source: xtideuniversalbios/trunk/XTIDE_Universal_BIOS/makefile@ 420

Last change on this file since 420 was 417, checked in by aitotat@…, 13 years ago

Changes to XTIDE Universal BIOS:

  • AT builds now relocate INT 13h stack to top of stolen conventional memory.
  • Some small fixes here and there.
File size: 10.2 KB
RevLine 
[379]1##################################################################################################
2# Makefile to build XTIDE Universal BIOS. #
3# #
4# Valid makefile targets are: #
[389]5# all Removes existing files and builds binary files in \Build #
6# small Builds 8 kiB binaries only (without checksum) #
7# large Builds 15 kiB binaries only (without checksum) #
8# clean Removes all files from \Build #
9# checksum* Builds all and then generates checksum byte to all binary files #
10# strings* Compress src\Strings.asm to src\StringsCompressed.asm #
[379]11# #
12# * at the end of target name means that Perl is required for the job. #
13# Build directory must be created manually if it does not exist. #
14# #
15# #
16# Following modules can be included or excluded: #
[400]17# MODULE_8BIT_IDE Support for 8-BIT IDE cards like XTIDE #
18# MODULE_JRIDE Support for JR-IDE/ISA #
[379]19# MODULE_ADVANCED_ATA Native support for some VLB IDE controllers #
[380]20# MODULE_BOOT_MENU Boot Menu for selection of drive to boot from #
21# MODULE_EBIOS Enhanced functions for accessing drives over 8.4 GB #
[395]22# MODULE_HOTKEYS Hotkey Bar to boot from any drive #
[398]23# MODULE_IRQ IDE IRQ support #
[379]24# MODULE_SERIAL Virtual hard disks using serial port #
[380]25# MODULE_SERIAL_FLOPPY Virtual floppy drives using serial port (requires MODULE_SERIAL) #
26# MODULE_STRINGS_COMPRESSED Use compressed strings to save space #
[399]27# MODULE_FEATURE_SETS Power Management support #
[379]28# #
29# Not modules but these affect the assembly: #
[380]30# ELIMINATE_CGA_SNOW Prevents CGA snowing at the cost of a few bytes #
[417]31# RELOCATE_INT13H_STACK Relocates INT 13h stack to top of stolen conventional memory #
[379]32# USE_186 Use instructions supported by 80188/80186 and V20/V30 and later #
33# USE_286 Use instructions supported by 286 and later #
34# USE_386 Use instructions supported by 386 and later #
35# USE_AT Use features supported on AT and later systems (not available on XT) #
36# #
37##################################################################################################
[3]38
39###########################################
40# Source files and destination executable #
41###########################################
42
43# Assembly source code file (*.asm):
44SRC_ASM = Src/Main.asm
45
46# Program executable file name without extension:
47PROG = ide
48
49
50#######################################
51# Destination and include directories #
52#######################################
53
54# Directory where binary file will be compiled to
55BUILD_DIR = Build
56
57# Subdirectories where included files are:
58HEADERS = Inc/
[363]59HEADERS += Inc/Controllers/
[3]60HEADERS += Src/
61HEADERS += Src/Handlers/
62HEADERS += Src/Handlers/Int13h/
[165]63HEADERS += Src/Handlers/Int13h/EBIOS/
64HEADERS += Src/Handlers/Int13h/Tools/
[392]65HEADERS += Src/Handlers/Int19h/
[150]66HEADERS += Src/Device/
67HEADERS += Src/Device/IDE/
[238]68HEADERS += Src/Device/MemoryMappedIDE/
[150]69HEADERS += Src/Device/Serial/
[3]70HEADERS += Src/Initialization/
[392]71HEADERS += Src/Initialization/AdvancedAta/
72HEADERS += Src/Menus/
73HEADERS += Src/Menus/BootMenu/
[3]74HEADERS += Src/Libraries/
75HEADERS += Src/VariablesAndDPTs/
76
[88]77# Subdirectories where library files are:
78LIBS = ../Assembly_Library/Inc/
79LIBS += ../Assembly_Library/Src/
80LIBS += ../Assembly_Library/Src/Display/
81LIBS += ../Assembly_Library/Src/File/
82LIBS += ../Assembly_Library/Src/Keyboard/
83LIBS += ../Assembly_Library/Src/Menu/
84LIBS += ../Assembly_Library/Src/Menu/Dialog/
85LIBS += ../Assembly_Library/Src/String/
86LIBS += ../Assembly_Library/Src/Time/
87LIBS += ../Assembly_Library/Src/Util/
[277]88LIBS += ../Assembly_Library/Src/Serial/
[88]89LIBS += ../XTIDE_Universal_BIOS/Inc/
90HEADERS += $(LIBS)
[3]91
[88]92
[3]93#################################################################
94# Assembler preprocessor defines. #
95#################################################################
[399]96DEFINES_COMMON = MODULE_STRINGS_COMPRESSED MODULE_HOTKEYS MODULE_EBIOS MODULE_FEATURE_SETS
[400]97DEFINES_COMMON_LARGE = MODULE_BOOT_MENU MODULE_SERIAL MODULE_SERIAL_FLOPPY
[389]98
[400]99DEFINES_XT = $(DEFINES_COMMON) ELIMINATE_CGA_SNOW MODULE_8BIT_IDE MODULE_JRIDE MODULE_SERIAL MODULE_SERIAL_FLOPPY
[397]100DEFINES_XTPLUS = $(DEFINES_COMMON) $(DEFINES_XT) USE_186
[417]101DEFINES_AT = $(DEFINES_COMMON) USE_AT USE_286 RELOCATE_INT13H_STACK MODULE_IRQ MODULE_SERIAL MODULE_SERIAL_FLOPPY MODULE_ADVANCED_ATA
[389]102
[397]103DEFINES_XT_LARGE = $(DEFINES_XT) $(DEFINES_COMMON_LARGE)
104DEFINES_XTPLUS_LARGE = $(DEFINES_XTPLUS) $(DEFINES_COMMON_LARGE)
105DEFINES_AT_LARGE = $(DEFINES_AT) $(DEFINES_COMMON_LARGE)
[389]106
[400]107DEFINES_XT_TINY = MODULE_STRINGS_COMPRESSED MODULE_8BIT_IDE
[397]108DEFINES_386_8K = $(DEFINES_AT) USE_386
[3]109
110
111###################
112# Other variables #
113###################
114
[239]115# Target size of the ROM, used in main.asm for number of 512B blocks and by checksum Perl script below
116ROMSIZE = 8192
117ROMSIZE_LARGE = 15360
118
[3]119# Add -D in front of every preprocessor define declaration
[239]120DEFS_XT = $(DEFINES_XT:%=-D%) -DROMSIZE=$(ROMSIZE)
121DEFS_XTPLUS = $(DEFINES_XTPLUS:%=-D%) -DROMSIZE=$(ROMSIZE)
122DEFS_AT = $(DEFINES_AT:%=-D%) -DROMSIZE=$(ROMSIZE)
123DEFS_XT_LARGE = $(DEFINES_XT_LARGE:%=-D%) -DROMSIZE=$(ROMSIZE_LARGE)
124DEFS_XTPLUS_LARGE = $(DEFINES_XTPLUS_LARGE:%=-D%) -DROMSIZE=$(ROMSIZE_LARGE)
125DEFS_AT_LARGE = $(DEFINES_AT_LARGE:%=-D%) -DROMSIZE=$(ROMSIZE_LARGE)
[397]126DEFS_XT_TINY = $(DEFINES_XT_TINY:%=-D%) -DROMSIZE=$(ROMSIZE)
[366]127DEFS_386_8K = $(DEFINES_386_8K:%=-D%) -DROMSIZE=$(ROMSIZE)
[3]128
129# Add -I in front of all header directories
130IHEADERS = $(HEADERS:%=-I%)
131
[145]132# Path + target file to be built
[3]133TARGET = $(BUILD_DIR)/$(PROG)
134
135#########################
136# Compilers and linkers #
137#########################
138
139# Make
140MAKE = mingw32-make.exe
141
142# Assembler
[188]143AS = nasm.exe
[3]144
145# use this command to erase files.
146RM = -del /Q
147
148
149#############################
150# Compiler and linker flags #
151#############################
152
153# Assembly compiler flags
154ASFLAGS = -f bin # Produce binary object files
155ASFLAGS += $(IHEADERS) # Set header file directory paths
156ASFLAGS += -Worphan-labels # Warn about labels without colon
[379]157ASFLAGS += -Ox # Optimize operands to their shortest forms
[3]158
159
160############################################
161# Build process. Actual work is done here. #
162############################################
163
[272]164all: clean small large
[145]165 @echo All done!
[3]166
[397]167small: xt_tiny xt xtplus at 386_8k
[294]168 @echo All 8 kiB binaries built!
[272]169
[397]170large: xt_large xtplus_large at_large
[294]171 @echo All 15 kiB binaries built!
[272]172
[3]173at:
[80]174 @$(AS) "$(SRC_ASM)" $(ASFLAGS) $(DEFS_AT) -l"$(TARGET)_at.lst" -o"$(TARGET)_at.bin"
[272]175 @echo * 8k AT version "$(TARGET)_at.bin" built.
[3]176
[238]177at_large:
178 @$(AS) "$(SRC_ASM)" $(ASFLAGS) $(DEFS_AT_LARGE) -l"$(TARGET)_atl.lst" -o"$(TARGET)_atl.bin"
[272]179 @echo *15k AT version "$(TARGET)_atl.bin" built.
[238]180
[3]181xtplus:
[80]182 @$(AS) "$(SRC_ASM)" $(ASFLAGS) $(DEFS_XTPLUS) -l"$(TARGET)_xtp.lst" -o"$(TARGET)_xtp.bin"
[294]183 @echo * 8k XT Plus version "$(TARGET)_xtp.bin" built.
[3]184
[238]185xtplus_large:
186 @$(AS) "$(SRC_ASM)" $(ASFLAGS) $(DEFS_XTPLUS_LARGE) -l"$(TARGET)_xtpl.lst" -o"$(TARGET)_xtpl.bin"
[294]187 @echo *15k XT Plus version "$(TARGET)_xtpl.bin" built.
[238]188
[3]189xt:
[80]190 @$(AS) "$(SRC_ASM)" $(ASFLAGS) $(DEFS_XT) -l"$(TARGET)_xt.lst" -o"$(TARGET)_xt.bin"
[272]191 @echo * 8k XT version "$(TARGET)_xt.bin" built.
[3]192
[238]193xt_large:
194 @$(AS) "$(SRC_ASM)" $(ASFLAGS) $(DEFS_XT_LARGE) -l"$(TARGET)_xtl.lst" -o"$(TARGET)_xtl.bin"
[272]195 @echo *15k XT version "$(TARGET)_xtl.bin" built.
[277]196
[397]197xt_tiny:
198 @$(AS) "$(SRC_ASM)" $(ASFLAGS) $(DEFS_XT_TINY) -l"$(TARGET)_tiny.lst" -o"$(TARGET)_tiny.bin"
199 @echo * Tiny XT version "$(TARGET)_tiny.bin" built.
[238]200
[366]201386_8k:
202 @$(AS) "$(SRC_ASM)" $(ASFLAGS) $(DEFS_386_8K) -l"$(TARGET)_386.lst" -o"$(TARGET)_386.bin"
203 @echo * 8k 386 version "$(TARGET)_386.bin" built.
204
[322]205strings: src\Strings.asm
[415]206 @$(AS) src\Strings.asm $(ASFLAGS) $(DEFS_AT_LARGE) -DCHECK_FOR_UNUSED_ENTRYPOINTS -DMODULE_STRINGS_COMPRESSED_PRECOMPRESS -o build\Strings.bin -l build\StringsPrecompress.lst
[322]207 @perl ..\tools\StringsCompress.pl < build\StringsPrecompress.lst > src\StringsCompressed.asm
208 @echo StringsCompressed.asm updated!
[252]209
[3]210clean:
211 @$(RM) $(BUILD_DIR)\*.*
212 @echo Deleted "(*.*)" from "$(BUILD_DIR)/"
[186]213
[294]214checksum: all
[397]215 @perl ..\tools\checksum.pl $(TARGET)_tiny.bin $(ROMSIZE)
216 @perl ..\tools\checksum.pl $(TARGET)_xt.bin $(ROMSIZE)
217 @perl ..\tools\checksum.pl $(TARGET)_xtp.bin $(ROMSIZE)
218 @perl ..\tools\checksum.pl $(TARGET)_at.bin $(ROMSIZE)
219 @perl ..\tools\checksum.pl $(TARGET)_xtl.bin $(ROMSIZE_LARGE)
220 @perl ..\tools\checksum.pl $(TARGET)_xtpl.bin $(ROMSIZE_LARGE)
[240]221 @perl ..\tools\checksum.pl $(TARGET)_atl.bin $(ROMSIZE_LARGE)
[369]222 @perl ..\tools\checksum.pl $(TARGET)_386.bin $(ROMSIZE)
[203]223
[252]224xt_unused: xt
[370]225 @$(AS) "$(SRC_ASM)" $(ASFLAGS) $(DEFS_XT) -o"$(TARGET)_xt_unused.asm" -E -DCHECK_FOR_UNUSED_ENTRYPOINTS
226 @perl ..\tools\unused.pl $(TARGET)_xt.lst $(TARGET)_xt_unused.asm
[194]227
Note: See TracBrowser for help on using the repository browser.