source: xtideuniversalbios/trunk/XTIDE_Universal_BIOS_Configurator_v2/Src/Strings.asm @ 605

Last change on this file since 605 was 605, checked in by krille_n_, 3 years ago

Changes:

  • The "Remove other hard drives" option in the Boot settings menu in XTIDECFG is now exposed in all BIOS builds. This is needed because the system BIOS in at least two Zenith computer models (Z-161 and Z-171) does not clear the BDA HD count which causes it to increment on warm boot. Running "Auto Configure" in XTIDECFG now also tries to identify these machines by doing a CRC check on the system BIOS and sets the option to YES if a match is found.
  • WORD_ALIGN is now 2 for XT builds. This should benefit XT class machines with 8086 and NEC V30 CPU:s and the cost is negligible (1 byte for the XT BIOS builds and 12 bytes for XTIDECFG.COM).
  • Other minor optimizations.
File size: 31.0 KB
Line 
1; Project name  :   XTIDE Universal BIOS Configurator v2
2; Description   :   All strings.
3
4;
5; XTIDE Universal BIOS and Associated Tools
6; Copyright (C) 2009-2010 by Tomi Tilli, 2011-2013 by XTIDE Universal BIOS Team.
7;
8; This program is free software; you can redistribute it and/or modify
9; it under the terms of the GNU General Public License as published by
10; the Free Software Foundation; either version 2 of the License, or
11; (at your option) any later version.
12;
13; This program is distributed in the hope that it will be useful,
14; but WITHOUT ANY WARRANTY; without even the implied warranty of
15; MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
16; GNU General Public License for more details.
17; Visit http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
18;
19
20; Section containing initialized data
21SECTION .data
22
23; DOS version check
24g_s$NotMinimumDosVersion:           db  LF,"This program requires DOS version 2 or higher.",LF,"$"
25
26; Menu title
27g_szProgramTitle:                   db  "Configuration and Flashing program for XTIDE Universal BIOS v2.0.0.",LF,CR,NULL
28g_szXtideUniversalBiosSignature:    db  FLASH_SIGNATURE,NULL
29g_szBiosIsNotLoaded:                db  "BIOS is not loaded!",NULL
30g_szEEPROM:                         db  "EEPROM",NULL
31g_szSourceAndTypeSeparator:         db  " : ",NULL
32g_szUnidentified:                   db  "Unidentified",NULL
33g_szUnsaved:                        db  " ",SINGLE_LEFT_HORIZONTAL_TO_VERTICAL,"Unsaved",SINGLE_RIGHT_HORIZONTAL_TO_VERTICAL,NULL
34
35; Item formatting
36g_szFormatItemWithoutValue:         db  "%c%s",NULL
37g_szFormatItemNameWithValue:        db  "%25s%-10S",NULL
38
39
40g_szNo:                             db  "No",NULL
41g_szMultichoiceBooleanFlag:         db  "No",LF
42g_szYes:                            db  "Yes",NULL
43
44; General Yes/No response type dialog messages
45g_szDlgExitToDos:       db  "Exit to DOS?",NULL
46g_szDlgSaveChanges:     db  "Do you want to save changes to XTIDE Universal BIOS image file?",NULL
47g_szDlgDriveNotReady:   db  "Drive not ready! Retry?",NULL
48
49; Generic dialog strings
50g_szNotificationDialog: db  "Notification.",NULL
51g_szErrorDialog:        db  "Error!",NULL
52g_szGenericDialogInfo:  db  "Press ENTER or ESC to close dialog.",NULL
53
54; Flashing related strings
55g_szFlashTitle:         db  "Flashing EEPROM, please wait.",NULL
56g_szErrEepromTooSmall:  db  "Image is too large for selected EEPROM type!",NULL
57g_szErrEepromPolling:   db  "Timeout when polling EEPROM.",LF
58                        db  "EEPROM was not flashed properly!",NULL
59g_szErrEepromVerify:    db  "EEPROM did not return the same byte that was written.",LF
60                        db  "EEPROM was not flashed properly!",NULL
61g_szPCFlashSuccessful:  db  "EEPROM was written successfully.",LF
62                        db  "Press any key to reboot.",NULL
63g_szForeignFlash:       db  "EEPROM was written successfully.",NULL
64
65
66; Strings for main menu
67g_szItemMainExitToDOS:  db  "Exit to DOS",NULL
68g_szItemMainLoadFile:   db  "Load BIOS from file",NULL
69g_szItemMainLoadROM:    db  "Load BIOS from EEPROM",NULL
70g_szItemMainLoadStngs:  db  "Load old settings from EEPROM",NULL
71g_szItemMainConfigure:  db  "Configure XTIDE Universal BIOS",NULL
72g_szItemMainFlash:      db  "Flash EEPROM",NULL
73g_szItemMainSave:       db  "Save BIOS back to original file",NULL
74g_szItemMainLicense:    db  "Copyright and License Information",NULL
75g_szItemMainHomePage:   db  "Web Links",NULL
76
77g_szDlgMainLoadROM:     db  "Successfully loaded XTIDE Universal BIOS from EEPROM.",NULL
78g_szDlgMainLoadStngs:   db  "Successfully loaded settings from EEPROM.",NULL
79g_szDlgMainLoadFile:    db  "Successfully loaded file for flashing.",NULL
80g_szDlgMainSaveFile:    db  "Successfully saved XTIDE Universal BIOS to file.",NULL
81g_szDlgMainFileTooBig:  db  "Selected file is too big to be loaded for flashing!",NULL
82g_szDlgMainLoadErr:     db  "Failed to load file!",NULL
83g_szDlgMainSaveErr:     db  "Failed to save file!",NULL
84g_szDlgFileTitle:       db  "Select file to be flashed.",NULL
85g_szDlgFileFilter:      db  "*.*",NULL
86
87g_szNfoMainExitToDOS:   db  "Quits XTIDE Universal BIOS Configurator.",NULL
88g_szNfoMainLoadFile:    db  "Load BIOS file to be configured or flashed.",NULL
89g_szNfoMainLoadROM:     db  "Load BIOS from EEPROM to be reconfigured.",NULL
90g_szNfoMainLoadStngs:   db  "Load old XTIDE Universal BIOS settings from EEPROM.",NULL
91g_szNfoMainConfigure:   db  "Configure XTIDE Universal BIOS settings.",NULL
92g_szNfoMainFlash:       db  "Flash loaded BIOS image to EEPROM.",NULL
93g_szNfoMainSave:        db  "Save BIOS changes back to original file from which it was loaded.",NULL
94g_szNfoMainLicense:     db  "XTIDE Universal BIOS and XTIDECFG Copyright (C) 2009-2010 by Tomi Tilli, 2011-2019 by XTIDE Universal BIOS Team."
95                        db  " Released under GNU GPL v2, with ABSOLUTELY NO WARRANTY. Press ENTER for more details...",NULL
96g_szNfoMainHomePage:    db  "Visit http://xtideuniversalbios.org (home page) and http://vcfed.org/forum (support)",NULL
97
98g_szHelpMainLicense:    db  "XTIDE Universal BIOS and XTIDECFG Configuration program are Copyright 2009-2010 by Tomi Tilli,"
99                        db  " 2011-2019 by XTIDE Universal BIOS Team. Released under GNU GPL v2. This software comes with ABSOLUTELY NO WARRANTY."
100                        db  " This is free software, and you are welcome to redistribute it under certain conditions."
101                        db  " See the LICENSE.TXT file that was included with this distribution,"
102                        db  " visit http://www.gnu.org/licenses/ gpl-2.0.html, or visit http://xtideuniversalbios.org.",NULL
103
104; Strings for XTIDE Universal BIOS configuration menu
105g_szItemCfgBackToMain:  db  "Back to Main Menu",NULL
106g_szItemCfgIde1:        db  "Primary IDE Controller",NULL
107g_szItemCfgIde2:        db  "Secondary IDE Controller",NULL
108g_szItemCfgIde3:        db  "Tertiary IDE Controller",NULL
109g_szItemCfgIde4:        db  "Quaternary IDE Controller",NULL
110g_szItemCfgBootMenu:    db  "Boot settings",NULL
111g_szItemAutoConfigure:  db  "Auto Configure",NULL
112g_szItemCfgFullMode:    db  "Full operating mode",NULL
113g_szItemCfgStealSize:   db  "kiB to steal from RAM",NULL
114g_szItemCfgIdeCnt:      db  "IDE controllers",NULL
115g_szItemCfgIdleTimeout: db  "Power Management",NULL
116
117g_szDlgAutoConfigure:   db  "Found "
118g_bControllersDetected: db  'x'             ; Value stored directly here
119                        db  " controllers.",NULL
120g_szDlgBadBiosFound:    db  "This computer has been identified as being one of the following models:",LF,LF
121                        db  "Zenith Z-171",LF
122                        db  "Zenith Z-161",LF,LF
123                        db  "The Boot settings menu option 'Remove other hard drives' has been set to YES for this reason.",NULL
124g_szDlgCfgFullMode:     db  "Enable full operating mode?",NULL
125g_szDlgCfgStealSize:    db  "How many kiB of base memory to steal for XTIDE Universal BIOS variables (1...255)?",NULL
126g_szDlgCfgIdeCnt:       db  "How many IDE controllers to manage (1...4)?",NULL
127g_szDlgCfgIdleTimeout:  db  "Select the amount of time before idling drives should enter standby mode.",NULL
128
129g_szNfoCfgIde:          db  "IDE controller and drive configuration.",NULL
130g_szNfoCfgBootMenu:     db  "Boot configuration.",NULL
131g_szNfoAutoConfigure:   db  "Automatically Configure XTIDE Universal BIOS for this system.",NULL
132g_szNfoCfgFullMode:     db  "Full mode supports multiple controllers and has more features.",NULL
133g_szNfoCfgStealSize:    db  "How many kiB's to steal from Conventional memory for XTIDE Universal BIOS variables.",NULL
134g_szNfoCfgIdeCnt:       db  "Number of IDE controllers to manage.",NULL
135g_szNfoCfgIdleTimeout:  db  "Enable Power Management to set the harddrive(s) to spin down after idling a certain amount of time.",NULL
136
137g_szSerialMoved:        db  "A Serial Controller has been moved to the end of the Controller list."
138                        db  " No further action is required. Serial Controllers must be placed at the end of the list.",NULL
139
140g_szHelpCfgFullMode:    db  "Full mode supports up to 4 IDE controllers (8 drives). Full mode reserves a bit of RAM from the top of"
141                        db  " Conventional memory. This makes it possible to use ROM BASIC and other software that requires"
142                        db  " the interrupt vectors where XTIDE Universal BIOS parameters would be stored in Lite mode.",LF,LF
143                        db  "Lite mode supports only 2 IDE controllers (4 drives) and stores parameters to the top of the interrupt vectors"
144                        db  " (30:0h) so no Conventional memory needs to be reserved. Lite mode cannot be used if some software requires"
145                        db  " the top of interrupt vectors. Usually this is not a problem since only IBM ROM BASIC uses them.",LF,LF
146                        db  "Tandy 1000 models with 640 kiB or less memory need to use Lite mode since the top of Conventional memory gets"
147                        db  " dynamically reserved by video hardware. This happens only with Tandy integrated video controller and not when"
148                        db  " using expansion graphics cards. It is possible to use Full mode if reserving RAM for video memory + what is"
149                        db  " required for XTIDE Universal BIOS. This would mean 65 kiB but most software should work with 33 kiB reserved.",NULL
150
151g_szHelpCfgStealSize:   db  "Parameters for detected hard disks must be stored somewhere. In Full mode they are stored at the top of Conventional"
152                        db  " memory. 1 kiB is usually enough but you may have to reserve more if you want to use Full mode on a Tandy 1000.",NULL
153
154g_szHelpCfgIdleTimeout: db  "This option enables the standby timer for all harddrives handled by XTIDE Universal BIOS,"
155                        db  " allowing the drives to spin down after idling the selected amount of time."
156                        db  " Note that this does not work with old drives that lack the Power Management feature set."
157                        db  " Also note that timeouts less than 5 minutes may cause unnecessary wear on the drives and is not recommended"
158                        db  " (use for compatibility testing only).",NULL
159
160g_szMultichoiceIdleTimeout: db  "Disabled",LF
161                            db  "1 m",LF
162                            db  "2 m",LF
163                            db  "3 m",LF
164                            db  "4 m",LF
165                            db  "5 m",LF
166                            db  "6 m",LF
167                            db  "7 m",LF
168                            db  "8 m",LF
169                            db  "9 m",LF
170                            db  "10 m",LF
171                            db  "11 m",LF
172                            db  "12 m",LF
173                            db  "13 m",LF
174                            db  "14 m",LF
175                            db  "15 m",LF
176                            db  "16 m",LF
177                            db  "17 m",LF
178                            db  "18 m",LF
179                            db  "19 m",LF
180                            db  "20 m",LF
181                            db  "30 m",LF
182                            db  "1 h",LF
183                            db  "1 h 30 m",LF
184g_szIdleTimeoutChoice24:    db  "2 h",NULL
185g_szIdleTimeoutChoice23:    db  "1 h 30 m",NULL
186g_szIdleTimeoutChoice22:    db  "1 h",NULL
187g_szIdleTimeoutChoice21:    db  "30 m",NULL
188g_szIdleTimeoutChoice20:    db  "20 m",NULL
189g_szIdleTimeoutChoice19:    db  "19 m",NULL
190g_szIdleTimeoutChoice18:    db  "18 m",NULL
191g_szIdleTimeoutChoice17:    db  "17 m",NULL
192g_szIdleTimeoutChoice16:    db  "16 m",NULL
193g_szIdleTimeoutChoice15:    db  "15 m",NULL
194g_szIdleTimeoutChoice14:    db  "14 m",NULL
195g_szIdleTimeoutChoice13:    db  "13 m",NULL
196g_szIdleTimeoutChoice12:    db  "12 m",NULL
197g_szIdleTimeoutChoice11:    db  "11 m",NULL
198g_szIdleTimeoutChoice10:    db  "10 m",NULL
199g_szIdleTimeoutChoice9:     db  "9 m",NULL
200g_szIdleTimeoutChoice8:     db  "8 m",NULL
201g_szIdleTimeoutChoice7:     db  "7 m",NULL
202g_szIdleTimeoutChoice6:     db  "6 m",NULL
203g_szIdleTimeoutChoice5:     db  "5 m",NULL
204g_szIdleTimeoutChoice4:     db  "4 m",NULL
205g_szIdleTimeoutChoice3:     db  "3 m",NULL
206g_szIdleTimeoutChoice2:     db  "2 m",NULL
207g_szIdleTimeoutChoice1:     db  "1 m",NULL
208g_szIdleTimeoutChoice0:     db  "Disabled",NULL
209
210; Strings for IDE Controller menu
211g_szItemBackToCfgMenu:      db  "Back to Configuration Menu",NULL
212g_szItemIdeMaster:          db  "Master Drive",NULL
213g_szItemIdeSlave:           db  "Slave Drive",NULL
214g_szItemIdeDevice:          db  "Device type",NULL
215g_szItemIdeCmdPort:         db  "Base (cmd block) address",NULL
216g_szItemIdeCtrlPort:        db  "Control block address",NULL
217g_szItemIdeEnIRQ:           db  "Enable interrupt",NULL
218g_szItemIdeIRQ:             db  "IRQ",NULL
219g_szItemSerialCOM:          db  "COM Port",NULL
220g_szItemSerialBaud:         db  "Baud Rate",NULL
221g_szItemSerialPort:         db  "COM Port I/O address",NULL
222g_szItemIdeSerialComPort:   db  "COM port",NULL
223g_szItemIdeSerialBaudRate:  db  "Baud rate",NULL
224
225g_szDlgDevice:              db  "Select controller type.",NULL
226g_szDlgIdeCmdPort:          db  "Enter IDE command block (base port) address.",NULL
227g_szDlgIdeCtrlPort:         db  "Enter IDE control block address (usually command block + 200h).",NULL
228g_szDlgIdeEnIRQ:            db  "Enable interrupt?",NULL
229g_szDlgIdeIRQ:              db  "Enter IRQ channel (2...7 for 8-bit controllers, 2...15 for any other controller).",NULL
230g_szUnsupportedDevice:      db  "There is no support for this device type in the currently loaded BIOS."
231                            db  " You must load a BIOS built with the proper module included to be able to use this type of device.",NULL
232
233g_szNfoIdeBackToCfgMenu:    db  "Back to XTIDE Universal BIOS Configuration Menu.",NULL
234g_szNfoIdeMaster:           db  "Settings for Master Drive.",NULL
235g_szNfoIdeSlave:            db  "Settings for Slave Drive.",NULL
236g_szNfoIdeDevice:           db  "Select controller device type.",NULL
237g_szNfoIdeCmdPort:          db  "IDE Controller Command Block (base port) address or segment address for JR-IDE/ISA and SVC ADP50L.",NULL
238g_szNfoIdeCtrlPort:         db  "IDE Controller Control Block address. Usually Cmd Block + 8 for XTIDE, and Cmd Block + 200h for ATA.",NULL
239g_szNfoIdeEnIRQ:            db  "Interrupt or polling mode.",NULL
240g_szNfoIdeIRQ:              db  "IRQ channel to use.",NULL
241g_szNfoIdeSerialCOM:        db  "Select a COM port by number.",NULL
242g_szNfoIdeSerialBaud:       db  "Select the COM port's Baud Rate. The server must match this speed."
243                            db  " Note that UART clock multipliers may impact the actual speed.",NULL
244g_szNfoIdeSerialPort:       db  "Select a COM port by custom I/O port address. Any address is valid up to 3F8h, but must be on an 8-byte boundary.",NULL
245
246g_szHelpIdeCmdPort:         db  "IDE controller command block address is the usual address mentioned for IDE controllers."
247                            db  " By default the primary IDE controller uses port 1F0h and secondary controller uses port 170h."
248                            db  " XTIDE card uses port 300h by default."
249                            db  " JR-IDE/ISA and SVC ADP50L do not use ports but needs the ROM segment address set here instead.",NULL
250
251g_szHelpIdeCtrlPort:        db  "IDE controller Control Block address is normally Command Block address + 200h."
252                            db  " For XTIDE card the Control Block registers are mapped right after Command Block"
253                            db  " registers so use Command Block address + 8h for XTIDE card.",NULL
254
255g_szHelpIdeEnIRQ:           db  "IDE controller can use interrupts to signal when it is ready to transfer data."
256                            db  " This makes possible to do other tasks while waiting drive to be ready."
257                            db  " That is usually not useful in MS-DOS but using interrupts frees the bus for any DMA transfers."
258                            db  " Polling mode is used when interrupts are disabled."
259                            db  " Polling usually gives a little better access times since interrupt handling requires extra processing."
260                            db  " There can be some compatibility issues with some old drives when polling is used with Block Mode transfers.",NULL
261
262g_szHelpIdeIRQ:             db  "IRQ channel to use. All controllers managed by XTIDE Universal BIOS can use the same IRQ when MS-DOS is used."
263                            db  " Other operating systems are likely to require different interrupts for each controller.",NULL
264
265g_szHelpIdeSerialCOM:       db  "Select a serial port by COM port number. COM1 through COM4 have well established I/O port assignments,"
266                            db  ' COM5 and onward are less well established. "COMA" represents COM10, "COMB" represents COM11, and "COMC"'
267                            db  ' represents COM12. Selecting "COMx" enables the manual selection of an I/O port address.',NULL
268
269g_szHelpIdeSerialPort:      db  "Select a serial port by I/O address. Any port address is supported up to 3F8h, but must be on an 8-byte boundary."
270                            db  " If the entered value corresponds to one of the established COM port numbers, then the selection will snap"
271                            db  ' to that COM port and "COMx" must be selected again for custom I/O address entry.',NULL
272
273g_szHelpIdeSerialBaud:      db  "Supported baud rates are 2400, 4800, 9600, 19.2K, 28.8K, 38.4K, 57.6K, and 115.2K. The server must also be set to"
274                            db  " this same speed. Older UARTs may only support up to 9600 baud, but sometimes can be pushed to 38.4K. 115.2K will"
275                            db  " likely only be possible with a newer UART that includes a FIFO. Some high speed serial ports include UART clock"
276                            db  " multipliers, allowing for speeds at 230.4K (2x multiplier) and 460.8K (4x multiplier) above 115.2K. These high"
277                            db  " speeds are supported by these BIOS, even on original 4.77MHz 8088 systems. Note that UART clock multipliers are"
278                            db  " not detectable by the software and 115.2K will still be used during configuration for high speeds; but if"
279                            db  " a multiplier is used, the actual speed (including the multiplier) will need to be used by the server.",NULL
280
281g_szMultichoiceCfgDevice:   db  "16-bit ISA/VLB/PCI IDE",LF
282                            db  "32-bit VLB/PCI IDE",LF
283                            db  "16-bit ISA IDE in 8-bit mode",LF
284                            db  "XTIDE rev 1",LF
285                            db  "XTIDE rev 2 or modded rev 1",LF
286                            db  "XTIDE rev 2 (Olivetti M24)",LF
287                            db  "XT-CF PIO8",LF
288                            db  "XT-CF PIO8 (BIU offload)",LF
289                            db  "XT-CF PIO16 (BIU offload)",LF
290                            db  "XT-CF DMA (v3 only)",LF
291                            db  "JR-IDE/ISA",LF
292                            db  "SVC ADP50L",LF
293                            db  "Serial port virtual device",NULL
294
295g_szValueCfgDevice16b:                      db  "16-bit",NULL
296g_szValueCfgDevice32b:                      db  "32-bit",NULL
297g_szValueCfgDevice8b:                       db  "8-bit",NULL
298g_szValueCfgDeviceRev1:                     db  "XTIDE r1",NULL
299g_szValueCfgDeviceRev2:
300g_szValueCfgDeviceRev2Olivetti:             db  "XTIDE r2",NULL
301g_szValueCfgDeviceXTCFPio8:                 db  "XTCF PIO",NULL
302g_szValueCfgDeviceXTCFPio8WithBIUOffload:   db  "BIU 8",NULL
303g_szValueCfgDeviceXTCFPio16WithBIUOffload:  db  "BIU 16",NULL
304g_szValueCfgDeviceXTCFDMA:                  db  "XTCF DMA",NULL
305g_szValueCfgDeviceJrIdeIsa:                 db  "JR-ISA",NULL
306g_szValueCfgDeviceADP50L:                   db  "ADP50L",NULL
307g_szValueCfgDeviceSerial:                   db  "Serial",NULL
308
309g_szSerialCOMChoice:    db  "COM1 - address 3F8h",LF
310                        db  "COM2 - address 2F8h",LF
311                        db  "COM3 - address 3E8h",LF
312                        db  "COM4 - address 2E8h",LF
313                        db  "COM5 - address 2F0h",LF
314                        db  "COM6 - address 3E0h",LF
315                        db  "COM7 - address 2E0h",LF
316                        db  "COM8 - address 260h",LF
317                        db  "COM9 - address 368h",LF
318                        db  "COMA - address 268h",LF
319                        db  "COMB - address 360h",LF
320                        db  "COMC - address 270h",LF
321                        db  "COMx - Custom address",NULL
322
323g_szValueCfgCOM1:       db  "COM1",NULL
324g_szValueCfgCOM2:       db  "COM2",NULL
325g_szValueCfgCOM3:       db  "COM3",NULL
326g_szValueCfgCOM4:       db  "COM4",NULL
327g_szValueCfgCOM5:       db  "COM5",NULL
328g_szValueCfgCOM6:       db  "COM6",NULL
329g_szValueCfgCOM7:       db  "COM7",NULL
330g_szValueCfgCOM8:       db  "COM8",NULL
331g_szValueCfgCOM9:       db  "COM9",NULL
332g_szValueCfgCOMA:       db  "COMA",NULL
333g_szValueCfgCOMB:       db  "COMB",NULL
334g_szValueCfgCOMC:       db  "COMC",NULL
335g_szValueCfgCOMx:       db  "Custom",NULL
336
337g_szSerialBaudChoice:   db  "115.2K baud",LF
338                        db  "57.6K baud",LF
339                        db  "38.4K baud",LF
340                        db  "28.8K baud",LF
341                        db  "19.2K baud",LF
342                        db  "9600 baud",LF
343                        db  "4800 baud",LF
344                        db  "2400 baud",NULL
345
346g_szValueCfgBaud115_2:  db  "115.2K",NULL
347g_szValueCfgBaud57_6:   db  "57.6K",NULL
348g_szValueCfgBaud38_4:   db  "38.4K",NULL
349g_szValueCfgBaud28_8:   db  "28.8K",NULL
350g_szValueCfgBaud19_2:   db  "19.2K",NULL
351g_szValueCfgBaud9600:   db  "9600",NULL
352g_szValueCfgBaud4800:   db  "4800",NULL
353g_szValueCfgBaud2400:   db  "2400",NULL
354
355
356; Strings for DRVPARAMS menu
357g_szItemDrvBackToIde:   db  "Back to IDE Controller Menu",NULL
358g_szItemDrvBlockMode:   db  "Block Mode Transfers",NULL
359g_szItemDrvXlateMode:   db  "CHS translation method",NULL
360g_szItemDrvWriteCache:  db  "Internal Write Cache",NULL
361g_szItemDrvUserCHS:     db  "User specified CHS",NULL
362g_szItemDrvCyls:        db  "Cylinders",NULL
363g_szItemDrvHeads:       db  "Heads",NULL
364g_szItemDrvSect:        db  "Sectors per track",NULL
365g_szItemDrvUserLBA:     db  "User specified LBA",NULL
366g_szItemDrvLbaSectors:  db  "Millions of sectors",NULL
367
368g_szDlgDrvBlockMode:    db  "Enable Block Mode Transfers?",NULL
369g_szDlgDrvXlateMode:    db  "Select P-CHS to L-CHS translation method.",NULL
370g_szDlgDrvWriteCache:   db  "Select hard drive internal write cache settings.",NULL
371g_szDlgDrvUserCHS:      db  "Specify (P-)CHS parameters manually?",NULL
372g_szDlgDrvCyls:         db  "Enter number of P-CHS cylinders (1...16383).",NULL
373g_szDlgDrvHeads:        db  "Enter number of P-CHS heads (1...16).",NULL
374g_szDlgDrvSect:         db  "Enter number of sectors per track (1...63).",NULL
375g_szDlgDrvUserLBA:      db  "Limit drive capacity?",NULL
376g_szDlgDrvLbaSectors:   db  "Enter maximum capacity in millions of sectors (16...256).",NULL
377
378g_szNfoDrvBlockMode:    db  "Transfer multiple sectors per data request.",NULL
379g_szNfoDrvXlateMode:    db  "P-CHS to L-CHS translation method.",NULL
380g_szNfoDrvWriteCache:   db  "Hard Drive Internal Write Cache settings (WARNING!).",NULL
381g_szNfoDrvUserCHS:      db  "Specify (P-)CHS parameters manually instead of autodetecting them.",NULL
382g_szNfoDrvCyls:         db  "Number of user specified P-CHS cylinders.",NULL
383g_szNfoDrvHeads:        db  "Number of user specified P-CHS heads.",NULL
384g_szNfoDrvSect:         db  "Number of user specified P-CHS sectors per track.",NULL
385g_szNfoDrvUserLBA:      db  "Limit drive capacity to fix compatibility problems with Windows 9x.",NULL
386g_szNfoDrvLbaSectors:   db  "Millions of sectors (1024*1024). 1M sectors = 512 MiB. Recommended limits are 64 for Windows 95, 128 for Windows 98 and 256 for Windows ME (and 98 with updated fdisk).",NULL
387
388g_szHelpDrvBlockMode:   db  "Block Mode will speed up transfers since multiple sectors can be transferred before waiting next data request."
389                        db  " Normally Block Mode should always be kept enabled but there is at least one"
390                        db  " drive with buggy Block Mode implementation (Quantum ProDrive LPS 340A).",NULL
391
392g_szHelpDrvWriteCache:  db  "Modern Hard Drives have a large amount of internal write cache."
393                        db  " The cache will speed up writes since the drive can free the bus right after data has been written to cache."
394                        db  " The drive then starts to write the data from cache to disk by itself."
395                        db  " This can be dangerous since all unwritten data in cache is lost if power is turned off or the system is reset."
396                        db  " Modern operating systems will flush the cache when user shuts down the system."
397                        db  " DOS does not have that sort of protection so it is up to the user to make sure cache is flushed."
398                        db  " WARNING!!! Write cache should be left disabled.",NULL
399
400g_szHelpDrvUserCHS:     db  "Specify (P-)CHS parameters manually instead of autodetecting them."
401                        db  " This can be used to limit drive size for old operating systems that do not support large hard disks."
402                        db  " Some early IDE drives have buggy autodetection so they require CHS to be specified manually."
403                        db  " Limiting Cylinders will work for all drives but drives may not accept all values for Heads and Sectors per Track.",NULL
404
405g_szHelpDrvUserLBA:     db  "Limit drive size to X million sectors for EBIOS functions. This option is useful to"
406                        db  " prevent large drive compatibility problems with MS-DOS 7.x (Windows 95 and 98).",NULL
407
408g_szMultichoiseXlateMode:
409                        db  "NORMAL",LF
410                        db  "LARGE",LF
411                        db  "Assisted LBA",LF
412                        db  "Autodetect",NULL
413
414g_szValueDrvXlateNormal:db  "NORMAL",NULL
415g_szValueDrvXlateLarge: db  "LARGE",NULL
416g_szValueDrvXlateLBA:   db  "LBA",NULL
417g_szValueDrvXlateAuto:  db  "Auto",NULL
418
419g_szMultichoiseWrCache: db  "Drive Default",LF
420                        db  "Disable Write Cache",LF
421                        db  "Enable Write Cache",NULL
422
423g_szValueDrvWrCaDis:    db  "Disabled",NULL
424g_szValueDrvWrCaEn:     db  "Enabled",NULL
425
426
427; Strings for boot settings menu
428g_szItemBootTimeout:        db  "Selection timeout",NULL
429g_szItemBootDrive:          db  "Default boot drive",NULL
430g_szItemBootDispMode:       db  "Display Mode",NULL
431g_szItemColorTheme:         db  "Color Theme",NULL
432g_szItemBootFloppyDrvs:     db  "Number of Floppy Drives",NULL
433g_szItemSerialDetect:       db  "Scan for Serial Drives",NULL
434g_szItemClearBdaDriveCount: db  "Remove other hard drives",NULL
435
436g_szDlgBootTimeout:         db  "Enter Boot Menu selection timeout in BIOS timer ticks (2...1092).",NULL
437g_szDlgBootDrive:           db  "Enter default drive number (0xh for Floppy Drives, 8xh for Hard Disks).",NULL
438g_szDlgBootDispMode:        db  "Select display mode.",NULL
439g_szDlgColorTheme:          db  "Select color theme.",NULL
440g_szDlgBootFloppyDrvs:      db  "Select number of Floppy Drives in system.",NULL
441g_szDlgSerialDetect:        db  "Scan for serial drives?",NULL
442g_szDlgClearBdaDriveCount:  db  "Remove existing INT 13h hard drives during drive detection?",NULL
443
444g_szNfoBootTimeout:         db  "Menu item selection timeout in BIOS timer ticks. 1 tick = 54.9 ms.",NULL
445g_szNfoBootDrive:           db  "Default boot drive.",NULL
446g_szNfoDispMode:            db  "Display mode to set when booting.",NULL
447g_szNfoColorTheme:          db  "Color theme used by the boot menu and the hotkey bar.",NULL
448g_szNfoBootFloppyDrvs:      db  "Number of Floppy Drives in system.",NULL
449g_szNfoSerialDetect:        db  "Scans all standard COM ports for serial drives."
450                            db  " This can also be invoked by holding down ALT at the end of normal drive detection.",NULL
451g_szNfoClearBdaDriveCount:  db  "Can be used to remove duplicate hard drives.",NULL
452
453g_szHelpBootTimeout:        db  "Boot Menu selection timeout in BIOS timer ticks (1 second = 18.2 ticks)."
454                            db  " When timer goes to zero, currently selected drive will be booted automatically."
455                            db  " Timeout can be disabled by setting this to 0.",NULL
456g_szHelpBootDrive:          db  "Drive to be set selected by default when Boot Menu is displayed.",NULL
457g_szHelpColorTheme:         db  "Pick a theme from a list of several pre-defined themes to customize the colors used by the boot menu and, if"
458                            db  " available, the hotkey bar. Selecting a theme or loading a BIOS, or its settings, from file or from ROM will"
459                            db  " make XTIDECFG apply the theme to itself for easy preview. The ability to preview themes requires that"
460                            db  " XTIDECFG is running in a display mode that can display colors. In other words, you may configure the"
461                            db  " BIOS on a machine with a monochrome graphics adapter and not be able to preview the theme but the BIOS will"
462                            db  " still use the selected theme when installed in a machine with a color graphics adapter.",NULL
463g_szHelpBootFloppyDrvs:     db  "Detecting the correct number of floppy drives might fail when using a floppy controller with its own BIOS."
464                            db  " A minimum number of floppy drives can be specified to force non-detected drives to appear on boot menu.",NULL
465g_szHelpSerialDetect:       db  "Set to Yes, at the end of normal drive detection, COM ports 1-7 (in reverse order) will be scanned for a connection"
466                            db  " to a serial drive server. This option provides flexibility with the COM port and baud rate to be used,"
467                            db  " it need not be configured ahead of time, but at the expense of a slower boot process."
468                            db  " Even when this option is set to No, this functionality can still be invoked by holding down the ALT key at the end"
469                            db  " of normal drive detection. Note that if any serial drives are detected during the normal drive detection,"
470                            db  " no scan will take place (to avoid finding the same drive twice).",NULL
471g_szHelpClearBdaDriveCount: db  "Set to NO for normal operation. Set to YES to get Windows 9x protected mode drivers to work when"
472                            db  " MODULE_WIN9X_CMOS_HACK is not included (dummy drive needs to be defined in system BIOS setup). This option must"
473                            db  " also be set to YES on computers where the system BIOS does not initialize RAM properly. Zenith models Z-171 and"
474                            db  " Z-161 are known examples of such machines.",NULL
475
476g_szMultichoiceBootDispMode:    db  "Default",LF
477                                db  "40x25 Black & White",LF
478                                db  "40x25 Color",LF
479                                db  "80x25 Black & White",LF
480                                db  "80x25 Color",LF
481                                db  "80x25 Monochrome",NULL
482
483g_szValueBootDispModeDefault:   db  "Default",NULL
484g_szValueBootDispModeBW40:      db  "BW40",NULL
485g_szValueBootDispModeCO40:      db  "CO40",NULL
486g_szValueBootDispModeBW80:      db  "BW80",NULL
487g_szValueBootDispModeCO80:      db  "CO80",NULL
488g_szValueBootDispModeMono:      db  "Mono",NULL
489
490g_szMultichoiceColorTheme:      db  "Classic (default)",LF
491                                db  "Argon Blue",LF
492                                db  "Neon Red",LF
493                                db  "Phosphor Green",LF
494                                db  "Moon Surface",LF
495                                db  "Toxic Waste",NULL
496g_szValueColorTheme0:           db  "Classic",NULL
497g_szValueColorTheme1:           db  "Argon",NULL
498g_szValueColorTheme2:           db  "Neon",NULL
499g_szValueColorTheme3:           db  "Phosphor",NULL
500g_szValueColorTheme4:           db  "Moon",NULL
501g_szValueColorTheme5:           db  "Toxic",NULL
502
503g_szMultichoiceBootFloppyDrvs:  db  "Autodetect",LF
504                                db  "1",LF
505                                db  "2",LF
506                                db  "3",LF
507g_szValueBootFloppyDrvs4:       db  "4",NULL
508g_szValueBootFloppyDrvs3:       db  "3",NULL
509g_szValueBootFloppyDrvs2:       db  "2",NULL
510g_szValueBootFloppyDrvs1:       db  "1",NULL
511g_szValueBootFloppyDrvsAuto:    db  "Auto",NULL
512
513
514; Strings for Flash menu
515g_szItemFlashStart:     db  "Start flashing",NULL
516g_szItemFlashEepromType:db  "EEPROM type",NULL
517g_szItemFlashSDP:       db  "SDP command",NULL
518g_szItemFlashAddr:      db  "EEPROM address",NULL
519g_szItemFlashPageSize:  db  "Page size",NULL
520g_szItemFlashChecksum:  db  "Generate checksum byte",NULL
521
522g_szDlgFlashEepromType: db  "Select EEPROM type.",NULL
523g_szDlgFlashSDP:        db  "Select Software Data Protection command.",NULL
524g_szDlgFlashAddr:       db  "Enter segment address where EEPROM is located.",NULL
525g_szDlgFlashPageSize:   db  "Select write page size.",NULL
526g_szDlgFlashChecksum:   db  "Generate checksum byte to the end of BIOS image?",NULL
527
528g_szNfoFlashEepromType: db  "EEPROM type.",NULL
529g_szNfoFlashStart:      db  "Writes BIOS to EEPROM.",NULL
530g_szNfoFlashSDP:        db  "Software Data Protection command.",NULL
531g_szNfoFlashAddr:       db  "Address (segment) where EEPROM is located.",NULL
532g_szNfoFlashPageSize:   db  "Number of bytes to write before delay.",NULL
533g_szNfoFlashChecksum:   db  "Generate checksum byte to the end of BIOS image.",NULL
534
535g_szHelpFlashSDP:       db  "Software Data Protection Command:",LF
536                        db  "None    = Do not use Software Data Protection. Meant for EEPROMs that do not support SDP.",LF,LF
537                        db  "Enable  = Write protects the EEPROM after flashing."
538                        db  " Software Data Protection should always be enabled if EEPROM supports it.",LF,LF
539                        db  "Disable = Disables Software Data Protection after flashing.",NULL
540
541g_szHelpFlashPageSize:  db  "Larger page size will improve write performance but not all EEPROMs support large pages or page writing at all."
542                        db  " Byte writing mode will be used when page size is set to 1. Byte writing mode is supported by all EEPROMs."
543                        db  " Large pages cannot be flashed with slow CPUs.",NULL
544
545g_szHelpFlashChecksum:  db  "PC BIOSes require a checksum byte at the end of expansion card BIOS ROMs."
546                        db  " You might not want to generate checksum byte when flashing some other images than XTIDE Universal BIOS.",NULL
547
548g_szMultichoiceEepromType:
549                        db  "2816 (2 kiB)",LF
550                        db  "2864 (8 kiB)",LF
551                        db  "2864 mod (8 kiB)",LF
552                        db  "28256 (32 kiB)",LF
553                        db  "28512 (64 kiB)",NULL
554g_szValueFlash2816:     db  "2816",NULL
555g_szValueFlash2864:     db  "2864",NULL
556g_szValueFlash2864Mod:  db  "2864mod",NULL
557g_szValueFlash28256:    db  "28256",NULL
558g_szValueFlash28512:    db  "28512",NULL
559
560g_szMultichoiceSdpCommand:
561                        db  "None",LF
562                        db  "Enable",LF
563g_szValueFlashDisable:  db  "Disable",NULL
564g_szValueFlashEnable:   db  "Enable",NULL
565g_szValueFlashNone:     db  "None",NULL
566
567g_szMultichoicePageSize:
568                        db  "1 byte",LF
569                        db  "2 bytes",LF
570                        db  "4 bytes",LF
571                        db  "8 bytes",LF
572                        db  "16 bytes",LF
573                        db  "32 bytes",LF
574g_szValueFlash64bytes:  db  "64 bytes",NULL
575g_szValueFlash32bytes:  db  "32 bytes",NULL
576g_szValueFlash16bytes:  db  "16 bytes",NULL
577g_szValueFlash8bytes:   db  "8 bytes",NULL
578g_szValueFlash4bytes:   db  "4 bytes",NULL
579g_szValueFlash2bytes:   db  "2 bytes",NULL
580g_szValueFlash1byte:    db  "1 byte",NULL
581
582g_szSelectionTimeout:   db  DOUBLE_BOTTOM_LEFT_CORNER,DOUBLE_LEFT_HORIZONTAL_TO_SINGLE_VERTICAL,"%ASelection in %2u s",NULL
583g_szDashForZero:        db  "- ",NULL
584g_szValueUnknownError:  db  "Error!",NULL
585
Note: See TracBrowser for help on using the repository browser.