source: xtideuniversalbios/trunk/Assembly_Library/Src/File/Drive.asm@ 591

Last change on this file since 591 was 589, checked in by Krister Nordvall, 8 years ago

Changes:

  • BIOS: Fixed a purely cosmetic bug from r542 where, in builds containing MODULE_EBIOS, the boot menu would display an incorrect drive size (0.4 kB with MODULE_STRINGS_COMPRESSED or 0.5 kB without) for old drives with no support for LBA.
  • Fixed a bug from r392 where Vision_DetectAndReturnIDinAXandPortInDXifControllerPresent would return the ID in AL instead of AH (if DANGEROUS_DETECTION had been defined).
  • Fixed a bug from r587 in AdvAtaInit.asm that would prevent detection of QDI Vision controllers.
  • Also changed how the QDI Vision IDs are defined (removed the need for shifting) to avoid confusion. This fixed a potential bug from r587 in AdvAtaInit.asm where some IDs were not being shifted.
  • Fixed a bug in PDC20x30.asm from r587 where GetPdcIDtoAX would not return with the IDE base port in DX so DisablePdcProgrammingMode would fail.
  • Made some changes to ModuleDependency.inc and other files so that MODULE_ADVANCED_ATA now requires USE_386. Consequently it is no longer included in the regular AT-builds, only in the 386_8k-build.
  • Moved the UNROLL_SECTORS_IN_CX_TO_xWORDS macros from IDE_8bit.inc to IdeIO.inc which means it's now possible to build a BIOS without MODULE_8BIT_IDE.
  • XTIDECFG: Added a minimum DOS version check (since it needs DOS version 2+) to allow the program to quit gracefully in the unlikely scenario where someone tries to run it under DOS version 1.
  • Made some changes to Drive.asm to improve drive enumeration. The old method using GET_DOS_DRIVE_PARAMETER_BLOCK_FOR_SPECIFIC_DRIVE worked well in Windows XP but not in Windows 98 SE (in Windows or in DOS mode). The two problems were; 1) The function call would access the drives which on single floppy drive systems would cause Windows to swap between A: and B: (throwing a blue screen asking the user to insert a disk etc). 2) Only floppy drives and FAT16 drives would be available in the list of drives, no FAT32/optical/network drives.
  • Improved code in IdeControllerMenu.asm so that the default port addresses for all IDE interfaces are now restored when (re-)selecting the (same) type of IDE device.
  • Also made it impossible to select a device type unless the required module is included in the loaded BIOS.
  • The version check done when loading a BIOS now uses the FLASH_SIGNATURE definition from Version.inc. Any changes affecting RomVars now only requires updating that definition. This means that changes to RomVars must be implemented in both the BIOS and XTIDECFG before being committed to the repository.
  • Added a compatibility fix for 3Com 3C503 cards to the ROM checksumming code in Buffers.asm (Buffers_GenerateChecksum).
  • SerDrive: Made some minor changes to file names and paths to improve compatibility with case sensitive environments.
  • BIOSDRVS: Made a minor size optimization which as a side effect also makes it compatible with all DOS versions including DOS version 1.
  • Library: Renamed the WAIT_RETRACE_IF_NECESSARY_THEN macro to CALL_WAIT_FOR_RETRACE_IF_NECESSARY_THEN and made a tail-call-optimized version of it (JMP_WAIT_FOR_RETRACE_IF_NECESSARY_THEN).
  • A speed optimization to the eRCL_IM macro for 386 and higher. This change breaks emulation in the sense that the macro will fail when given a memory operand as the first parameter.
  • Other minor optimizations and fixes.
File size: 5.6 KB
RevLine 
[41]1; Project name : Assembly Library
2; Description : Functions for accessing drives.
3
[376]4;
[526]5; XTIDE Universal BIOS and Associated Tools
6; Copyright (C) 2009-2010 by Tomi Tilli, 2011-2013 by XTIDE Universal BIOS Team.
[376]7;
8; This program is free software; you can redistribute it and/or modify
9; it under the terms of the GNU General Public License as published by
10; the Free Software Foundation; either version 2 of the License, or
11; (at your option) any later version.
[526]12;
[376]13; This program is distributed in the hope that it will be useful,
14; but WITHOUT ANY WARRANTY; without even the implied warranty of
15; MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
[526]16; GNU General Public License for more details.
[376]17; Visit http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
18;
[41]19
20; Section containing code
21SECTION .text
22
23;--------------------------------------------------------------------
24; Drive_GetNumberOfAvailableDrivesToAX
25; Parameters:
26; Nothing
27; Returns:
28; AX: Number of available drives
29; Corrupts registers:
30; Nothing
31;--------------------------------------------------------------------
32ALIGN JUMP_ALIGN
33Drive_GetNumberOfAvailableDrivesToAX:
34 push dx
35 push cx
36
37 call Drive_GetFlagsForAvailableDrivesToDXAX
38 call Bit_GetSetCountToCXfromDXAX
39 xchg ax, cx
40
41 pop cx
42 pop dx
43 ret
44
45
46;--------------------------------------------------------------------
47; Drive_GetFlagsForAvailableDrivesToDXAX
48; Parameters:
49; Nothing
50; Returns:
51; DX:AX: Flags containing valid drives (bit 0 = drive A, bit 1 = drive B ...)
52; Corrupts registers:
53; Nothing
54;--------------------------------------------------------------------
55ALIGN JUMP_ALIGN
56Drive_GetFlagsForAvailableDrivesToDXAX:
57 push cx
58 push bx
59 mov dx, DosCritical_HandlerToIgnoreAllErrors
60 call DosCritical_InstallNewHandlerFromCSDX
61
62 call .GetNumberOfPotentiallyValidDriveLettersToCX
63 xor bx, bx
64 xor ax, ax ; Temporary use BX:AX for flags
[133]65 cwd ; Start from drive 0
[41]66 call .CheckDriveValidityUntilCXisZero
67 mov dx, bx ; Flags now in DX:AX
68
69 call DosCritical_RestoreDosHandler
70 pop bx
71 pop cx
72 ret
73
74;--------------------------------------------------------------------
75; .GetNumberOfPotentiallyValidDriveLettersToCX
76; Parameters:
77; Nothing
78; Returns:
79; CX: Number of potentially valid drive letters available
80; Corrupts registers:
81; AX, DX
82;--------------------------------------------------------------------
83ALIGN JUMP_ALIGN
84.GetNumberOfPotentiallyValidDriveLettersToCX:
85 call Drive_GetDefaultToAL
86 xchg dx, ax ; Default drive to DL
87 call Drive_SetDefaultFromDL
[589]88 cmp al, 32 ; Number of potentially valid drive letters available
89 jb SHORT .Below32
90 mov al, 32
91.Below32:
92 cbw
93 xchg cx, ax
[41]94 ret
95
96;--------------------------------------------------------------------
97; .CheckDriveValidityUntilCXisZero
98; Parameters:
99; CX: Number of potentially valid drive letters left
100; DL: Drive number (00h=A:, 01h=B: ...)
101; BX:AX: Flags for drive numbers
102; Returns:
103; BX:AX: Flags for valid drive numbers
104; Corrupts registers:
105; CX, DX
106;--------------------------------------------------------------------
107ALIGN JUMP_ALIGN
108.CheckDriveValidityUntilCXisZero:
109 call .IsValidDriveNumberInDL
110 jnz SHORT .PrepareToCheckNextDrive
111 call .SetFlagToBXAXfromDriveInDL
112ALIGN JUMP_ALIGN
113.PrepareToCheckNextDrive:
114 inc dx
115 loop .CheckDriveValidityUntilCXisZero
116 ret
117
118;--------------------------------------------------------------------
119; .IsValidDriveNumberInDL
120; Parameters:
121; DL: Drive number (00h=A:, 01h=B: ...)
122; Returns:
123; ZF: Set if drive number is valid
124; Cleared if drive number is invalid
125; Corrupts registers:
126; Nothing
127;--------------------------------------------------------------------
128ALIGN JUMP_ALIGN
129.IsValidDriveNumberInDL:
130 push ds
131 push bx
132 push ax
133
134 inc dx ; Default drive is 00h and first drive is 01h
[589]135 mov ax, CHECK_IF_BLOCK_DEVICE_REMOTE ; Needs DOS 3.1+
136 mov bx, dx
137 push dx
138 int DOS_INTERRUPT_21h
139 pop dx
140 jnc SHORT .DriveIsValid
141 cmp ax, ERR_DOS_INVALID_DRIVE
142 je SHORT .DriveIsNotValid
143 ; Fall back to old method if ERR_DOS_FUNCTION_NUMBER_INVALID
144
[41]145 mov ah, GET_DOS_DRIVE_PARAMETER_BLOCK_FOR_SPECIFIC_DRIVE
146 int DOS_INTERRUPT_21h
[589]147.DriveIsValid:
148.DriveIsNotValid:
[41]149 dec dx
150 test al, al
151
152 pop ax
153 pop bx
154 pop ds
155 ret
156
157;--------------------------------------------------------------------
158; .SetFlagToBXAXfromDriveInDL
159; Parameters:
160; DL: Drive number (0...31)
161; BX:AX: Flags containing drive numbers
162; Returns:
163; BX:AX: Flags with wanted drive bit set
164; Corrupts registers:
165; Nothing
166;--------------------------------------------------------------------
167ALIGN JUMP_ALIGN
168.SetFlagToBXAXfromDriveInDL:
169 push cx
170
171 mov cl, dl
172 xchg dx, bx
173 call Bit_SetToDXAXfromIndexInCL
174 xchg bx, dx
175
176 pop cx
177 ret
178
179
180;--------------------------------------------------------------------
181; Drive_GetDefaultToAL
182; Parameters:
183; Nothing
184; Returns:
185; AL: Current default drive (00h=A:, 01h=B: ...)
186; Corrupts registers:
187; AH
188;--------------------------------------------------------------------
189ALIGN JUMP_ALIGN
190Drive_GetDefaultToAL:
191 mov ah, GET_CURRENT_DEFAULT_DRIVE
[133]192 SKIP2B f ; cmp ax, <next instruction>
193 ; Fall to Drive_SetDefaultFromDL
[41]194
195
196;--------------------------------------------------------------------
197; Drive_SetDefaultFromDL
198; Parameters:
199; DL: New default drive (00h=A:, 01h=B: ...)
200; Returns:
201; AL: Number of potentially valid drive letters available
202; Corrupts registers:
203; AH
204;--------------------------------------------------------------------
205Drive_SetDefaultFromDL:
206 mov ah, SELECT_DEFAULT_DRIVE
207 int DOS_INTERRUPT_21h
208 ret
Note: See TracBrowser for help on using the repository browser.