source: xtideuniversalbios/trunk/XTIDE_Universal_BIOS/Src/Initialization/Vision.asm@ 375

; Project name  :   XTIDE Universal BIOS
; Description   :   Functions for initializing QDI Vision
;                   QD6500 and QD6580 VLB IDE Controllers.

; Section containing code
SECTION .text

;--------------------------------------------------------------------
; Vision_DetectAndReturnIDinAXandPortInDXifControllerPresent
;   Parameters:
;       Nothing
;   Returns:
;       AX:     ID WORD specific for QDI Vision Controllers
;               (AL = QD65xx Config Register contents)
;               (AH = QDI Vision Controller ID (bits 4...7))
;       DX:     Controller port (not IDE port)
;       ZF:     Set if controller found
;               Cleared if supported controller not found (AX,DX = undefined)
;   Corrupts registers:
;       Nothing
;--------------------------------------------------------------------
Vision_DetectAndReturnIDinAXandPortInDXifControllerPresent:
    ; Check QD65xx base port
    mov     dx, QD65XX_BASE_PORT
    in      al, QD65XX_BASE_PORT + QD65XX_CONFIG_REGISTER_in
    call    IsConfigRegisterWithIDinAL
    je      SHORT VisionControllerDetected

    ; Check QD65xx alternative base port
    or      dl, QD65XX_ALTERNATIVE_BASE_PORT
    in      al, QD65XX_ALTERNATIVE_BASE_PORT + QD65XX_CONFIG_REGISTER_in
    ; Fall to IsConfigRegisterWithIDinAL

;--------------------------------------------------------------------
; IsConfigRegisterWithIDinAL
;   Parameters:
;       AL:     Possible QD65xx Config Register contents
;   Returns:
;       AH      QDI Vision Controller ID or undefined
;       ZF:     Set if controller found
;               Cleared if supported controller not found (AH = undefined)
;   Corrupts registers:
;       Nothing
;--------------------------------------------------------------------
IsConfigRegisterWithIDinAL:
    mov     ah, al
    and     al, MASK_QDCONFIG_CONTROLLER_ID
    cmp     al, ID_QD6500 << 4
    je      SHORT VisionControllerDetected
    cmp     al, ID_QD6580 << 4
    je      SHORT VisionControllerDetected
    cmp     al, ID_QD6580_ALTERNATE << 4
VisionControllerDetected:
    xchg    ah, al
    ret


;--------------------------------------------------------------------
; Vision_DoesIdePortInBXbelongToControllerWithIDinAX
;   Parameters:
;       AL:     QD65xx Config Register contents
;       AH:     QDI Vision Controller ID (bits 4...7)
;       BX:     IDE Base port to check
;       DX:     Vision Controller port
;   Returns:
;       ZF:     Set if port belongs to controller
;               Cleared if port belongs to another controller
;   Corrupts registers:
;       Nothing
;--------------------------------------------------------------------
Vision_DoesIdePortInBXbelongToControllerWithIDinAX:
    cmp     ah, ID_QD6500 << 4
    je      SHORT .DoesIdePortInDXbelongToQD6500

    ; QD6580 always have Primary IDE at 1F0h
    ; Secondary IDE at 170h can be enabled or disabled
    cmp     bx, DEVICE_ATA_DEFAULT_PORT
    je      SHORT .ReturnResultInZF

    ; Check if Secondary IDE channel is enabled
    push    ax
    add     dx, BYTE QD6580_CONTROL_REGISTER
    in      al, dx
    sub     dx, BYTE QD6580_CONTROL_REGISTER
    test    al, FLG_QDCONTROL_SECONDARY_DISABLED_in
    pop     ax
    jz      SHORT .CompareBXtoSecondaryIDE
    ret

    ; QD6500 has only one IDE channel that can be at 1F0h or 170h
.DoesIdePortInDXbelongToQD6500:
    test    al, FLG_QDCONFIG_PRIMARY_IDE
    jz      SHORT .CompareBXtoSecondaryIDE
    cmp     bx, DEVICE_ATA_DEFAULT_PORT
    ret

.CompareBXtoSecondaryIDE:
    cmp     bx, DEVICE_ATA_DEFAULT_SECONDARY_PORT
.ReturnResultInZF:
    ret


;--------------------------------------------------------------------
; Vision_GetMaxPioModeToAL
;   Parameters:
;       AL:     QD65xx Config Register contents
;       AH:     QDI Vision Controller ID (bits 4...7)
;   Returns:
;       AL:     Max supported PIO mode
;       AH:     FLGH_DPT_IORDY if IORDY supported, zero otherwise
;       CF:     Set if PIO limit necessary
;               Cleared if no need to limit timings
;   Corrupts registers:
;       (AX if CF cleared)
;   Corrupts registers:
;       Nothing
;--------------------------------------------------------------------
Vision_GetMaxPioModeToAL:
    cmp     ah, ID_QD6500 << 4
    clc
    jne     SHORT .NoNeedToLimitForQD6580

    mov     ax, 2   ; Limit to PIO 2 because QD6500 does not support IORDY
    stc
.NoNeedToLimitForQD6580:
    ret


;--------------------------------------------------------------------
; Vision_InitializeWithIDinAHandConfigInAL
;   Parameters:
;       AL:     QD65xx Config Register contents
;       AH:     QDI Vision Controller ID (bits 4...7)
;       DS:DI:  Ptr to DPT for Single or Slave Drive
;       SI:     Offset to Master DPT if Slave Drive present
;               Zero if Slave Drive not present
;   Returns:
;       CF:     Cleared if success
;               Set if error
;   Corrupts registers:
;       AX, BX, CX, DX, BP
;--------------------------------------------------------------------
Vision_InitializeWithIDinAHandConfigInAL:
    ; QD6580 has a Control Register that needs to be programmed
    mov     dx, [di+DPT_ADVANCED_ATA.wControllerBasePort]
    cmp     ah, ID_QD6500 << 4
    je      SHORT .CalculateTimingForQD6500

    ; Program QD6580 Control Register (not available on QD6500) to
    ; Enable or Disable Read-Ahead and Post-Write Buffer to match
    ; jumper setting on the multi I/O card.
    xor     ax, ax
    add     dx, BYTE QD6580_CONTROL_REGISTER
    in      al, dx                                  ; Read to get ATAPI jumper status
    test    al, FLG_QDCONTROL_HDONLY_in
    eCMOVNZ ah, FLG_QDCONTROL_NONATAPI              ; Enable Read-Ahead and Post-Write Buffers
    or      ah, MASK_QDCONTROL_FLAGS_TO_SET
    mov     al, ah
    out     dx, al
    sub     dx, BYTE QD6580_CONTROL_REGISTER

    ; Now we need to determine is the drive connected to the Primary or Secondary channel.
    ; QD6500 has only one channel that can be Primary at 1F0h or Secondary at 170h.
    ; QD6580 always has Primary channel at 1F0h. Secondary channel at 170h can be Enabled or Disabled.
    call    AccessDPT_GetIdeBasePortToBX
    cmp     bx, DEVICE_ATA_DEFAULT_PORT
    je      SHORT .CalculateTimingTicksForQD6580    ; Primary Channel so no need to modify DX
    times 2 inc dx                                  ; Secondary Channel IDE Timing Register

    ; QD6500 and QD6580 require slightly different calculations.
.CalculateTimingTicksForQD6580:
    mov     bp, QD6580_MAX_ACTIVE_TIME_CLOCKS | (QD6580_MIN_ACTIVE_TIME_CLOCKS << 8)
    jmp     SHORT .CalculateTimingsForQD65xx

.CalculateTimingForQD6500:
    mov     bp, QD6500_MAX_ACTIVE_TIME_CLOCKS | (QD6500_MIN_ACTIVE_TIME_CLOCKS << 8)

    ; We need the PIO Cycle Time in CX to calculate Active and Recovery Times.
.CalculateTimingsForQD65xx:
    call    AdvAtaInit_SelectSlowestCommonPioTimingsToBXandCXfromDSSIandDSDI

    ; Calculate Active Time value for QD65xx IDE Timing Register
    call    AtaID_GetActiveTimeToAXfromPioModeInBX
    call    ConvertNanosecsFromAXwithLimitsInBPtoRegisterValue
    xchg    bp, ax

    ; Calculate Recovery Time value for QD65xx IDE Timing Register
    call    AtaID_GetRecoveryTimeToAXfromPioModeInBXandCycleTimeInCX
    mov     bx, bp                      ; Active Time value now in BL
    mov     bp, QD65xx_MAX_RECOVERY_TIME_CLOCKS | (QD65xx_MIN_RECOVERY_TIME_CLOCKS << 8)
    call    ConvertNanosecsFromAXwithLimitsInBPtoRegisterValue

    ; Merge the values to a single byte to output
    eSHIFT_IM   al, POSITON_QD65XXIDE_RECOVERY_TIME, shl
    or      al, bl
    out     dx, al
    ret                                 ; Return with CF cleared


;--------------------------------------------------------------------
; ConvertNanosecsFromAXwithLimitsInBPtoRegisterValue
;   Parameters:
;       AX:     Nanosecs to convert
;       BP:     Low Byte:   Maximum allowed ticks
;               High Byte:  Minimum allowed ticks
;       DS:DI:  Ptr to DPT for Single or Slave Drive
;   Returns:
;       AL:     Timing value for QD65xx register
;   Corrupts registers:
;       Nothing
;--------------------------------------------------------------------
ConvertNanosecsFromAXwithLimitsInBPtoRegisterValue:
    push    cx

    ; Get VLB Cycle Time in nanosecs
    mov     cl, VLB_33MHZ_CYCLE_TIME    ; Assume 33 MHz or slower VLB bus
    test    BYTE [di+DPT_ADVANCED_ATA.wControllerID], FLG_QDCONFIG_ID3
    eCMOVZ  cl, VLB_40MHZ_CYCLE_TIME

    ; Convert value in AX to VLB ticks
    div     cl                          ; AL = VLB ticks
    inc     ax                          ; Round up

    ; Limit value to QD65xx limits
    mov     cx, bp
    MAX_U   al, ch                      ; Make sure not below minimum
    MIN_U   al, cl                      ; Make sure not above maximum

    ; Not done yet, we need to invert the ticks since 0 is the slowest
    ; value on the timing register
    sub     cl, al
    xchg    ax, cx                      ; Return in AL

    pop     cx
    ret