphan-labels # Warn about labels without colon
156ASFLAGS += -Ox # Optimize operands to their shortest forms
157
158
159############################################
160# Build process. Actual work is done here. #
161############################################
162
163all: clean small large
164 @echo All done!
165
166small: xt_tiny xt xtplus at 386_8k
167 @echo All 8 kiB binaries built!
168
169large: xt_large xtplus_large at_large
170 @echo All 15 kiB binaries built!
171
172at:
173 @$(AS) "$(SRC_ASM)" $(ASFLAGS) $(DEFS_AT) -l"$(TARGET)_at.lst" -o"$(TARGET)_at.bin"
174 @echo * 8k AT version "$(TARGET)_at.bin" built.
175
176at_large:
177 @$(AS) "$(SRC_ASM)" $(ASFLAGS) $(DEFS_AT_LARGE) -l"$(TARGET)_atl.lst" -o"$(TARGET)_atl.bin"
178 @echo *15k AT version "$(TARGET)_atl.bin" built.
179
180xtplus:
181 @$(AS) "$(SRC_ASM)" $(ASFLAGS) $(DEFS_XTPLUS) -l"$(TARGET)_xtp.lst" -o"$(TARGET)_xtp.bin"
182 @echo * 8k XT Plus version "$(TARGET)_xtp.bin" built.
183
184xtplus_large:
185 @$(AS) "$(SRC_ASM)" $(ASFLAGS) $(DEFS_XTPLUS_LARGE) -l"$(TARGET)_xtpl.lst" -o"$(TARGET)_xtpl.bin"
186 @echo *15k XT Plus version "$(TARGET)_xtpl.bin" built.
187
188xt:
189 @$(AS) "$(SRC_ASM)" $(ASFLAGS) $(DEFS_XT) -l"$(TARGET)_xt.lst" -o"$(TARGET)_xt.bin"
190 @echo * 8k XT version "$(TARGET)_xt.bin" built.
191
192xt_large:
193 @$(AS) "$(SRC_ASM)" $(ASFLAGS) $(DEFS_XT_LARGE) -l"$(TARGET)_xtl.lst" -o"$(TARGET)_xtl.bin"
194 @echo *15k XT version "$(TARGET)_xtl.bin" built.
195
196xt_tiny:
197 @$(AS) "$(SRC_ASM)" $(ASFLAGS) $(DEFS_XT_TINY) -l"$(TARGET)_tiny.lst" -o"$(TARGET)_tiny.bin"
198 @echo * Tiny XT version "$(TARGET)_tiny.bin" built.
199
200386_8k:
201 @$(AS) "$(SRC_ASM)" $(ASFLAGS) $(DEFS_386_8K) -l"$(TARGET)_386.lst" -o"$(TARGET)_386.bin"
202 @echo * 8k 386 version "$(TARGET)_386.bin" built.
203
204strings: src\Strings.asm
205 @$(AS) src\Strings.asm $(ASFLAGS) $(DEFS_XT) -DCHECK_FOR_UNUSED_ENTRYPOINTS -DMODULE_STRINGS_COMPRESSED_PRECOMPRESS -o build\Strings.bin -l build\StringsPrecompress.lst
206 @perl ..\tools\StringsCompress.pl < build\StringsPrecompress.lst > src\StringsCompressed.asm
207 @echo StringsCompressed.asm updated!
208
209clean:
210 @$(RM) $(BUILD_DIR)\*.*
211 @echo Deleted "(*.*)" from "$(BUILD_DIR)/"
212
213checksum: all
214 @perl ..\tools\checksum.pl $(TARGET)_tiny.bin $(ROMSIZE)
215 @perl ..\tools\checksum.pl $(TARGET)_xt.bin $(ROMSIZE)
216 @perl ..\tools\checksum.pl $(TARGET)_xtp.bin $(ROMSIZE)
217 @perl ..\tools\checksum.pl $(TARGET)_at.bin $(ROMSIZE)
218 @perl ..\tools\checksum.pl $(TARGET)_xtl.bin $(ROMSIZE_LARGE)
219 @perl ..\tools\checksum.pl $(TARGET)_xtpl.bin $(ROMSIZE_LARGE)
220 @perl ..\tools\checksum.pl $(TARGET)_atl.bin $(ROMSIZE_LARGE)
221 @perl ..\tools\checksum.pl $(TARGET)_386.bin $(ROMSIZE)
222
223xt_unused: xt
224 @$(AS) "$(SRC_ASM)" $(ASFLAGS) $(DEFS_XT) -o"$(TARGET)_xt_unused.asm" -E -DCHECK_FOR_UNUSED_ENTRYPOINTS
225 @perl ..\tools\unused.pl $(TARGET)_xt.lst $(TARGET)_xt_unused.asm
226
Note: See TracBrowser for help on using the repository browser.