source: xtideuniversalbios/trunk/XTIDE_Universal_BIOS/Src/Device/IDE/IdeDPT.asm@ 592

Last change on this file since 592 was 592, checked in by Krister Nordvall, 6 years ago

Changes:

  • The problem with NASM in the previous revision (r591) has been fixed.
  • The colors used by the boot menu and hotkey bar can now be customized by selecting one of a number of pre-defined color themes. Suggestions for additional themes are more than welcome!
  • Large builds are now 10 KB. Small builds are still 8 KB with the exception of the Tiny build which is now 4 KB. In other words, builds are now as small as possible to make it easier to combine them with other BIOSes.
  • Added code to the library to improve drive error handling. XTIDECFG can now handle "Drive Not Ready" errors.
  • Fixed a couple of potential bugs in AtaID.asm (AtaID_GetMaxPioModeToAXandMinCycleTimeToCX); 1) ATA1.bPioMode was treated as a WORD variable. 2) ATA2.bPIOSupp was assumed to be non-zero which would result in PIO mode 3 being returned if the assumption was wrong.
  • Made the same changes in the equivalent function used by BIOSDRVS (DisplayPioModeInformationUsingAtaInfoFromDSBX in AtaInfo.asm).
  • Fixed a bug from r587 in PDC20x30.asm in PDC20x30_GetMaxPioModeToALandMinPioCycleTimeToBX.
  • Fixed a bug from r523 in XTIDECFG where Auto Configure would only set the IRQ on one IDE interface on AT-builds.
  • XTIDECFG will now restore the default settings for the "Serial port virtual device" when reselecting it in the list of device types. This makes it behave consistently for all device types.
  • The eAAM macro is now used regardless if USE_UNDOC_INTEL is defined or not because it is apparently supported on all processors including the NEC V20/V30 CPUs.
  • Renamed the EXCLUDE_FROM_XTIDE_UNIVERSAL_BIOS define to EXCLUDE_FROM_XUB.
  • Added a define to exclude unused library code from BIOSDRVS (EXCLUDE_FROM_BIOSDRVS). This makes it a lot smaller than in previous revisions.
  • All unnecessary CLD-instructions are now under a new define 'CLD_NEEDED' which is only enabled for the BIOS. It is disabled for XTIDECFG and BIOSDRVS but can be enabled if needed by adding this define to the respective makefile. This change was made because these unnecessary instructions are wasteful and should never be needed. In fact, they only serve to hide bugs (in other peoples code) which I strongly believe should be avoided. I recommend people making their own BIOSes from source to not use this define as it's extremely unlikely to be needed.
  • Updated the copyright info in SerDrive and changed an URL to point to the new site.
  • Updated the copyright info and version number in BIOSDRVS.
  • Updated the copyright info in XTIDECFG.
  • Optimizations in general.
File size: 5.0 KB
Line 
1; Project name : XTIDE Universal BIOS
2; Description : Sets IDE Device specific parameters to DPT.
3
4;
5; XTIDE Universal BIOS and Associated Tools
6; Copyright (C) 2009-2010 by Tomi Tilli, 2011-2013 by XTIDE Universal BIOS Team.
7;
8; This program is free software; you can redistribute it and/or modify
9; it under the terms of the GNU General Public License as published by
10; the Free Software Foundation; either version 2 of the License, or
11; (at your option) any later version.
12;
13; This program is distributed in the hope that it will be useful,
14; but WITHOUT ANY WARRANTY; without even the implied warranty of
15; MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16; GNU General Public License for more details.
17; Visit http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
18;
19
20; Section containing code
21SECTION .text
22
23;--------------------------------------------------------------------
24; IdeDPT_Finalize
25; Parameters:
26; DS:DI: Ptr to Disk Parameter Table
27; ES:SI: Ptr to 512-byte ATA information read from the drive
28; CS:BP: Ptr to IDEVARS for the controller
29; Returns:
30; CF: Clear, IDE interface only supports hard disks
31; Corrupts registers:
32; AX, BX, CX, DX
33;--------------------------------------------------------------------
34IdeDPT_Finalize:
35
36%ifdef MODULE_POWER_MANAGEMENT
37;--------------------------------------------------------------------
38; .DetectPowerManagementSupport
39; Parameters:
40; DS:DI: Ptr to Disk Parameter Table
41; ES:SI: Ptr to 512-byte ATA information read from the drive
42; Returns:
43; Nothing
44; Corrupts registers:
45; AL
46;--------------------------------------------------------------------
47.DetectPowerManagementSupport:
48 mov al, [es:si+ATA6.wSetSup82]
49 and al, A6_wSetSup82_POWERMAN ; A6_wSetSup82_POWERMAN (bit 3) is the same
50 or [di+DPT.bFlagsHigh], al ; bit as FLGH_DPT_POWER_MANAGEMENT_SUPPORTED
51%endif ; MODULE_POWER_MANAGEMENT
52
53
54;--------------------------------------------------------------------
55; .StoreDeviceType
56; Parameters:
57; DS:DI: Ptr to Disk Parameter Table
58; CS:BP: Ptr to IDEVARS for the controller
59; Returns:
60; Nothing
61; Corrupts registers:
62; AL
63;--------------------------------------------------------------------
64.StoreDeviceType:
65 call IdeDPT_StoreDeviceTypeToDPTinDSDIfromIdevarsInCSBP
66
67
68;--------------------------------------------------------------------
69; .StoreBlockMode
70; Parameters:
71; DS:DI: Ptr to Disk Parameter Table
72; Returns:
73; Nothing
74; Corrupts registers:
75; Nothing
76;--------------------------------------------------------------------
77.StoreBlockMode:
78 mov BYTE [di+DPT_ATA.bBlockSize], 1
79
80
81%ifdef MODULE_ADVANCED_ATA
82;--------------------------------------------------------------------
83; .StorePioModeAndTimings
84; Parameters:
85; DS:DI: Ptr to Disk Parameter Table
86; ES:SI: Ptr to 512-byte ATA information read from the drive
87; CS:BP: Ptr to IDEVARS for the controller
88; Returns:
89; Nothing
90; Corrupts registers:
91; AX, BX, CX
92;--------------------------------------------------------------------
93.StorePioMode:
94 call AtaID_GetMaxPioModeToAXandMinCycleTimeToCX
95 mov [di+DPT_ADVANCED_ATA.wMinPioCycleTime], cx
96 mov [di+DPT_ADVANCED_ATA.bPioMode], al
97 or [di+DPT.bFlagsHigh], ah
98
99
100;--------------------------------------------------------------------
101; .DetectAdvancedIdeController
102; Parameters:
103; DS:DI: Ptr to Disk Parameter Table
104; ES:SI: Ptr to 512-byte ATA information read from the drive
105; CS:BP: Ptr to IDEVARS for the controller
106; Returns:
107; Nothing
108; Corrupts registers:
109; AX, BX, CX, DX
110;--------------------------------------------------------------------
111.DetectAdvancedIdeController:
112 mov bx, [di+DPT.wBasePort]
113 call AdvAtaInit_DetectControllerForIdeBaseInBX
114 mov [di+DPT_ADVANCED_ATA.wControllerID], ax ; Store zero if none detected
115 mov [di+DPT_ADVANCED_ATA.wControllerBasePort], dx
116 jnc SHORT .NoAdvancedControllerDetected
117
118 ; Use highest common PIO mode from controller and drive.
119 ; Many VLB controllers support PIO modes up to 2.
120 call AdvAtaInit_GetControllerMaxPioModeToALandMinPioCycleTimeToBX
121 jnz SHORT .ChangeTo32bitDevice
122
123 and [di+DPT.bFlagsHigh], ah ; Mask off FLGH_DPT_IORDY if IORDY not supported
124 MIN_U [di+DPT_ADVANCED_ATA.bPioMode], al
125 mov [di+DPT_ADVANCED_ATA.wMinPioCycleTime], bx
126
127 ; We have detected 32-bit controller so change Device Type since
128 ; it might have been set to 16-bit on IDEVARS
129.ChangeTo32bitDevice:
130 mov BYTE [di+DPT_ATA.bDevice], DEVICE_32BIT_ATA
131.NoAdvancedControllerDetected:
132%endif ; MODULE_ADVANCED_ATA
133
134
135; End DPT
136 clc
137 ret
138
139
140;--------------------------------------------------------------------
141; IdeDPT_StoreDeviceTypeToDPTinDSDIfromIdevarsInCSBP
142; Parameters:
143; DS:DI: Ptr to Disk Parameter Table
144; CS:BP: Ptr to IDEVARS for the controller
145; Returns:
146; Nothing
147; Corrupts registers:
148; AL
149;--------------------------------------------------------------------
150IdeDPT_StoreDeviceTypeToDPTinDSDIfromIdevarsInCSBP:
151 mov al, [cs:bp+IDEVARS.bDevice]
152 mov [di+DPT_ATA.bDevice], al
153 ret
Note: See TracBrowser for help on using the repository browser.