source: xtideuniversalbios/trunk/XTIDE_Universal_BIOS/Src/Device/Serial/SerialCommand.asm@ 273

; Project name  :   XTIDE Universal BIOS
; Description   :   Serial Device Command functions.

; Section containing code
SECTION .text

;--------------- UART Equates -----------------------------
;
; Serial Programming References:
;    http://en.wikibooks.org/wiki/Serial_Programming
;

SerialCommand_UART_base                         EQU     0
SerialCommand_UART_transmitByte                 EQU     0
SerialCommand_UART_receiveByte                  EQU     0

;
; Values for UART_divisorLow:
; 60h = 1200, 30h = 2400, 18h = 4800, 0ch = 9600, 6 = 19200, 4 = 28800, 3 = 38400, 2 = 57600, 1 = 115200
;
SerialCommand_UART_divisorLow                   EQU     0

;
; UART_divisorHigh is zero for all speeds including and above 1200 baud (which is all we do)
;
SerialCommand_UART_divisorHigh                  EQU     1

SerialCommand_UART_interruptIdent               EQU     2
SerialCommand_UART_FIFOControl                  EQU     2

SerialCommand_UART_lineControl                  EQU     3

SerialCommand_UART_modemControl                 EQU     4

SerialCommand_UART_lineStatus                   EQU     5

SerialCommand_UART_modemStatus                  EQU     6

SerialCommand_UART_scratch                      EQU     7

SerialCommand_Protocol_Write                    EQU     3
SerialCommand_Protocol_Read                     EQU     2
SerialCommand_Protocol_Inquire                  EQU     0
SerialCommand_Protocol_Header                   EQU     0a0h

;--------------------------------------------------------------------
; SerialCommand_OutputWithParameters
;   Parameters:
;       BH:     Non-zero if 48-bit addressing used
;               (ignored at present as 48-bit addressing is not supported)
;       BL:     IDE Status Register bit to poll after command
;               (ignored at present, since there is no IDE status register to poll)
;       ES:SI:  Ptr to buffer (for data transfer commands)
;       DS:DI:  Ptr to DPT (in RAMVARS segment)
;       SS:BP:  Ptr to IDEREGS_AND_INTPACK
;   Returns:
;       AH:     INT 13h Error Code
;       CX:     Number of successfully transferred sectors (for transfer commands)
;       CF:     Cleared if success, Set if error
;   Corrupts registers:
;       AL, BX, CX, DX, (ES:SI for data transfer commands)
;--------------------------------------------------------------------
ALIGN JUMP_ALIGN
SerialCommand_OutputWithParameters:

        mov     ah,(SerialCommand_Protocol_Header | SerialCommand_Protocol_Read)

        mov     al,[bp+IDEPACK.bCommand]

        cmp     al,20h          ; Read Sectors IDE command
        jz      .readOrWrite
        inc     ah              ; now SerialCommand_Protocol_Write
        cmp     al,30h          ; Write Sectors IDE command
        jz      .readOrWrite

;  all other commands return success
;  including function 0ech which should return drive information, this is handled with the identify functions
;
        xor     ah,ah           ;  also clears carry
        ret

.readOrWrite:
        mov     [bp+IDEPACK.bFeatures],ah       ; store protocol command

        mov     dx, [di+DPT_SERIAL.wSerialPortAndBaud]

; fall-through

;--------------------------------------------------------------------
; SerialCommand_OutputWithParameters_DeviceInDX
;   Parameters:
;       AH:     Protocol Command
;       DX:     Packed I/O port and baud rate
;       ES:SI:  Ptr to buffer (for data transfer commands)
;       SS:BP:  Ptr to IDEREGS_AND_INTPACK
;   Returns:
;       AH:     INT 13h Error Code
;       CF:     Cleared if success, Set if error
;   Corrupts registers:
;       AL, BX, CX, DX, (ES:SI for data transfer commands)
;--------------------------------------------------------------------
SerialCommand_OutputWithParameters_DeviceInDX:

        push    si
        push    di
        push    bp

;
; Unpack I/O port and baud from DPT
;       Port to DX for the remainder of the routine (+/- different register offsets)
;       Baud in CH until UART initialization is complete
;
        mov     ch,dh
        xor     dh,dh
        eSHL_IM dx, 2           ; shift from one byte to two

        mov     al,[bp+IDEPACK.bSectorCount]

;
; Command byte and sector count live at the top of the stack, pop/push are used to access
;
        push    ax

%if 0
        cld     ; Shouldn't be needed. DF has already been cleared (line 24, Int13h.asm)
%endif

;----------------------------------------------------------------------
;
; Initialize UART
;
; We do this each time since DOS (at boot) or another program may have
; decided to reprogram the UART
;
        mov     bl,dl           ; setup BL with proper values for read/write loops (BH comes later)

        mov     al,83h
        add     dl,SerialCommand_UART_lineControl
        out     dx,al

        mov     al,ch
        mov     dl,bl           ; divisor low
        out     dx,al

        xor     ax,ax
        inc     dx              ; divisor high
        push    dx
        out     dx,al

        mov     al,047h
        inc     dx              ;  fifo
        out     dx,al

        mov     al,03h
        inc     dx              ;  linecontrol
        out     dx,al

        mov     al,0bh
        inc     dx              ;  modemcontrol
        out     dx,al

        inc     dx              ;  linestatus (no output now, just setting up BH for later use)
        mov     bh,dl

        pop     dx              ; base, interrupts disabled
        xor     ax,ax
        out     dx,al

;----------------------------------------------------------------------
;
; Send Command
;
; Sends first six bytes of IDEREGS_AND_INTPACK as the command
;
        push    es              ; save off real buffer location
        push    si

        mov     si,bp           ; point to IDEREGS for command dispatch;
        push    ss
        pop     es

        mov     di,0ffffh       ; initialize checksum for write
        mov     bp,di

        mov     cx,4            ; writing 3 words (plus 1)

        cli                     ; interrupts off...

        call    SerialCommand_WriteProtocol.entry

        pop     di              ; restore real buffer location (note change from SI to DI)
                                ; Buffer is primarily referenced through ES:DI throughout, since
                                ; we need to store (read sector) faster than we read (write sector)
        pop     es

%if 0
;;; no longer needed, since the pointer is normalized before we are called and we do not support
;;; more than 128 sectors (and for 128 specifically, the pointer must be segment aligned).
;;; See comments below at the point this entry point was called for more details...
.nextSectorNormalize:
        call    Registers_NormalizeESDI
%endif

        pop     ax              ; load command byte (done before call to .nextSector on subsequent iterations)
        push    ax

;
; Top of the read/write loop, one iteration per sector
;
.nextSector:
        mov     si,0ffffh       ; initialize checksum for read or write
        mov     bp,si

        mov     cx,0101h        ; writing 256 words (plus 1)

        shr     ah,1            ; command byte, are we doing a write?
        jnc     .readEntry

        xchg    si,di
        call    SerialCommand_WriteProtocol.entry
        xchg    si,di

        inc     cx              ; CX = 1 now (0 out of WriteProtocol)
        jmp     .readEntry

;----------------------------------------------------------------------
;
; Timeout
;
; To save code space, we use the contents of DL to decide which byte in the word to return for reading.
;
.readTimeout:
        push    ax              ; not only does this push preserve AX (which we need), but it also
                                ; means the stack has the same number of bytes on it as when we are
                                ; sending a packet, important for error cleanup and exit
        mov     ah,1
        call    SerialCommand_WaitAndPoll_Read
        pop     ax
        test    dl,1
        jz      .readByte1Ready
        jmp     .readByte2Ready

;----------------------------------------------------------------------------
;
; Read Block (without interrupts, used when there is a FIFO, high speed)
;
; NOTE: This loop is very time sensitive.  Literally, another instruction
; cannot be inserted into this loop without us falling behind at high
; speed (460.8K baud) on a 4.77Mhz 8088, making it hard to receive
; a full 512 byte block.
;
.readLoop:
        stosw                   ; store word in caller's data buffer

        add     bp, ax          ; update Fletcher's checksum
        adc     bp, 0
        add     si, bp
        adc     si, 0

.readEntry:
        mov     dl,bh
        in      al,dx
        shr     al,1            ; data ready (byte 1)?
        mov     dl,bl           ; get ready to read data
        jnc     .readTimeout    ; nope not ready, update timeouts

;
; Entry point after initial timeout.  We enter here so that the checksum word
; is not stored (and is left in AX after the loop is complete).
;
.readByte1Ready:
        in      al, dx          ; read data byte 1

        mov     ah, al          ; store byte in ah for now

;
; note the placement of this reset of dl to bh, and that it is
; before the return, which is assymetric with where this is done
; above for byte 1.  The value of dl is used by the timeout routine
; to know which byte to return to (.read_byte1_ready or
; .read_byte2_ready)
;
        mov     dl,bh

        in      al,dx
        shr     al,1            ; data ready (byte 2)?
        jnc     .readTimeout
.readByte2Ready:
        mov     dl,bl
        in      al, dx          ; read data byte 2

        xchg    al, ah          ; ah was holding byte 1, reverse byte order

        loop    .readLoop

        sti                     ; interrupts back on ASAP, between packets

;
; Compare checksums
;
        xchg    ax,bp
        xor     ah,al
        mov     cx,si
        xor     cl,ch
        mov     al,cl
        cmp     ax,bp
        jnz     SerialCommand_OutputWithParameters_Error

        pop     ax              ; sector count and command byte
        dec     al              ; decrement sector count
        push    ax              ; save
        jz      SerialCommand_OutputWithParameters_ReturnCodeInAL

        cli                     ; interrupts back off for ACK byte to host
                                ; (host could start sending data immediately)
        out     dx,al           ; ACK with next sector number

%if 0
;;; This code is no longer needed as we do not support more than 128 sectors, and for 128 the pointer
;;; must be segment aligned.  If we ever do want to support more sectors, the code can help...

;
; Normalize buffer pointer for next go round, if needed.
;
; We need to re-normalize the pointer in ES:DI after processing every 7f sectors.  That number could
; have been 80 if we knew the offset was on a segment boundary, but this may not be the case.
;
; We re-normalize based on the sector count (flags from "dec al" above)...
;    a) we normalize before the first sector goes out, immediately after sending the command packet (above)
;    b) on transitions from FF to FE, very rare case for writing 255 or 256 sectors
;    c) on transitions from 80 to 7F, a large read/write
;    d) on transitions from 00 to FF, very, very rare case of writing 256 sectors
;       We don't need to renormalize in this case, but it isn't worth the memory/effort to not do
;       the extra work, and it does no harm.
;
; I really don't care much about (d) because I have not seen cases where any OS makes a request
; for more than 127 sectors.  Back in the day, it appears that some BIOS could not support more than 127
; sectors, so that may be the practical limit for OS and application developers.  The Extended BIOS
; function also appear to be capped at 127 sectors.  So although this can support the full 256 sectors
; if needed, we are optimized for that 1-127 range.
;
; Assume we start with 0000:000f, with 256 sectors to write...
;    After first packet, 0000:020f
;    First decrement of AL, transition from 00 to FF: renormalize to 0020:000f (unnecessary)
;    After second packet, 0020:020f
;    Second derement of AL, transition from FF to FE: renormalize to 0040:000f
;    After 7f more packets, 0040:fe0f
;    Decrement of AL, transition from 80 to 7F: renormalize to 1020:000f
;    After 7f more packets, 1020:fe0f or 2000:000f if normalized
;    Decrement of AL, from 1 to 0: exit
;
        jge     short .nextSector       ; OF=SF, branch for 1-7e, most common case
                                        ; (0 kicked out above for return success)

        add     al,2                    ; 7f-ff moves to 81-01
                                        ; (0-7e kicked out before we get here)
                                        ; 7f moves to 81 and OF=1, so OF=SF
                                        ; fe moves to 0 and OF=0, SF=0, so OF=SF
                                        ; ff moves to 1 and OF=0, SF=0, so OF=SF
                                        ; 80-fd moves to 82-ff and OF=0, so OF<>SF

        jl      short .nextSector       ; OF<>SF, branch for all cases but 7f, fe, and ff

;       jpo     short .nextSector       ; if we really wanted to avoid normalizing for ff, this
                                        ; is one way to do it, but it adds more memory and more
                                        ; cycles for the 7f and fe cases.  IMHO, given that I've
                                        ; never seen a request for more than 7f, this seems unnecessary.

        jmp     short .nextSectorNormalize  ; our two renormalization cases (plus one for ff)

%else

        jmp     short .nextSector

%endif

;---------------------------------------------------------------------------
;
; Cleanup, error reporting, and exit
;

;
; Used in situations where a call is underway, such as with SerialCommand_WaitAndPoll
;
ALIGN JUMP_ALIGN
SerialCommand_OutputWithParameters_ErrorAndPop4Words:
        add     sp,8
;;; fall-through

ALIGN JUMP_ALIGN
SerialCommand_OutputWithParameters_Error:
;----------------------------------------------------------------------
;
; Clear read buffer
;
; In case there are extra characters or an error in the FIFO, clear it out.
; In theory the initialization of the UART registers above should have
; taken care of this, but I have seen cases where this is not true.
;
        xor     cx,cx                   ; timeout this clearing routine, in case the UART isn't there
.clearBuffer:
        mov     dl,bh
        in      al,dx
        mov     dl,bl
        test    al,08fh
        jz      .clearBufferComplete
        test    al,1
        in      al,dx
        loopnz  .clearBuffer            ; note ZF from test above

.clearBufferComplete:
        mov     al, 3           ;  error return code and CF (low order bit)

ALIGN JUMP_ALIGN
SerialCommand_OutputWithParameters_ReturnCodeInAL:
%if 0
        sti                     ;  all paths here will already have interrupts turned back on
%endif
        mov     ah, al          ;  for success, AL will already be zero

        pop     bx              ;  recover "ax" (command and count) from stack

        pop     bp
        pop     di
        pop     si

        mov     ch, 0
        mov     cl,[bp+IDEPACK.bSectorCount]
        sub     cl, bl          ; subtract off the number of sectors that remained
        
        shr     ah, 1           ; shift down return code and CF

        ret

;--------------------------------------------------------------------
; SerialCommand_WriteProtocol
;
; NOTE: As with its read counterpart, this loop is very time sensitive.
; Although it will still function, adding additional instructions will
; impact the write throughput, especially on slower machines.
;
;   Parameters:
;       ES:SI:  Ptr to buffer
;       CX:     Words to write, plus 1
;       BP/DI:  Initialized for Checksum (-1 in each)
;       DH:     I/O Port high byte
;       BX:     LineStatus Register address (BH) and Receive/Transmit Register address (BL)
;   Returns:
;       BP/DI:  Checksum for written bytes, compared against ACK from server in .readLoop
;       CX:     Zero
;       DL:     Receive/Transmit Register address
;   Corrupts registers:
;       AX
;--------------------------------------------------------------------
ALIGN JUMP_ALIGN
SerialCommand_WriteProtocol:
.writeLoop:
        es lodsw                ; fetch next word

        out     dx,al           ; output first byte

        add     bp,ax           ; update checksum
        adc     bp,0
        add     di,bp
        adc     di,0

        mov     dl,bh           ; transmit buffer empty?
        in      al,dx
        test    al,20h
        jz      .writeTimeout2  ; nope, use our polling routine

.writeByte2Ready:
        mov     dl,bl
        mov     al,ah           ; output second byte
        out     dx,al

.entry:
        mov     dl,bh           ; transmit buffer empty?
        in      al,dx
        test    al,20h
        mov     dl,bl
        jz      .writeTimeout1  ; nope, use our polling routine

.writeByte1Ready:
        loop    .writeLoop

        mov     ax,di           ; fold Fletcher's checksum and output
        xor     al,ah
        out     dx,al           ; byte 1

        call    SerialCommand_WaitAndPoll_Write

        mov     ax,bp
        xor     al,ah
        out     dx,al           ; byte 2

        ret

.writeTimeout2:
        mov     dl,ah           ; need to preserve AH, but don't need DL (will be reset upon return)
        call    SerialCommand_WaitAndPoll_Write
        mov     ah,dl
        jmp     .writeByte2Ready

.writeTimeout1:
%ifndef USE_186
        mov     ax,.writeByte1Ready
        push    ax              ; return address for ret at end of SC_writeTimeout2
%else
        push    .writeByte1Ready
%endif
;;; fall-through

;--------------------------------------------------------------------
; SerialCommand_WaitAndPoll
;
;   Parameters:
;       AH:     UART_LineStatus bit to test (20h for write, or 1h for read)
;               One entry point fills in AH with 20h for write
;       DX:     Port address (OK if already incremented to UART_lineStatus)
;       BX:
;       Stack:  2 words on the stack below the command/count word
;   Returns:
;       Returns when desired UART_LineStatus bit is cleared
;       Jumps directly to error exit if timeout elapses (and cleans up stack)
;   Corrupts registers:
;       AX
;--------------------------------------------------------------------

SerialCommand_WaitAndPoll_SoftDelayTicks   EQU   20

ALIGN JUMP_ALIGN
SerialCommand_WaitAndPoll_Write:
        mov     ah,20h
;;; fall-through

ALIGN JUMP_ALIGN
SerialCommand_WaitAndPoll_Read:
        push    cx
        push    dx

;
; We first poll in a tight loop, interrupts off, for the next character to come in/be sent
;
        xor     cx,cx
.readTimeoutLoop:
        mov     dl,bh
        in      al,dx
        test    al,ah
        jnz     .readTimeoutComplete
        loop    .readTimeoutLoop

;
; If that loop completes, then we assume there is a long delay involved, turn interrupts back on
; and wait for a given number of timer ticks to pass.
;
        sti
        mov     cl,SerialCommand_WaitAndPoll_SoftDelayTicks
        call    Timer_InitializeTimeoutWithTicksInCL
.WaitAndPoll:
        call    Timer_SetCFifTimeout
        jc      SerialCommand_OutputWithParameters_ErrorAndPop4Words
        in      al,dx
        test    al,ah
        jz      .WaitAndPoll
        cli

.readTimeoutComplete:
        pop     dx
        pop     cx
        ret

;--------------------------------------------------------------------
; SerialCommand_IdentifyDeviceToBufferInESSIwithDriveSelectByteInBH
;   Parameters:
;       BH:     Drive Select byte for Drive and Head Select Register
;       DS:     Segment to RAMVARS
;       ES:SI:  Ptr to buffer to receive 512-byte IDE Information
;       CS:BP:  Ptr to IDEVARS
;   Returns:
;       AH:     INT 13h Error Code
;               NOTE: Not set (or checked) during drive detection
;       CF:     Cleared if success, Set if error
;   Corrupts registers:
;       AL, BL, CX, DX, SI, DI, ES
;--------------------------------------------------------------------
ALIGN JUMP_ALIGN
SerialCommand_IdentifyDeviceToBufferInESSIwithDriveSelectByteInBH:
;
; To improve boot time, we do our best to avoid looking for slave serial drives when we already know the results
; from the looking for a master.  This is particularly true when doing a COM port scan, as we will end up running
; through all the COM ports and baud rates a second time.
;
; But drive detection isn't the only case - we also need to get the right drive when called on int13h/25h.
;
; The decision tree:
;
;    Master:
;          wSerialPortAndBaud Non-Zero:           -> Continue with wSerialPortAndBaud (1)
;          wSerialPortAndBaud Zero:
;              previous serial drive not found:   -> Scan (2)
;              previous serial drive found:       -> Continue with previous serial drive info (3)
;
;    Slave:
;          wSerialPortAndBaud Non-Zero:
;              previous serial drive not found:   -> Error - Not Found (4)
;              previous serial drive found:       -> Continue with wSerialPackedAndBaud (5)
;          wSerialPortAndBaud Zero:
;              previous serial drive not found:   -> Error - Not Found (4)
;              previous serial drive found:       -> Continue with previous serial drive info (6)
;
; (1) This was a port/baud that was explicitly set with the configurator.  In the drive detection case, as this
;     is the Master, we are checking out a new controller, and so don't care if we already have a serial drive.
;     And as with the int13h/25h case, we just go off and get the needed information using the user's setting.
; (2) We are using the special .ideVarsSerialAuto structure.  During drive detection, we would only be here
;     if we hadn't already seen a serial drive (since we only scan if no explicit drives are set),
;     so we go off to scan.
; (3) We are using the special .ideVarsSerialAuto structure.  We won't get here during drive detection, but
;     we might get here on an int13h/25h call.  If we have scanned COM drives, they are the ONLY serial drives
;     in use, and so we use the values from the previously seen serial drive DPT.
; (4) No master has been found yet, therefore no slave should be found.  Avoiding the slave reduces boot time,
;     especially in the full COM port scan case.  Note that this is different from the hardware IDE, where we
;     will scan for a slave even if a master is not present.  Note that if ANY master had been previously found,
;     we will do the slave scan, which isn't harmful, it just wastes time.  But the most common case (by a wide
;     margin) will be just one serial controller.
; (5) A COM port scan for a master had been previously completed, and a drive was found.  In a multiple serial
;     controller scenario being called with int13h/25h, we need to use the value in bSerialPackedPortAndBaud
;     to make sure we get the proper drive.
; (6) A COM port scan for a master had been previously completed, and a drive was found.  We would only get here
;     if no serial drive was explicitly set by the user in the configurator or that drive had not been found.
;     Instead of performing the full COM port scan for the slave, use the port/baud value stored during the
;     master scan.
;
        mov     cx,1            ; 1 sector to move, 0 for non-scan
        mov     dx,[cs:bp+IDEVARS.wSerialPortAndBaud]
        xor     ax,ax
        push    si
        call    FindDPT_ToDSDIforSerialDevice
        pop     si
%ifdef MODULE_SERIAL_FLOPPY
        jnc     .founddpt
;
; If not found above with FindDPT_ToDSDIforSerialDevice, DI will point to the DPT after the last hard disk DPT
;
        cmp     byte [RAMVARS.xlateVars+XLATEVARS.bFlopCntAndFirst], 0
        jz      .notfounddpt
.founddpt:
%else
        jnc     .notfounddpt
%endif
        mov     ax, [di+DPT_SERIAL.wSerialPortAndBaud]
.notfounddpt:

        test    bh, FLG_DRVNHEAD_DRV
        jz      .master

        test    ax,ax           ; Take care of the case that is different between master and slave.
        jz      .error          ; Because we do this here, the jz after the "or" below will not be taken

; fall-through
.master:
        test    dx,dx
        jnz     .identifyDeviceInDX

        or      dx,ax           ; Since DX is zero, this effectively moves the previously found serial drive
                                ; information to dx, as well as test for zero
        jz      .scanSerial

; fall-through
.identifyDeviceInDX:

        push    bp              ; setup fake IDEREGS_AND_INTPACK

        push    dx

        push    cx

        mov     bl,0a0h         ; protocol command to ah and onto stack with bh
        mov     ah,bl

        push    bx

        mov     bp,sp
        call    SerialCommand_OutputWithParameters_DeviceInDX

        pop     bx

        pop     cx
        pop     dx

        pop     bp
;
; place port and baud word in to the return sector, in a vendor specific area,
; which is read by FinalizeDPT and DetectDrives
;
        mov     [es:si+ATA6.wSerialPortAndBaud],dx

.notFound:
        ret

;----------------------------------------------------------------------
;
; SerialCommand_AutoSerial
;
; When the SerialAuto IDEVARS entry is used, scans the COM ports on the machine for a possible serial connection.
;

.scanPortAddresses: db  DEVICE_SERIAL_COM7 >> 2
                    db  DEVICE_SERIAL_COM6 >> 2
                    db  DEVICE_SERIAL_COM5 >> 2
                    db  DEVICE_SERIAL_COM4 >> 2
                    db  DEVICE_SERIAL_COM3 >> 2
                    db  DEVICE_SERIAL_COM2 >> 2
                    db  DEVICE_SERIAL_COM1 >> 2
                    db  0

ALIGN JUMP_ALIGN
.scanSerial:
        mov     di,.scanPortAddresses-1
        mov     ch,1            ;  tell server that we are scanning

.nextPort:
        inc     di              ; load next port address
        xor     dh, dh
        mov     dl,[cs:di]
        eSHL_IM dx, 2           ; shift from one byte to two
        jz      .error

;
; Test for COM port presence, write to and read from registers
;
        push    dx
        add     dl,SerialCommand_UART_lineControl
        mov     al, 09ah
        out     dx, al
        in      al, dx
        pop     dx
        cmp     al, 09ah
        jnz     .nextPort

        mov     al, 0ch
        out     dx, al
        in      al, dx
        cmp     al, 0ch
        jnz     .nextPort

;
; Begin baud rate scan on this port...
;
; On a scan, we support 6 baud rates, starting here and going higher by a factor of two each step, with a
; small jump between 9600 and 38800.  These 6 were selected since we wanted to support 9600 baud and 115200,
; *on the server side* if the client side had a 4x clock multiplier, a 2x clock multiplier, or no clock multiplier.
;
; Starting with 30h, that means 30h (2400 baud), 18h (4800 baud), 0ch (9600 baud), and
;                               04h (28800 baud), 02h (57600 baud), 01h (115200 baud)
;
; Note: hardware baud multipliers (2x, 4x) will impact the final baud rate and are not known at this level
;
        mov     dh,030h * 2     ; multiply by 2 since we are about to divide by 2
        mov     dl,[cs:di]      ; restore single byte port address for scan

.nextBaud:
        shr     dh,1
        jz      .nextPort
        cmp     dh,6            ; skip from 6 to 4, to move from the top of the 9600 baud range
        jnz     .testBaud       ; to the bottom of the 115200 baud range
        mov     dh,4

.testBaud:
        call    .identifyDeviceInDX
        jc      .nextBaud

        ret

.error:
        stc
%if 0
        mov     ah,1        ; setting the error code is unnecessary as this path can only be taken during
                            ; drive detection, and drive detection works off CF and does not check AH
%endif
        ret