source: xtideuniversalbios/trunk/XTIDE_Universal_BIOS/Src/Device/Serial/SerialCommand.asm @ 480

Last change on this file since 480 was 480, checked in by aitotat@…, 11 years ago

Changes to XTIDE Universal BIOS:

  • XT-CF DMA transfers should now work.
File size: 7.8 KB
Line 
1; Project name  :   XTIDE Universal BIOS
2; Description   :   Serial Device Command functions.
3
4;
5; XTIDE Universal BIOS and Associated Tools 
6; Copyright (C) 2009-2010 by Tomi Tilli, 2011-2012 by XTIDE Universal BIOS Team.
7;
8; This program is free software; you can redistribute it and/or modify
9; it under the terms of the GNU General Public License as published by
10; the Free Software Foundation; either version 2 of the License, or
11; (at your option) any later version.
12; 
13; This program is distributed in the hope that it will be useful,
14; but WITHOUT ANY WARRANTY; without even the implied warranty of
15; MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
16; GNU General Public License for more details.     
17; Visit http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
18;       
19
20; Section containing code
21SECTION .text
22
23%define SERIALSERVER_AH_ALREADY_HAS_COMMAND_BYTE
24%define SERIALSERVER_NO_ZERO_SECTOR_COUNTS     
25
26;--------------------------------------------------------------------
27; SerialCommand_OutputWithParameters
28;   Parameters:
29;       BH:     Non-zero if 48-bit addressing used
30;               (ignored at present as 48-bit addressing is not supported)
31;       BL:     IDE Status Register bit to poll after command
32;               (ignored at present, since there is no IDE status register to poll)
33;       ES:SI:  Ptr to buffer (for data transfer commands)
34;       DS:DI:  Ptr to DPT (in RAMVARS segment)
35;       SS:BP:  Ptr to IDEREGS_AND_INTPACK
36;   Returns:
37;       AH:     INT 13h Error Code
38;       CX:     Number of successfully transferred sectors (for transfer commands)
39;       CF:     Cleared if success, Set if error
40;   Corrupts registers:
41;       AL, BX, CX, DX, (ES:SI for data transfer commands)
42;--------------------------------------------------------------------
43ALIGN JUMP_ALIGN
44SerialCommand_OutputWithParameters:
45
46        mov     ah,SerialServer_Command_Read
47
48        mov     al,[bp+IDEPACK.bCommand]
49
50        cmp     al,20h          ; Read Sectors IDE command
51        jz      .readOrWrite
52        inc     ah              ; now SerialServer_Protocol_Write
53        cmp     al,30h          ; Write Sectors IDE command
54        jz      .readOrWrite
55
56;  all other commands return success
57;  including function 0ech which should return drive information, this is handled with the identify functions
58;
59        xor     ah,ah           ;  also clears carry
60        ret
61
62.readOrWrite:
63        call    IdeTransfer_NormalizePointerInESSI
64        mov     [bp+IDEPACK.bFeatures],ah       ; store protocol command
65               
66        mov     dx, [di+DPT_SERIAL.wSerialPortAndBaud]
67
68ALIGN JUMP_ALIGN
69SerialCommand_FallThroughToSerialServer_SendReceive:
70
71%include "SerialServer.asm"
72
73%ifndef CHECK_FOR_UNUSED_ENTRYPOINTS       
74    %if SerialCommand_FallThroughToSerialServer_SendReceive <> SerialServer_SendReceive
75        %error "SerialServer_SendReceive must be the first routine at the top of SerialServer.asm in the Assembly_Library"
76    %endif
77%endif
78
79ALIGN JUMP_ALIGN       
80SerialCommand_ReturnError:     
81        stc
82        ret     
83
84;--------------------------------------------------------------------
85; SerialCommand_IdentifyDeviceToBufferInESSIwithDriveSelectByteInBH
86;   Parameters:
87;       BH:     Drive Select byte for Drive and Head Select Register
88;       DS:     Segment to RAMVARS
89;       ES:SI:  Ptr to buffer to receive 512-byte IDE Information
90;       CS:BP:  Ptr to IDEVARS
91;   Returns:
92;       CF:     Cleared if success, Set if error
93;   Corrupts registers:
94;       AL, BL, CX, DX, SI, DI, ES
95;--------------------------------------------------------------------
96ALIGN JUMP_ALIGN
97SerialCommand_IdentifyDeviceToBufferInESSIwithDriveSelectByteInBH:
98;
99; To improve boot time, we do our best to avoid looking for slave serial drives when we already know the results
100; from the looking for a master.  This is particularly true when doing a COM port scan, as we will end up running
101; through all the COM ports and baud rates a second time.
102;
103; But drive detection isn't the only case - we also need to get the right drive when called on int13h/25h.
104;
105; The decision tree:
106;
107;    Master:
108;          wSerialPortAndBaud Non-Zero:           -> Continue with wSerialPortAndBaud (1)
109;          wSerialPortAndBaud Zero:
110;              previous serial drive not found:   -> Scan (2)
111;              previous serial drive found:       -> Continue with previous serial drive info (3)
112;
113;    Slave:
114;          wSerialPortAndBaud Non-Zero:
115;              previous serial drive not found:   -> Error - Not Found (4)
116;              previous serial drive found:       -> Continue with wSerialPackedAndBaud (5)
117;          wSerialPortAndBaud Zero:
118;              previous serial drive not found:   -> Error - Not Found (4)
119;              previous serial drive found:       -> Continue with previous serial drive info (6)
120;
121; (1) This was a port/baud that was explicitly set with the configurator.  In the drive detection case, as this
122;     is the Master, we are checking out a new controller, and so don't care if we already have a serial drive.
123;     And as with the int13h/25h case, we just go off and get the needed information using the user's setting.
124; (2) We are using the special .ideVarsSerialAuto structure.  During drive detection, we would only be here
125;     if we hadn't already seen a serial drive (since we only scan if no explicit drives are set),
126;     so we go off to scan.
127; (3) We are using the special .ideVarsSerialAuto structure.  We won't get here during drive detection, but
128;     we might get here on an int13h/25h call.  If we have scanned COM drives, they are the ONLY serial drives
129;     in use, and so we use the values from the previously seen serial drive DPT.
130; (4) No master has been found yet, therefore no slave should be found.  Avoiding the slave reduces boot time,
131;     especially in the full COM port scan case.  Note that this is different from the hardware IDE, where we
132;     will scan for a slave even if a master is not present.  Note that if ANY master had been previously found,
133;     we will do the slave scan, which isn't harmful, it just wastes time.  But the most common case (by a wide
134;     margin) will be just one serial controller.
135; (5) A COM port scan for a master had been previously completed, and a drive was found.  In a multiple serial
136;     controller scenario being called with int13h/25h, we need to use the value in bSerialPackedPortAndBaud
137;     to make sure we get the proper drive.
138; (6) A COM port scan for a master had been previously completed, and a drive was found.  We would only get here
139;     if no serial drive was explicitly set by the user in the configurator or that drive had not been found.
140;     Instead of performing the full COM port scan for the slave, use the port/baud value stored during the
141;     master scan.
142;
143        mov     dx,[cs:bp+IDEVARS.wSerialPortAndBaud]
144        xor     ax,ax
145       
146        push    si
147        call    FindDPT_ToDSDIforSerialDevice
148        pop     si
149%ifdef MODULE_SERIAL_FLOPPY
150        jnc     .founddpt
151;
152; If not found above with FindDPT_ToDSDIforSerialDevice, DI will point to the DPT after the last hard disk DPT
153; So, if there was a previously found floppy disk, DI will point to that DPT and we use that value for the slave.
154;
155        cmp     byte [RAMVARS.xlateVars+XLATEVARS.bFlopCntAndFirst], 0
156        jz      .notfounddpt
157.founddpt:
158%else
159        jc      .notfounddpt
160%endif
161        mov     ax, [di+DPT_SERIAL.wSerialPortAndBaud]
162.notfounddpt:
163
164        test    bh, FLG_DRVNHEAD_DRV
165        jz      .master
166
167        test    ax,ax           ; Take care of the case that is different between master and slave.
168        jz      SerialCommand_ReturnError
169
170; fall-through
171.master:
172        test    dx,dx
173        jnz     .identifyDeviceInDX
174
175        xchg    dx, ax          ;  move ax to dx (move previously found serial drive to dx, could be zero)
176
177.identifyDeviceInDX:
178
179ALIGN JUMP_ALIGN
180SerialCommand_FallThroughToSerialServerScan_ScanForServer:     
181       
182%include "SerialServerScan.asm"
183
184%ifndef CHECK_FOR_UNUSED_ENTRYPOINTS               
185    %if SerialCommand_FallThroughToSerialServerScan_ScanForServer <> SerialServerScan_ScanForServer
186        %error "SerialServerScan_ScanForServer must be the first routine at the top of SerialServerScan.asm in the Assembly_Library"
187    %endif
188%endif
189
190
Note: See TracBrowser for help on using the repository browser.