[150] | 1 | ; Project name : XTIDE Universal BIOS |
---|
| 2 | ; Description : Serial Device Command functions. |
---|
| 3 | |
---|
| 4 | ; Section containing code |
---|
| 5 | SECTION .text |
---|
| 6 | |
---|
[179] | 7 | ;--------------- UART Equates ----------------------------- |
---|
| 8 | ; |
---|
| 9 | ; Serial Programming References: |
---|
| 10 | ; http://en.wikibooks.org/wiki/Serial_Programming |
---|
| 11 | ; |
---|
[181] | 12 | |
---|
[179] | 13 | SerialCommand_UART_base EQU 0 |
---|
| 14 | SerialCommand_UART_transmitByte EQU 0 |
---|
| 15 | SerialCommand_UART_receiveByte EQU 0 |
---|
| 16 | SerialCommand_UART_divisorLow EQU 0 |
---|
[181] | 17 | ; Values for UART_divisorLow: |
---|
[179] | 18 | ; 60h = 1200, 30h = 2400, 18h = 4800, 0ch = 9600, 6 = 19200, 3 = 38400, 2 = 57600, 1 = 115200 |
---|
| 19 | |
---|
| 20 | SerialCommand_UART_divisorLow_startingBaud EQU 030h |
---|
| 21 | ; We support 4 baud rates, starting here going higher and skipping every other baud rate |
---|
| 22 | ; Starting with 30h, that means 30h (1200 baud), 0ch (9600 baud), 3 (38400 baud), and 1 (115200 baud) |
---|
| 23 | ; Note: hardware baud multipliers (2x, 4x) will impact the final baud rate and are not known at this level |
---|
| 24 | |
---|
[181] | 25 | SerialCommand_UART_interruptEnable EQU 1 |
---|
[179] | 26 | SerialCommand_UART_divisorHigh EQU 1 |
---|
| 27 | ; UART_divisorHigh is zero for all speeds including and above 1200 baud |
---|
| 28 | |
---|
| 29 | SerialCommand_UART_interruptIdent EQU 2 |
---|
| 30 | SerialCommand_UART_FIFOControl EQU 2 |
---|
| 31 | |
---|
| 32 | SerialCommand_UART_lineControl EQU 3 |
---|
[181] | 33 | |
---|
[179] | 34 | SerialCommand_UART_modemControl EQU 4 |
---|
| 35 | |
---|
| 36 | SerialCommand_UART_lineStatus EQU 5 |
---|
| 37 | |
---|
| 38 | SerialCommand_UART_modemStatus EQU 6 |
---|
| 39 | |
---|
| 40 | SerialCommand_UART_scratch EQU 7 |
---|
| 41 | |
---|
[196] | 42 | ; note that the actual StaringPoint port address is not achievable (results in 0 which triggers auto detect) |
---|
[181] | 43 | SerialCommand_PackedPortAndBaud_StartingPort EQU 240h |
---|
[196] | 44 | |
---|
[179] | 45 | SerialCommand_PackedPortAndBaud_PortMask EQU 0fch ; upper 6 bits - 240h through 438h |
---|
| 46 | SerialCommand_PackedPortAndBaud_BaudMask EQU 3 ; lower 2 bits - 4 baud rates |
---|
| 47 | |
---|
| 48 | SerialCommand_Protocol_Write EQU 3 |
---|
| 49 | SerialCommand_Protocol_Read EQU 2 |
---|
| 50 | SerialCommand_Protocol_Inquire EQU 0 |
---|
| 51 | SerialCommand_Protocol_Header EQU 0a0h |
---|
[181] | 52 | |
---|
[150] | 53 | ;-------------------------------------------------------------------- |
---|
[179] | 54 | ; SerialCommand_OutputWithParameters |
---|
[150] | 55 | ; Parameters: |
---|
[179] | 56 | ; BH: Non-zero if 48-bit addressing used |
---|
| 57 | ; (ignored at present as 48-bit addressing is not supported) |
---|
| 58 | ; BL: IDE Status Register bit to poll after command |
---|
| 59 | ; (ignored at present, since there is no IDE status register to poll) |
---|
| 60 | ; ES:SI: Ptr to buffer (for data transfer commands) |
---|
| 61 | ; DS:DI: Ptr to DPT (in RAMVARS segment) |
---|
| 62 | ; SS:BP: Ptr to IDEREGS_AND_INTPACK |
---|
[150] | 63 | ; Returns: |
---|
| 64 | ; AH: INT 13h Error Code |
---|
| 65 | ; CF: Cleared if success, Set if error |
---|
| 66 | ; Corrupts registers: |
---|
[179] | 67 | ; AL, BX, CX, DX, (ES:SI for data transfer commands) |
---|
[150] | 68 | ;-------------------------------------------------------------------- |
---|
| 69 | ALIGN JUMP_ALIGN |
---|
[179] | 70 | SerialCommand_OutputWithParameters: |
---|
[181] | 71 | |
---|
[179] | 72 | mov ah,(SerialCommand_Protocol_Header | SerialCommand_Protocol_Read) |
---|
[181] | 73 | |
---|
[179] | 74 | mov al,[bp+IDEPACK.bCommand] |
---|
[150] | 75 | |
---|
[179] | 76 | cmp al,20h ; Read Sectors IDE command |
---|
| 77 | jz .readOrWrite |
---|
| 78 | inc ah ; now SerialCommand_Protocol_Write |
---|
| 79 | cmp al,30h ; Write Sectors IDE command |
---|
| 80 | jz .readOrWrite |
---|
[181] | 81 | |
---|
[179] | 82 | ; all other commands return success |
---|
| 83 | ; including function 0ech which should return drive information, this is handled with the identify functions |
---|
| 84 | xor ah,ah ; also clears carry |
---|
| 85 | ret |
---|
[181] | 86 | |
---|
| 87 | .readOrWrite: |
---|
[179] | 88 | mov [bp+IDEPACK.bFeatures],ah ; store protocol command |
---|
[181] | 89 | |
---|
| 90 | mov dl, byte [di+DPT.bSerialPortAndBaud] |
---|
| 91 | |
---|
[179] | 92 | ; fall-through |
---|
[150] | 93 | |
---|
| 94 | ;-------------------------------------------------------------------- |
---|
[179] | 95 | ; SerialCommand_OutputWithParameters_DeviceInDL |
---|
[150] | 96 | ; Parameters: |
---|
[181] | 97 | ; AH: Protocol Command |
---|
[179] | 98 | ; DL: Packed I/O port and baud rate |
---|
[150] | 99 | ; ES:SI: Ptr to buffer (for data transfer commands) |
---|
| 100 | ; SS:BP: Ptr to IDEREGS_AND_INTPACK |
---|
| 101 | ; Returns: |
---|
| 102 | ; AH: INT 13h Error Code |
---|
| 103 | ; CF: Cleared if success, Set if error |
---|
| 104 | ; Corrupts registers: |
---|
| 105 | ; AL, BX, CX, DX, (ES:SI for data transfer commands) |
---|
[181] | 106 | ;-------------------------------------------------------------------- |
---|
[179] | 107 | SerialCommand_OutputWithParameters_DeviceInDL: |
---|
[181] | 108 | |
---|
[179] | 109 | push si |
---|
| 110 | push di |
---|
| 111 | push bp |
---|
| 112 | push es |
---|
| 113 | |
---|
[181] | 114 | ; |
---|
[179] | 115 | ; Unpack I/O port and baud from DPT |
---|
| 116 | ; Port to DX more or less for the remainder of the routine |
---|
| 117 | ; Baud in CH until UART initialization is complete |
---|
| 118 | ; |
---|
| 119 | mov cl, dl |
---|
[181] | 120 | |
---|
[199] | 121 | and cl, DEVICE_SERIAL_PACKEDPORTANDBAUD_BAUDMASK |
---|
[179] | 122 | shl cl, 1 |
---|
| 123 | mov ch, SerialCommand_UART_divisorLow_startingBaud |
---|
| 124 | shr ch, cl |
---|
| 125 | adc ch, 0 |
---|
| 126 | |
---|
[199] | 127 | and dl, DEVICE_SERIAL_PACKEDPORTANDBAUD_PORTMASK |
---|
[181] | 128 | mov dh, 0 |
---|
[196] | 129 | shl dx, 1 ; port offset already x4, needs one more shift to be x8 |
---|
[199] | 130 | add dx, DEVICE_SERIAL_PACKEDPORTANDBAUD_STARTINGPORT |
---|
[179] | 131 | |
---|
| 132 | ; |
---|
| 133 | ; Buffer is referenced through ES:DI throughout, since we need to store faster than we read |
---|
[181] | 134 | ; |
---|
[179] | 135 | mov di,si |
---|
| 136 | |
---|
| 137 | mov al,[bp+IDEPACK.bSectorCount] |
---|
| 138 | |
---|
| 139 | ; |
---|
| 140 | ; Command byte and sector count live at the top of the stack, pop/push are used to access |
---|
[181] | 141 | ; |
---|
[179] | 142 | push ax |
---|
| 143 | |
---|
[181] | 144 | ; cld ; Shouldn't be needed. DF has already been cleared (line 24, Int13h.asm) |
---|
| 145 | |
---|
[179] | 146 | ;---------------------------------------------------------------------- |
---|
| 147 | ; |
---|
| 148 | ; Initialize UART |
---|
| 149 | ; |
---|
[181] | 150 | ; We do this each time since DOS (at boot) or another program may have |
---|
[179] | 151 | ; decided to reprogram the UART |
---|
| 152 | ; |
---|
| 153 | push dx |
---|
[181] | 154 | |
---|
[179] | 155 | mov al,83h |
---|
| 156 | add dl,SerialCommand_UART_lineControl |
---|
| 157 | out dx,al |
---|
| 158 | |
---|
| 159 | mov al,ch |
---|
| 160 | pop dx ; divisor low |
---|
| 161 | out dx,al |
---|
| 162 | |
---|
| 163 | xor ax,ax |
---|
| 164 | inc dx ; divisor high |
---|
| 165 | push dx |
---|
| 166 | out dx,al |
---|
| 167 | |
---|
| 168 | mov al,047h |
---|
| 169 | inc dx ; fifo |
---|
[181] | 170 | out dx,al |
---|
[179] | 171 | |
---|
| 172 | mov al,03h |
---|
| 173 | inc dx ; linecontrol |
---|
| 174 | out dx,al |
---|
| 175 | |
---|
| 176 | mov al,0bh |
---|
| 177 | inc dx ; modemcontrol |
---|
| 178 | out dx,al |
---|
| 179 | |
---|
| 180 | pop dx ; base, interrupts disabled |
---|
| 181 | xor ax,ax |
---|
| 182 | out dx,al |
---|
| 183 | dec dx |
---|
| 184 | |
---|
| 185 | ;---------------------------------------------------------------------- |
---|
| 186 | ; |
---|
| 187 | ; Send Command |
---|
| 188 | ; |
---|
| 189 | ; Sends first six bytes of IDEREGS_AND_INTPACK as the command |
---|
| 190 | ; |
---|
| 191 | call Registers_NormalizeESDI |
---|
| 192 | |
---|
| 193 | push es ; save off real buffer location |
---|
| 194 | push di |
---|
[181] | 195 | |
---|
| 196 | mov di,bp ; point to IDEREGS for command dispatch; |
---|
[179] | 197 | push ss |
---|
| 198 | pop es |
---|
| 199 | |
---|
| 200 | xor si,si ; initialize checksum for write |
---|
[181] | 201 | dec si |
---|
[179] | 202 | mov bp,si |
---|
| 203 | |
---|
| 204 | mov bl,03h ; writing 3 words |
---|
[181] | 205 | |
---|
[179] | 206 | call SerialCommand_WriteProtocol |
---|
| 207 | |
---|
| 208 | pop di ; restore real buffer location |
---|
| 209 | pop es |
---|
| 210 | |
---|
| 211 | pop ax ; load command byte (done before call to .nextSector on subsequent iterations) |
---|
| 212 | push ax |
---|
| 213 | |
---|
| 214 | ; |
---|
| 215 | ; Top of the read/write loop, one iteration per sector |
---|
[181] | 216 | ; |
---|
[179] | 217 | .nextSector: |
---|
| 218 | xor si,si ; initialize checksum for read or write |
---|
| 219 | dec si |
---|
| 220 | mov bp,si |
---|
| 221 | |
---|
| 222 | mov bx,0100h |
---|
[181] | 223 | |
---|
[179] | 224 | shr ah,1 ; command byte, are we doing a write? |
---|
| 225 | jnc .readSector |
---|
| 226 | call SerialCommand_WriteProtocol |
---|
[181] | 227 | |
---|
[179] | 228 | xor bx,bx |
---|
| 229 | |
---|
| 230 | .readSector: |
---|
| 231 | mov cx,bx |
---|
| 232 | inc cx |
---|
[181] | 233 | |
---|
[179] | 234 | mov bl,dl ; setup bl with proper values for read loop (bh comes later) |
---|
| 235 | |
---|
| 236 | ;---------------------------------------------------------------------- |
---|
| 237 | ; |
---|
| 238 | ; Timeout |
---|
| 239 | ; |
---|
| 240 | ; During read, we first poll in a tight loop, interrupts off, for the next character to come in |
---|
| 241 | ; If that loop completes, then we assume there is a long delay involved, turn interrupts back on |
---|
| 242 | ; and wait for a given number of timer ticks to pass. |
---|
| 243 | ; |
---|
| 244 | ; To save code space, we use the contents of DL to decide which byte in the word to return for reading. |
---|
| 245 | ; |
---|
| 246 | .readTimeout: |
---|
| 247 | push cx |
---|
| 248 | xor cx,cx |
---|
[181] | 249 | .readTimeoutLoop: |
---|
[179] | 250 | push dx |
---|
| 251 | or dl,SerialCommand_UART_lineStatus |
---|
| 252 | in al,dx |
---|
| 253 | pop dx |
---|
| 254 | shr al,1 |
---|
| 255 | jc .readTimeoutComplete |
---|
| 256 | loop .readTimeoutLoop |
---|
| 257 | sti |
---|
| 258 | mov bh,1 |
---|
| 259 | call SerialCommand_WaitAndPoll_Init |
---|
[181] | 260 | cli |
---|
[179] | 261 | .readTimeoutComplete: |
---|
| 262 | mov bh,bl |
---|
| 263 | or bh,SerialCommand_UART_lineStatus |
---|
[181] | 264 | |
---|
[179] | 265 | pop cx |
---|
| 266 | test dl,1 |
---|
| 267 | jz .readByte1Ready |
---|
| 268 | jmp .readByte2Ready |
---|
| 269 | |
---|
| 270 | ;---------------------------------------------------------------------------- |
---|
| 271 | ; |
---|
| 272 | ; Read Block (without interrupts, used when there is a FIFO, high speed) |
---|
| 273 | ; |
---|
[181] | 274 | ; NOTE: This loop is very time sensitive. Literally, another instruction |
---|
[179] | 275 | ; cannot be inserted into this loop without us falling behind at high |
---|
[181] | 276 | ; speed (460.8K baud) on a 4.77Mhz 8088, making it hard to receive |
---|
[179] | 277 | ; a full 512 byte block. |
---|
| 278 | ; |
---|
[181] | 279 | .readLoop: |
---|
| 280 | stosw ; store word in caller's data buffer |
---|
| 281 | |
---|
[179] | 282 | add bp, ax ; update Fletcher's checksum |
---|
| 283 | adc bp, 0 |
---|
| 284 | add si, bp |
---|
| 285 | adc si, 0 |
---|
| 286 | |
---|
[181] | 287 | mov dl,bh |
---|
| 288 | in al,dx |
---|
[179] | 289 | shr al,1 ; data ready (byte 1)? |
---|
[181] | 290 | mov dl,bl ; get ready to read data |
---|
[179] | 291 | jnc .readTimeout ; nope not ready, update timeouts |
---|
[181] | 292 | |
---|
| 293 | ; |
---|
[179] | 294 | ; Entry point after initial timeout. We enter here so that the checksum word |
---|
| 295 | ; is not stored (and is left in AX after the loop is complete). |
---|
[181] | 296 | ; |
---|
| 297 | .readByte1Ready: |
---|
[179] | 298 | in al, dx ; read data byte 1 |
---|
| 299 | |
---|
| 300 | mov ah, al ; store byte in ah for now |
---|
[181] | 301 | |
---|
[179] | 302 | ; |
---|
[181] | 303 | ; note the placement of this reset of dl to bh, and that it is |
---|
| 304 | ; before the return, which is assymetric with where this is done |
---|
| 305 | ; above for byte 1. The value of dl is used by the timeout routine |
---|
| 306 | ; to know which byte to return to (.read_byte1_ready or |
---|
[179] | 307 | ; .read_byte2_ready) |
---|
| 308 | ; |
---|
[181] | 309 | mov dl,bh |
---|
| 310 | |
---|
[179] | 311 | in al,dx |
---|
| 312 | shr al,1 ; data ready (byte 2)? |
---|
| 313 | jnc .readTimeout |
---|
[181] | 314 | .readByte2Ready: |
---|
| 315 | mov dl,bl |
---|
[179] | 316 | in al, dx ; read data byte 2 |
---|
| 317 | |
---|
| 318 | xchg al, ah ; ah was holding byte 1, reverse byte order |
---|
[181] | 319 | |
---|
[179] | 320 | loop .readLoop |
---|
| 321 | |
---|
[181] | 322 | sti ; interrupts back on ASAP, if we turned them off |
---|
| 323 | |
---|
[179] | 324 | ; |
---|
| 325 | ; Compare checksums |
---|
[181] | 326 | ; |
---|
[179] | 327 | xor bp,si |
---|
| 328 | cmp ax,bp |
---|
| 329 | jnz SerialCommand_OutputWithParameters_Error |
---|
| 330 | |
---|
[181] | 331 | |
---|
[179] | 332 | ;---------------------------------------------------------------------- |
---|
[181] | 333 | ; |
---|
[179] | 334 | ; Clear read buffer |
---|
| 335 | ; |
---|
| 336 | ; In case there are extra characters or an error in the FIFO, clear it out. |
---|
[181] | 337 | ; In theory the initialization of the UART registers above should have |
---|
[179] | 338 | ; taken care of this, but I have seen cases where this is not true. |
---|
| 339 | ; |
---|
| 340 | .clearBuffer: |
---|
[181] | 341 | mov dl,bh |
---|
[179] | 342 | in al,dx |
---|
[181] | 343 | mov dl,bl |
---|
[179] | 344 | test al,08fh |
---|
| 345 | jz .clearBufferComplete |
---|
| 346 | shr al,1 |
---|
[181] | 347 | in al,dx |
---|
[179] | 348 | jc .clearBuffer ; note CF from shr above |
---|
| 349 | jmp SerialCommand_OutputWithParameters_Error |
---|
[181] | 350 | |
---|
| 351 | .clearBufferComplete: |
---|
[179] | 352 | pop ax ; sector count and command byte |
---|
| 353 | dec al ; decrememnt sector count |
---|
| 354 | push ax ; save |
---|
| 355 | jz SerialCommand_OutputWithParameters_ReturnCodeInALCF ; CF clear from .clearBuffer test above |
---|
[181] | 356 | |
---|
[179] | 357 | cli ; interrupts back off for ACK byte to host |
---|
| 358 | ; (host could start sending data immediately) |
---|
| 359 | out dx,al ; ACK with next sector number |
---|
[181] | 360 | |
---|
[179] | 361 | jmp .nextSector ; all is well, time for next sector |
---|
| 362 | |
---|
| 363 | ;--------------------------------------------------------------------------- |
---|
| 364 | ; |
---|
| 365 | ; Cleanup, error reporting, and exit |
---|
| 366 | ; |
---|
[181] | 367 | |
---|
| 368 | ; |
---|
[179] | 369 | ; Used in situations where a call is underway, such as with SerialCommand_WaitAndPoll |
---|
[181] | 370 | ; |
---|
[179] | 371 | SerialCommand_OutputWithParameters_ErrorAndPop2Words: |
---|
| 372 | pop ax |
---|
| 373 | pop ax |
---|
| 374 | |
---|
[181] | 375 | SerialCommand_OutputWithParameters_Error: |
---|
| 376 | stc |
---|
[179] | 377 | mov al,1 |
---|
| 378 | |
---|
[181] | 379 | SerialCommand_OutputWithParameters_ReturnCodeInALCF: |
---|
| 380 | sti |
---|
[179] | 381 | mov ah,al |
---|
| 382 | |
---|
| 383 | pop bp ; recover ax from stack, throw away |
---|
| 384 | |
---|
| 385 | pop es |
---|
| 386 | pop bp |
---|
| 387 | pop di |
---|
| 388 | pop si |
---|
| 389 | |
---|
| 390 | ret |
---|
| 391 | |
---|
[150] | 392 | ;-------------------------------------------------------------------- |
---|
[179] | 393 | ; SerialCommand_WaitAndPoll |
---|
| 394 | ; |
---|
| 395 | ; Parameters: |
---|
| 396 | ; BH: UART_LineStatus bit to test (20h for write, or 1h for read) |
---|
| 397 | ; DX: Port address (OK if already incremented to UART_lineStatus) |
---|
| 398 | ; Stack: 2 words on the stack below the command/count word |
---|
| 399 | ; Returns: |
---|
| 400 | ; Returns when desired UART_LineStatus bit is cleared |
---|
| 401 | ; Jumps directly to error exit if timeout elapses (and cleans up stack) |
---|
[181] | 402 | ; Corrupts registers: |
---|
[179] | 403 | ; CX, flags |
---|
| 404 | ;-------------------------------------------------------------------- |
---|
| 405 | |
---|
| 406 | SerialCommand_WaitAndPoll_SoftDelayTicks EQU 20 |
---|
| 407 | |
---|
[181] | 408 | ALIGN JUMP_ALIGN |
---|
[179] | 409 | SerialCommand_WaitAndPoll_Init: |
---|
| 410 | mov cl,SerialCommand_WaitAndPoll_SoftDelayTicks |
---|
| 411 | call Timer_InitializeTimeoutWithTicksInCL |
---|
| 412 | ; fall-through |
---|
[181] | 413 | |
---|
[179] | 414 | SerialCommand_WaitAndPoll: |
---|
| 415 | call Timer_SetCFifTimeout |
---|
| 416 | jc SerialCommand_OutputWithParameters_ErrorAndPop2Words |
---|
| 417 | push dx |
---|
| 418 | push ax |
---|
| 419 | or dl,SerialCommand_UART_lineStatus |
---|
| 420 | in al,dx |
---|
| 421 | test al,bh |
---|
| 422 | pop ax |
---|
| 423 | pop dx |
---|
| 424 | jz SerialCommand_WaitAndPoll |
---|
| 425 | ; fall-through |
---|
[181] | 426 | |
---|
| 427 | SerialCommand_WaitAndPoll_Done: |
---|
[179] | 428 | ret |
---|
| 429 | |
---|
| 430 | ;-------------------------------------------------------------------- |
---|
| 431 | ; SerialCommand_WriteProtocol |
---|
| 432 | ; |
---|
| 433 | ; Parameters: |
---|
| 434 | ; ES:DI: Ptr to buffer |
---|
| 435 | ; BL: Words to write (1-255, or 0=256) |
---|
| 436 | ; BP/SI: Initialized for Checksum (-1 in each) |
---|
| 437 | ; DX: I/O Port |
---|
| 438 | ; Returns: |
---|
| 439 | ; BP/SI: Checksum for written bytes, compared against ACK from server in .readLoop |
---|
| 440 | ; Corrupts registers: |
---|
| 441 | ; AX, BX, CX, DI |
---|
| 442 | ;-------------------------------------------------------------------- |
---|
[150] | 443 | ALIGN JUMP_ALIGN |
---|
[179] | 444 | SerialCommand_WriteProtocol: |
---|
| 445 | mov bh,20h |
---|
[181] | 446 | |
---|
[179] | 447 | .writeLoop: |
---|
| 448 | test bh,1 |
---|
| 449 | jnz SerialCommand_WaitAndPoll_Done |
---|
[181] | 450 | |
---|
[179] | 451 | mov ax,[es:di] ; fetch next word |
---|
| 452 | inc di |
---|
| 453 | inc di |
---|
[181] | 454 | |
---|
[179] | 455 | add bp,ax ; update checksum |
---|
| 456 | adc bp,0 |
---|
| 457 | add si,bp |
---|
| 458 | adc si,0 |
---|
[150] | 459 | |
---|
[179] | 460 | .writeLoopChecksum: |
---|
| 461 | call SerialCommand_WaitAndPoll_Init |
---|
[181] | 462 | |
---|
[179] | 463 | out dx,al ; output first byte |
---|
[150] | 464 | |
---|
[179] | 465 | call SerialCommand_WaitAndPoll |
---|
[181] | 466 | |
---|
[179] | 467 | mov al,ah ; output second byte |
---|
| 468 | out dx,al |
---|
| 469 | |
---|
| 470 | dec bl |
---|
| 471 | jnz .writeLoop |
---|
[181] | 472 | |
---|
[179] | 473 | inc bh |
---|
[181] | 474 | |
---|
[179] | 475 | mov ax,bp ; merge checksum for possible write (last loop) |
---|
[181] | 476 | xor ax,si |
---|
| 477 | |
---|
[179] | 478 | jmp .writeLoopChecksum |
---|
| 479 | |
---|
| 480 | |
---|
| 481 | ; To return the port number and baud rate to the FinalizeDPT routine, we |
---|
| 482 | ; stuff the value in a "vendor" specific area of the 512-byte IdentifyDevice |
---|
| 483 | ; sector. |
---|
| 484 | ; |
---|
| 485 | SerialCommand_IdentifyDevice_PackedPortAndBaud equ (157*2) |
---|
| 486 | |
---|
| 487 | ;-------------------------------------------------------------------- |
---|
| 488 | ; SerialCommand_IdentifyDeviceToBufferInESSIwithDriveSelectByteInBH |
---|
| 489 | ; Parameters: |
---|
| 490 | ; BH: Drive Select byte for Drive and Head Select Register |
---|
| 491 | ; DS: Segment to RAMVARS |
---|
| 492 | ; ES:SI: Ptr to buffer to receive 512-byte IDE Information |
---|
| 493 | ; CS:BP: Ptr to IDEVARS |
---|
| 494 | ; Returns: |
---|
| 495 | ; AH: INT 13h Error Code |
---|
| 496 | ; CF: Cleared if success, Set if error |
---|
| 497 | ; Corrupts registers: |
---|
| 498 | ; AL, BL, CX, DX, SI, DI, ES |
---|
| 499 | ;-------------------------------------------------------------------- |
---|
| 500 | ALIGN JUMP_ALIGN |
---|
| 501 | SerialCommand_IdentifyDeviceToBufferInESSIwithDriveSelectByteInBH: |
---|
| 502 | |
---|
[199] | 503 | mov dx,[cs:bp+IDEVARS.bSerialCOMDigit] |
---|
[196] | 504 | test dl,dl |
---|
[179] | 505 | jz SerialCommand_AutoSerial |
---|
| 506 | |
---|
[199] | 507 | xchg dh,dl ; dh (the COM character to print) will be transmitted to the server, |
---|
| 508 | ; so we know this is not an auto detect |
---|
| 509 | |
---|
[179] | 510 | ; fall-through |
---|
[181] | 511 | SerialCommand_IdentifyDeviceInDL_DriveInBH: |
---|
[179] | 512 | |
---|
| 513 | push bp ; setup fake IDEREGS_AND_INTPACK |
---|
| 514 | |
---|
| 515 | push dx |
---|
| 516 | |
---|
| 517 | mov cl,1 ; 1 sector to move |
---|
| 518 | push cx |
---|
| 519 | |
---|
| 520 | mov bl,0a0h ; protocol command to ah and onto stack with bh |
---|
| 521 | mov ah,bl |
---|
[181] | 522 | |
---|
[179] | 523 | push bx |
---|
| 524 | |
---|
| 525 | mov bp,sp |
---|
| 526 | |
---|
| 527 | call SerialCommand_OutputWithParameters_DeviceInDL |
---|
| 528 | |
---|
| 529 | pop bx |
---|
[181] | 530 | |
---|
| 531 | pop cx |
---|
[179] | 532 | pop dx |
---|
| 533 | |
---|
| 534 | pop bp |
---|
| 535 | |
---|
[181] | 536 | ; place packed port/baud in vendor area of packet, read by FinalizeDPT |
---|
| 537 | mov byte [es:si+SerialCommand_IdentifyDevice_PackedPortAndBaud], dl |
---|
[179] | 538 | |
---|
| 539 | ret |
---|
| 540 | |
---|
| 541 | ;---------------------------------------------------------------------- |
---|
| 542 | ; |
---|
| 543 | ; SerialCommand_AutoSerial |
---|
| 544 | ; |
---|
| 545 | ; When the SerialAuto IDEVARS entry is used, scans the COM ports on the machine for a possible serial connection. |
---|
[181] | 546 | ; |
---|
| 547 | |
---|
[199] | 548 | SerialCommand_ScanPortAddresses: db DEVICE_SERIAL_COM7 >> 2 |
---|
| 549 | db DEVICE_SERIAL_COM6 >> 2 |
---|
| 550 | db DEVICE_SERIAL_COM5 >> 2 |
---|
| 551 | db DEVICE_SERIAL_COM4 >> 2 |
---|
| 552 | db DEVICE_SERIAL_COM3 >> 2 |
---|
| 553 | db DEVICE_SERIAL_COM2 >> 2 |
---|
| 554 | db DEVICE_SERIAL_COM1 >> 2 |
---|
| 555 | db 0 |
---|
[179] | 556 | |
---|
[181] | 557 | ALIGN JUMP_ALIGN |
---|
| 558 | SerialCommand_AutoSerial: |
---|
[179] | 559 | mov di,SerialCommand_ScanPortAddresses-1 |
---|
[181] | 560 | |
---|
[179] | 561 | .nextPort: |
---|
| 562 | inc di ; load next port address |
---|
| 563 | mov dl,[cs:di] |
---|
[181] | 564 | |
---|
[179] | 565 | mov dh,0 ; shift from one byte to two |
---|
[181] | 566 | eSHL_IM dx, 2 |
---|
[179] | 567 | jz .exitNotFound |
---|
| 568 | |
---|
| 569 | ; |
---|
| 570 | ; Test for COM port presence, write to and read from registers |
---|
[181] | 571 | ; |
---|
| 572 | push dx |
---|
[179] | 573 | add dl,SerialCommand_UART_lineControl |
---|
| 574 | mov al, 09ah |
---|
| 575 | out dx, al |
---|
| 576 | in al, dx |
---|
| 577 | pop dx |
---|
| 578 | cmp al, 09ah |
---|
[181] | 579 | jnz .nextPort |
---|
[179] | 580 | |
---|
| 581 | mov al, 0ch |
---|
| 582 | out dx, al |
---|
| 583 | in al, dx |
---|
| 584 | cmp al, 0ch |
---|
| 585 | jnz .nextPort |
---|
| 586 | |
---|
| 587 | ; |
---|
| 588 | ; Pack into dl, baud rate starts at 0 |
---|
[181] | 589 | ; |
---|
[199] | 590 | add dx,-(DEVICE_SERIAL_PACKEDPORTANDBAUD_STARTINGPORT) |
---|
| 591 | shr dx,1 ; dh is zero at this point, and will be sent to the server, |
---|
| 592 | ; so we know this is an auto detect |
---|
[181] | 593 | |
---|
[179] | 594 | jmp .testFirstBaud |
---|
| 595 | |
---|
| 596 | ; |
---|
| 597 | ; Walk through 4 possible baud rates |
---|
[181] | 598 | ; |
---|
| 599 | .nextBaud: |
---|
[179] | 600 | inc dx |
---|
| 601 | test dl,3 |
---|
| 602 | jz .nextPort |
---|
[181] | 603 | |
---|
| 604 | .testFirstBaud: |
---|
[179] | 605 | call SerialCommand_IdentifyDeviceInDL_DriveInBH |
---|
| 606 | jc .nextBaud |
---|
| 607 | |
---|
| 608 | ret |
---|
[181] | 609 | |
---|
[179] | 610 | .exitNotFound: |
---|
[181] | 611 | stc |
---|
[179] | 612 | mov ah,1 |
---|
| 613 | |
---|
| 614 | ret |
---|