source: xtideuniversalbios/trunk/XTIDE_Universal_BIOS_Configurator_v2/Src/Strings.asm @ 536

Last change on this file since 536 was 536, checked in by krille_n_@…, 11 years ago

Changes:

  • Added support for the Silicon Valley Computer ADP50L controller (and possibly other IDE controllers from SVC using memory mapped I/O). Please note that this has not been tested in any way since I don't have any of these cards myself (make backups before trying this on drives with important data). Also, *if* it works, make sure it works reliably (stress test the disk system). Some things you should know: 1) Autodetection for this controller has not been added to XTIDECFG, you need to manually select the "SVC ADP50L" controller (and possibly change the BIOS segment address if not using the default of C800h). 2) The memory mapped I/O window is inside the ROM address space of the controller. The XTIDE Universal BIOS currently do not support this so that means you need to use another ROM (for example, an XTIDE or XTCF card or the BOOT ROM of a NIC). This presents another problem, the original ADP50L BIOS needs to be disabled somehow to avoid conflicts. Either pull the ROM chip or disable the BIOS by removing jumper J3. Note, I have no idea if any of this will actually work. It's basically a shot in the dark.
File size: 28.2 KB
Line 
1; Project name  :   XTIDE Universal BIOS Configurator v2
2; Description   :   All strings.
3
4;
5; XTIDE Universal BIOS and Associated Tools
6; Copyright (C) 2009-2010 by Tomi Tilli, 2011-2013 by XTIDE Universal BIOS Team.
7;
8; This program is free software; you can redistribute it and/or modify
9; it under the terms of the GNU General Public License as published by
10; the Free Software Foundation; either version 2 of the License, or
11; (at your option) any later version.
12;
13; This program is distributed in the hope that it will be useful,
14; but WITHOUT ANY WARRANTY; without even the implied warranty of
15; MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
16; GNU General Public License for more details.
17; Visit http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
18;
19
20; Section containing initialized data
21SECTION .data
22
23; Menu title
24g_szProgramTitle:                   db  "Configuration and Flashing program for XTIDE Universal BIOS v2.0.0.",LF,CR,NULL
25g_szXtideUniversalBiosSignature:    db  "XTIDE203",NULL
26g_szBiosIsNotLoaded:                db  "BIOS is not loaded!",NULL
27g_szEEPROM:                         db  "EEPROM",NULL
28g_szSourceAndTypeSeparator:         db  " : ",NULL
29g_szUnidentified:                   db  "Unidentified",NULL
30g_szUnsaved:                        db  " ",SINGLE_LEFT_HORIZONTAL_TO_VERTICAL,"Unsaved",SINGLE_RIGHT_HORIZONTAL_TO_VERTICAL,NULL
31
32; Item formatting
33g_szFormatItemWithoutValue:         db  "%c%s",NULL
34g_szFormatItemNameWithValue:        db  "%25s%-10S",NULL
35
36
37g_szNo:                             db  "No",NULL
38g_szMultichoiceBooleanFlag:         db  "No",LF
39g_szYes:                            db  "Yes",NULL
40
41; Exit messages
42g_szDlgExitToDos:       db  "Exit to DOS?",NULL
43g_szDlgSaveChanges:     db  "Do you want to save changes to XTIDE Universal BIOS image file?",NULL
44
45
46; Generic dialog strings
47g_szNotificationDialog: db  "Notification.",NULL
48g_szErrorDialog:        db  "Error!",NULL
49g_szGenericDialogInfo:  db  "Press ENTER or ESC to close dialog.",NULL
50
51; Flashing related strings
52g_szFlashTitle:         db  "Flashing EEPROM, please wait.",NULL
53g_szErrEepromTooSmall:  db  "Image is too large for selected EEPROM type!",NULL
54g_szErrEepromPolling:   db  "Timeout when polling EEPROM.",LF
55                        db  "EEPROM was not flashed properly!",NULL
56g_szErrEepromVerify:    db  "EEPROM did not return the same byte that was written.",LF
57                        db  "EEPROM was not flashed properly!",NULL
58g_szPCFlashSuccessful:  db  "EEPROM was written successfully.",LF
59                        db  "Press any key to reboot.",NULL
60g_szForeignFlash:       db  "EEPROM was written successfully.",NULL
61
62
63; Strings for main menu
64g_szItemMainExitToDOS:  db  "Exit to DOS",NULL
65g_szItemMainLoadFile:   db  "Load BIOS from file",NULL
66g_szItemMainLoadROM:    db  "Load BIOS from EEPROM",NULL
67g_szItemMainLoadStngs:  db  "Load old settings from EEPROM",NULL
68g_szItemMainConfigure:  db  "Configure XTIDE Universal BIOS",NULL
69g_szItemMainFlash:      db  "Flash EEPROM",NULL
70g_szItemMainSave:       db  "Save BIOS back to original file",NULL
71g_szItemMainLicense:    db  "Copyright and License Information",NULL
72g_szItemMainHomePage:   db  "Web Links",NULL
73
74g_szDlgMainLoadROM:     db  "Successfully loaded XTIDE Universal BIOS from EEPROM.",NULL
75g_szDlgMainLoadStngs:   db  "Successfully loaded settings from EEPROM.",NULL
76g_szDlgMainLoadFile:    db  "Successfully loaded file for flashing.",NULL
77g_szDlgMainSaveFile:    db  "Successfully saved XTIDE Universal BIOS to file.",NULL
78g_szDlgMainFileTooBig:  db  "Selected file is too big to be loaded for flashing!",NULL
79g_szDlgMainLoadErr:     db  "Failed to load file!",NULL
80g_szDlgMainSaveErr:     db  "Failed to save file!",NULL
81g_szDlgFileTitle:       db  "Select file to be flashed.",NULL
82g_szDlgFileFilter:      db  "*.*",NULL
83
84g_szNfoMainExitToDOS:   db  "Quits XTIDE Universal BIOS Configurator.",NULL
85g_szNfoMainLoadFile:    db  "Load BIOS file to be configured or flashed.",NULL
86g_szNfoMainLoadROM:     db  "Load BIOS from EEPROM to be reconfigured.",NULL
87g_szNfoMainLoadStngs:   db  "Load old XTIDE Universal BIOS settings from EEPROM.",NULL
88g_szNfoMainConfigure:   db  "Configure XTIDE Universal BIOS settings.",NULL
89g_szNfoMainFlash:       db  "Flash loaded BIOS image to EEPROM.",NULL
90g_szNfoMainSave:        db  "Save BIOS changes back to original file from which it was loaded.",NULL
91g_szNfoMainLicense:     db  "XTIDE Universal BIOS and XTIDECFG Copyright (C) 2009-2010 by Tomi Tilli, 2011-2013 by XTIDE Universal BIOS Team."
92                        db  " Released under GNU GPL v2, with ABSOLUTELY NO WARRANTY. Press ENTER for more details...",NULL
93g_szNfoMainHomePage:    db  "Visit http://code.google.com/p/ xtideuniversalbios (home page) and http://vintage-computer.com/ vcforum (support)",NULL
94
95g_szHelpMainLicense:    db  "XTIDE Universal BIOS and XTIDECFG Configuration program are Copyright 2009-2010 by Tomi Tilli,"
96                        db  " 2011-2013 by XTIDE Universal BIOS Team. Released under GNU GPL v2. This software comes with ABSOLUTELY NO WARRANTY."
97                        db  " This is free software, and you are welcome to redistribute it under certain conditions."
98                        db  " See the LICENSE.TXT file that was included with this distribution,"
99                        db  " visit http://www.gnu.org/licenses/ gpl-2.0.html, or visit http://code.coogle.com/p/ xtideuniversalbios.",NULL
100
101; Strings for XTIDE Universal BIOS configuration menu
102g_szItemCfgBackToMain:  db  "Back to Main Menu",NULL
103g_szItemCfgIde1:        db  "Primary IDE Controller",NULL
104g_szItemCfgIde2:        db  "Secondary IDE Controller",NULL
105g_szItemCfgIde3:        db  "Tertiary IDE Controller",NULL
106g_szItemCfgIde4:        db  "Quaternary IDE Controller",NULL
107g_szItemCfgBootMenu:    db  "Boot settings",NULL
108g_szItemAutoConfigure:  db  "Auto Configure",NULL
109g_szItemCfgFullMode:    db  "Full operating mode",NULL
110g_szItemCfgStealSize:   db  "kiB to steal from RAM",NULL
111g_szItemCfgIdeCnt:      db  "IDE controllers",NULL
112g_szItemCfgIdleTimeout: db  "Power Management",NULL
113
114g_szDlgAutoConfigure:   db  "Found "
115g_bControllersDetected: db  'x'             ; Value stored directly here
116                        db  " controllers.",NULL
117g_szDlgCfgFullMode:     db  "Enable full operating mode?",NULL
118g_szDlgCfgStealSize:    db  "How many kiB of base memory to steal for XTIDE Universal BIOS variables (1...255)?",NULL
119g_szDlgCfgIdeCnt:       db  "How many IDE controllers to manage (1...4)?",NULL
120g_szDlgCfgIdleTimeout:  db  "Select the amount of time before idling drives should enter standby mode.",NULL
121
122g_szNfoCfgIde:          db  "IDE controller and drive configuration.",NULL
123g_szNfoCfgBootMenu:     db  "Boot configuration.",NULL
124g_szNfoAutoConfigure:   db  "Automatically Configure XTIDE Universal BIOS for this system.",NULL
125g_szNfoCfgFullMode:     db  "Full mode supports multiple controllers and has more features.",NULL
126g_szNfoCfgStealSize:    db  "How many kiB's to steal from Conventional memory for XTIDE Universal BIOS variables.",NULL
127g_szNfoCfgIdeCnt:       db  "Number of IDE controllers to manage.",NULL
128g_szNfoCfgIdleTimeout:  db  "Enable Power Management to set the harddrive(s) to spin down after idling a certain amount of time.",NULL
129
130g_szSerialMoved:        db  "A Serial Controller has been moved to the end of the Controller list."
131                        db  " No further action is required. Serial Controllers must be placed at the end of the list.",NULL
132
133g_szHelpCfgFullMode:    db  "Full mode supports up to 4 IDE controllers (8 drives). Full mode reserves a bit of RAM from the top of"
134                        db  " Conventional memory. This makes it possible to use ROM BASIC and other software that requires"
135                        db  " the interrupt vectors where XTIDE Universal BIOS parameters would be stored in Lite mode.",LF,LF
136                        db  "Lite mode supports only one IDE controller (2 drives) and stores parameters to the top of the interrupt vectors"
137                        db  " (30:0h) so no Conventional memory needs to be reserved. Lite mode cannot be used if some software requires"
138                        db  " the top of interrupt vectors. Usually this is not a problem since only IBM ROM BASIC uses them.",LF,LF
139                        db  "Tandy 1000 models with 640 kiB or less memory need to use Lite mode since the top of Conventional memory gets"
140                        db  " dynamically reserved by video hardware. This happens only with Tandy integrated video controller and not when"
141                        db  " using expansion graphics cards. It is possible to use Full mode if reserving RAM for video memory + what is"
142                        db  " required for XTIDE Universal BIOS. This would mean 65 kiB but most software should work with 33 kiB reserved.",NULL
143
144g_szHelpCfgStealSize:   db  "Parameters for detected hard disks must be stored somewhere. In Full mode they are stored at the top of Conventional"
145                        db  " memory. 1 kiB is usually enough but you may have to reserve more if you want to use Full mode on a Tandy 1000.",NULL
146
147g_szHelpCfgIdleTimeout: db  "This option enables the standby timer for all harddrives handled by XTIDE Universal BIOS,"
148                        db  " allowing the drives to spin down after idling the selected amount of time."
149                        db  " Note that this does not work with old drives that lack the Power Management feature set."
150                        db  " Also note that timeouts less than 5 minutes may cause unnecessary wear on the drives and is not recommended"
151                        db  " (use for compatibility testing only).",NULL
152
153g_szMultichoiceIdleTimeout: db  "Disabled",LF
154                            db  "1 m",LF
155                            db  "2 m",LF
156                            db  "3 m",LF
157                            db  "4 m",LF
158                            db  "5 m",LF
159                            db  "6 m",LF
160                            db  "7 m",LF
161                            db  "8 m",LF
162                            db  "9 m",LF
163                            db  "10 m",LF
164                            db  "11 m",LF
165                            db  "12 m",LF
166                            db  "13 m",LF
167                            db  "14 m",LF
168                            db  "15 m",LF
169                            db  "16 m",LF
170                            db  "17 m",LF
171                            db  "18 m",LF
172                            db  "19 m",LF
173                            db  "20 m",LF
174                            db  "30 m",LF
175                            db  "1 h",LF
176                            db  "1 h 30 m",LF
177g_szIdleTimeoutChoice24:    db  "2 h",NULL
178g_szIdleTimeoutChoice23:    db  "1 h 30 m",NULL
179g_szIdleTimeoutChoice22:    db  "1 h",NULL
180g_szIdleTimeoutChoice21:    db  "30 m",NULL
181g_szIdleTimeoutChoice20:    db  "20 m",NULL
182g_szIdleTimeoutChoice19:    db  "19 m",NULL
183g_szIdleTimeoutChoice18:    db  "18 m",NULL
184g_szIdleTimeoutChoice17:    db  "17 m",NULL
185g_szIdleTimeoutChoice16:    db  "16 m",NULL
186g_szIdleTimeoutChoice15:    db  "15 m",NULL
187g_szIdleTimeoutChoice14:    db  "14 m",NULL
188g_szIdleTimeoutChoice13:    db  "13 m",NULL
189g_szIdleTimeoutChoice12:    db  "12 m",NULL
190g_szIdleTimeoutChoice11:    db  "11 m",NULL
191g_szIdleTimeoutChoice10:    db  "10 m",NULL
192g_szIdleTimeoutChoice9:     db  "9 m",NULL
193g_szIdleTimeoutChoice8:     db  "8 m",NULL
194g_szIdleTimeoutChoice7:     db  "7 m",NULL
195g_szIdleTimeoutChoice6:     db  "6 m",NULL
196g_szIdleTimeoutChoice5:     db  "5 m",NULL
197g_szIdleTimeoutChoice4:     db  "4 m",NULL
198g_szIdleTimeoutChoice3:     db  "3 m",NULL
199g_szIdleTimeoutChoice2:     db  "2 m",NULL
200g_szIdleTimeoutChoice1:     db  "1 m",NULL
201g_szIdleTimeoutChoice0:     db  "Disabled",NULL
202
203; Strings for IDE Controller menu
204g_szItemBackToCfgMenu:      db  "Back to Configuration Menu",NULL
205g_szItemIdeMaster:          db  "Master Drive",NULL
206g_szItemIdeSlave:           db  "Slave Drive",NULL
207g_szItemIdeDevice:          db  "Device type",NULL
208g_szItemIdeCmdPort:         db  "Base (cmd block) address",NULL
209g_szItemIdeCtrlPort:        db  "Control block address",NULL
210g_szItemIdeEnIRQ:           db  "Enable interrupt",NULL
211g_szItemIdeIRQ:             db  "IRQ",NULL
212g_szItemIdeXTCFwindow:      db  "XT-CF v2 Sector Window",NULL
213g_szItemSerialCOM:          db  "COM Port",NULL
214g_szItemSerialBaud:         db  "Baud Rate",NULL
215g_szItemSerialPort:         db  "COM Port I/O address",NULL
216g_szItemIdeSerialComPort:   db  "COM port",NULL
217g_szItemIdeSerialBaudRate:  db  "Baud rate",NULL
218
219g_szDlgDevice:              db  "Select controller type.",NULL
220g_szDlgIdeCmdPort:          db  "Enter IDE command block (base port) address.",NULL
221g_szDlgIdeCtrlPort:         db  "Enter IDE control block address (usually command block + 200h).",NULL
222g_szDlgIdeEnIRQ:            db  "Enable interrupt?",NULL
223g_szDlgIdeIRQ:              db  "Enter IRQ channel (2...7 for 8-bit controllers, 2...15 for any other controller).",NULL
224g_szDlgIdeXTCFwindow:       db  "XT-CF v2 Sector Window segment (A000h...E800h).",NULL
225
226g_szNfoIdeBackToCfgMenu:    db  "Back to XTIDE Universal BIOS Configuration Menu.",NULL
227g_szNfoIdeMaster:           db  "Settings for Master Drive.",NULL
228g_szNfoIdeSlave:            db  "Settings for Slave Drive.",NULL
229g_szNfoIdeDevice:           db  "Select controller device type.",NULL
230g_szNfoIdeCmdPort:          db  "IDE Controller Command Block (base port) address or segment address for JR-IDE/ISA and SVC ADP50L.",NULL
231g_szNfoIdeCtrlPort:         db  "IDE Controller Control Block address. Usually Cmd Block + 8 for XTIDE, and Cmd Block + 200h for ATA.",NULL
232g_szNfoIdeEnIRQ:            db  "Interrupt or polling mode.",NULL
233g_szNfoIdeIRQ:              db  "IRQ channel to use.",NULL
234g_szNfoIdeXTCFwindow:       db  "Segment Address for XT-CF v2 4 kiB Sector Access Window.",NULL
235g_szNfoIdeSerialCOM:        db  "Select a COM port by number.",NULL
236g_szNfoIdeSerialBaud:       db  "Select the COM port's Baud Rate. The server must match this speed."
237                            db  " Note that UART clock multipliers may impact the actual speed.",NULL
238g_szNfoIdeSerialPort:       db  "Select a COM port by custom I/O port address. Any address is valid up to 3F8h, but must be on an 8-byte boundary.",NULL
239
240g_szHelpIdeCmdPort:         db  "IDE controller command block address is the usual address mentioned for IDE controllers."
241                            db  " By default the primary IDE controller uses port 1F0h and secondary controller uses port 170h."
242                            db  " XTIDE card uses port 300h by default."
243                            db  " JR-IDE/ISA and SVC ADP50L do not use ports but needs the ROM segment address set here instead.",NULL
244
245g_szHelpIdeCtrlPort:        db  "IDE controller Control Block address is normally Command Block address + 200h."
246                            db  " For XTIDE card the Control Block registers are mapped right after Command Block"
247                            db  " registers so use Command Block address + 8h for XTIDE card.",NULL
248
249g_szHelpIdeEnIRQ:           db  "IDE controller can use interrupts to signal when it is ready to transfer data."
250                            db  " This makes possible to do other tasks while waiting drive to be ready."
251                            db  " That is usually not useful in MS-DOS but using interrupts frees the bus for any DMA transfers."
252                            db  " Polling mode is used when interrupts are disabled."
253                            db  " Polling usually gives a little better access times since interrupt handling requires extra processing."
254                            db  " There can be some compatibility issues with some old drives when polling is used with Block Mode transfers.",NULL
255
256g_szHelpIdeIRQ:             db  "IRQ channel to use. All controllers managed by XTIDE Universal BIOS can use the same IRQ when MS-DOS is used."
257                            db  " Other operating systems are likely to require different interrupts for each controller.",NULL
258
259g_szHelpIdeSerialCOM:       db  "Select a serial port by COM port number. COM1 through COM4 have well established I/O port assignments,"
260                            db  ' COM5 and onward are less well established. "COMA" represents COM10, "COMB" represents COM11, and "COMC"'
261                            db  ' represents COM12. Selecting "COMx" enables the manual selection of an I/O port address.',NULL
262
263g_szHelpIdeSerialPort:      db  "Select a serial port by I/O address. Any port address is supported up to 3F8h, but must be on an 8-byte boundary."
264                            db  " If the entered value corresponds to one of the established COM port numbers, then the selection will snap"
265                            db  ' to that COM port and "COMx" must be selected again for custom I/O address entry.',NULL
266
267g_szHelpIdeSerialBaud:      db  "Supported baud rates are 2400, 4800, 9600, 19.2K, 28.8K, 38.4K, 57.6K, and 115.2K. The server must also be set to"
268                            db  " this same speed. Older UARTs may only support up to 9600 baud, but sometimes can be pushed to 38.4K. 115.2K will"
269                            db  " likely only be possible with a newer UART that includes a FIFO. Some high speed serial ports include UART clock"
270                            db  " multipliers, allowing for speeds at 230.4K (2x multiplier) and 460.8K (4x multiplier) above 115.2K. These high"
271                            db  " speeds are supported by these BIOS, even on original 4.77MHz 8088 systems. Note that UART clock multipliers are"
272                            db  " not detectable by the software and 115.2K will still be used during configuration for high speeds; but if"
273                            db  " a multiplier is used, the actual speed (including the multiplier) will need to be used by the server.",NULL
274
275g_szMultichoiceCfgDevice:   db  "16-bit ISA/VLB/PCI IDE",LF
276                            db  "32-bit VLB/PCI IDE",LF
277                            db  "16-bit ISA IDE in 8-bit mode",LF
278                            db  "XTIDE rev 1",LF
279                            db  "XTIDE rev 2 or modded rev 1",LF
280                            db  "XT-CF v2/v3/Lite in PIO mode",LF
281                            db  "XT-CF v2 in DMA mode",LF
282                            db  "XT-CF v2 in memory mode",LF
283                            db  "JR-IDE/ISA",LF
284                            db  "SVC ADP50L",LF
285                            db  "Serial port virtual device",NULL
286
287g_szValueCfgDevice16b:      db  "16-bit",NULL
288g_szValueCfgDevice32b:      db  "32-bit",NULL
289g_szValueCfgDevice8b:       db  "8-bit",NULL
290g_szValueCfgDeviceRev1:     db  "XTIDE r1",NULL
291g_szValueCfgDeviceRev2:     db  "XTIDE r2",NULL
292g_szValueCfgDevicePioXTCF:  db  "XTCF PIO",NULL
293g_szValueCfgDeviceDmaXTCF:  db  "XTCF DMA",NULL
294g_szValueCfgDeviceMemXTCF:  db  "XTCF MEM",NULL
295g_szValueCfgDeviceJrIdeIsa: db  "JR-ISA",NULL
296g_szValueCfgDeviceADP50L:   db  "ADP50L",NULL
297g_szValueCfgDeviceSerial:   db  "Serial",NULL
298
299g_szSerialCOMChoice:    db  "COM1 - address 3F8h",LF
300                        db  "COM2 - address 2F8h",LF
301                        db  "COM3 - address 3E8h",LF
302                        db  "COM4 - address 2E8h",LF
303                        db  "COM5 - address 2F0h",LF
304                        db  "COM6 - address 3E0h",LF
305                        db  "COM7 - address 2E0h",LF
306                        db  "COM8 - address 260h",LF
307                        db  "COM9 - address 368h",LF
308                        db  "COMA - address 268h",LF
309                        db  "COMB - address 360h",LF
310                        db  "COMC - address 270h",LF
311                        db  "COMx - Custom address",NULL
312
313g_szValueCfgCOM1:       db  "COM1",NULL
314g_szValueCfgCOM2:       db  "COM2",NULL
315g_szValueCfgCOM3:       db  "COM3",NULL
316g_szValueCfgCOM4:       db  "COM4",NULL
317g_szValueCfgCOM5:       db  "COM5",NULL
318g_szValueCfgCOM6:       db  "COM6",NULL
319g_szValueCfgCOM7:       db  "COM7",NULL
320g_szValueCfgCOM8:       db  "COM8",NULL
321g_szValueCfgCOM9:       db  "COM9",NULL
322g_szValueCfgCOMA:       db  "COMA",NULL
323g_szValueCfgCOMB:       db  "COMB",NULL
324g_szValueCfgCOMC:       db  "COMC",NULL
325g_szValueCfgCOMx:       db  "Custom",NULL
326
327g_szSerialBaudChoice:   db  "115.2K baud",LF
328                        db  "57.6K baud",LF
329                        db  "38.4K baud",LF
330                        db  "28.8K baud",LF
331                        db  "19.2K baud",LF
332                        db  "9600 baud",LF
333                        db  "4800 baud",LF
334                        db  "2400 baud",NULL
335
336g_szValueCfgBaud115_2:  db  "115.2K",NULL
337g_szValueCfgBaud57_6:   db  "57.6K",NULL
338g_szValueCfgBaud38_4:   db  "38.4K",NULL
339g_szValueCfgBaud28_8:   db  "28.8K",NULL
340g_szValueCfgBaud19_2:   db  "19.2K",NULL
341g_szValueCfgBaud9600:   db  "9600",NULL
342g_szValueCfgBaud4800:   db  "4800",NULL
343g_szValueCfgBaud2400:   db  "2400",NULL
344
345
346; Strings for DRVPARAMS menu
347g_szItemDrvBackToIde:   db  "Back to IDE Controller Menu",NULL
348g_szItemDrvBlockMode:   db  "Block Mode Transfers",NULL
349g_szItemDrvXlateMode:   db  "CHS translation method",NULL
350g_szItemDrvWriteCache:  db  "Internal Write Cache",NULL
351g_szItemDrvUserCHS:     db  "User specified CHS",NULL
352g_szItemDrvCyls:        db  "Cylinders",NULL
353g_szItemDrvHeads:       db  "Heads",NULL
354g_szItemDrvSect:        db  "Sectors per track",NULL
355g_szItemDrvUserLBA:     db  "User specified LBA",NULL
356g_szItemDrvLbaSectors:  db  "Millions of sectors",NULL
357
358g_szDlgDrvBlockMode:    db  "Enable Block Mode Transfers?",NULL
359g_szDlgDrvXlateMode:    db  "Select P-CHS to L-CHS translation method.",NULL
360g_szDlgDrvWriteCache:   db  "Select hard drive internal write cache settings.",NULL
361g_szDlgDrvUserCHS:      db  "Specify (P-)CHS parameters manually?",NULL
362g_szDlgDrvCyls:         db  "Enter number of P-CHS cylinders (1...16383).",NULL
363g_szDlgDrvHeads:        db  "Enter number of P-CHS heads (1...16).",NULL
364g_szDlgDrvSect:         db  "Enter number of sectors per track (1...63).",NULL
365g_szDlgDrvUserLBA:      db  "Limit drive capacity?",NULL
366g_szDlgDrvLbaSectors:   db  "Enter maximum capacity in millions of sectors (16...256).",NULL
367
368g_szNfoDrvBlockMode:    db  "Transfer multiple sectors per data request.",NULL
369g_szNfoDrvXlateMode:    db  "P-CHS to L-CHS translation method.",NULL
370g_szNfoDrvWriteCache:   db  "Hard Drive Internal Write Cache settings (WARNING!).",NULL
371g_szNfoDrvUserCHS:      db  "Specify (P-)CHS parameters manually instead of autodetecting them.",NULL
372g_szNfoDrvCyls:         db  "Number of user specified P-CHS cylinders.",NULL
373g_szNfoDrvHeads:        db  "Number of user specified P-CHS heads.",NULL
374g_szNfoDrvSect:         db  "Number of user specified P-CHS sectors per track.",NULL
375g_szNfoDrvUserLBA:      db  "Limit drive capacity to X million sectors.",NULL
376g_szNfoDrvLbaSectors:   db  "Millions of sectors (1024*1024). 1M sectors = 512 MiB.",NULL
377
378g_szHelpDrvBlockMode:   db  "Block Mode will speed up transfers since multiple sectors can be transferred before waiting next data request."
379                        db  " Normally Block Mode should always be kept enabled but there is at"
380                        db  " least one drive with buggy Block Mode implementation.",NULL
381
382g_szHelpDrvWriteCache:  db  "Modern Hard Drives have large internal write cache."
383                        db  " The cache will speed up writes since the drive can free the bus right after data has been written in cache."
384                        db  " The drive then starts to write the data from cache by itself."
385                        db  " That can be dangerous since all unwritten data in cache is lost if power is turned off or the system is reset."
386                        db  " Modern operating systems will flush the cache when user shuts down the system."
387                        db  " DOS does not have that sort of protection so it is up to the user to make sure cache is flushed."
388                        db  " WARNING!!! Write cache should be left disabled.",NULL
389
390g_szHelpDrvUserCHS:     db  "Specify (P-)CHS parameters manually instead of autodetecting them."
391                        db  " This can be used to limit drive size for old operating systems that do not support large hard disks."
392                        db  " Some early IDE drives have buggy autodetection so they require CHS to be specified manually."
393                        db  " Limiting Cylinders will work for all drives but drives may not accept all values for Heads and Sectors per Track.",NULL
394
395g_szHelpDrvUserLBA:     db  "Limit drive size to X million sectors for EBIOS functions. This option is useful to"
396                        db  " prevent large drive compatibility problems with MS-DOS 7.x (Windows 95 and 98).",NULL
397
398g_szMultichoiseXlateMode:
399                        db  "NORMAL",LF
400                        db  "LARGE",LF
401                        db  "Assisted LBA",LF
402                        db  "Autodetect",NULL
403
404g_szValueDrvXlateNormal:db  "NORMAL",NULL
405g_szValueDrvXlateLarge: db  "LARGE",NULL
406g_szValueDrvXlateLBA:   db  "LBA",NULL
407g_szValueDrvXlateAuto:  db  "Auto",NULL
408
409g_szMultichoiseWrCache: db  "Drive Default",LF
410                        db  "Disable Write Cache",LF
411                        db  "Enable Write Cache",NULL
412
413g_szValueDrvWrCaDis:    db  "Disabled",NULL
414g_szValueDrvWrCaEn:     db  "Enabled",NULL
415
416
417; Strings for boot settings menu
418g_szItemBootTimeout:    db  "Selection timeout",NULL
419g_szItemBootDrive:      db  "Default boot drive",NULL
420g_szItemBootDispMode:   db  "Display Mode",NULL
421g_szItemBootFloppyDrvs: db  "Number of Floppy Drives",NULL
422g_szItemSerialDetect:   db  "Scan for Serial Drives",NULL
423
424g_szDlgBootTimeout:     db  "Enter Boot Menu selection timeout in BIOS timer ticks (2...1092).",NULL
425g_szDlgBootDrive:       db  "Enter default drive number (0xh for Floppy Drives, 8xh for Hard Disks).",NULL
426g_szDlgBootDispMode:    db  "Select display mode.",NULL
427g_szDlgBootFloppyDrvs:  db  "Select number of Floppy Drives in system.",NULL
428g_szDlgSerialDetect:    db  "Scan for serial drives?",NULL
429
430g_szNfoBootTimeout:     db  "Menu item selection timeout in BIOS timer ticks. 1 tick = 54.9 ms.",NULL
431g_szNfoBootDrive:       db  "Default boot drive.",NULL
432g_szNfoDispMode:        db  "Display mode to set when booting.",NULL
433g_szNfoBootFloppyDrvs:  db  "Number of Floppy Drives in system.",NULL
434g_szNfoSerialDetect:    db  "Scans all standard COM ports for serial drives."
435                        db  " This can also be invoked by holding down ALT at the end of normal drive detection.",NULL
436
437g_szHelpBootTimeout:    db  "Boot Menu selection timeout in BIOS timer ticks (1 second = 18.2 ticks)."
438                        db  " When timer goes to zero, currently selected drive will be booted automatically."
439                        db  " Timeout can be disabled by setting this to 0.",NULL
440
441g_szHelpBootDrive:      db  "Drive to be set selected by default when Boot Menu is displayed.",NULL
442
443g_szHelpBootFloppyDrvs: db  "Detecting the correct number of floppy drives might fail when using a floppy controller with its own BIOS."
444                        db  " A minimum number of floppy drives can be specified to force non-detected drives to appear on boot menu.",NULL
445
446g_szHelpSerialDetect:   db  "Set to Yes, at the end of normal drive detection, COM ports 1-7 (in reverse order) will be scanned for a connection"
447                        db  " to a serial drive server. This option provides flexibility with the COM port and baud rate to be used,"
448                        db  " it need not be configured ahead of time, but at the expense of a slower boot process."
449                        db  " Even when this option is set to No, this functionality can still be invoked by holding down the ALT key at the end"
450                        db  " of normal drive detection. Note that if any serial drives are detected during the normal drive detection,"
451                        db  " no scan will take place (to avoid finding the same drive twice).",NULL
452
453g_szMultichoiceBootDispMode:    db  "Default",LF
454                                db  "40x25 Black & White",LF
455                                db  "40x25 Color",LF
456                                db  "80x25 Black & White",LF
457                                db  "80x25 Color",LF
458                                db  "80x25 Monochrome",NULL
459
460g_szValueBootDispModeDefault:   db  "Default",NULL
461g_szValueBootDispModeBW40:      db  "BW40",NULL
462g_szValueBootDispModeCO40:      db  "CO40",NULL
463g_szValueBootDispModeBW80:      db  "BW80",NULL
464g_szValueBootDispModeCO80:      db  "CO80",NULL
465g_szValueBootDispModeMono:      db  "Mono",NULL
466
467g_szMultichoiceBootFloppyDrvs:  db  "Autodetect",LF
468                                db  "1",LF
469                                db  "2",LF
470                                db  "3",LF
471g_szValueBootFloppyDrvs4:       db  "4",NULL
472g_szValueBootFloppyDrvs3:       db  "3",NULL
473g_szValueBootFloppyDrvs2:       db  "2",NULL
474g_szValueBootFloppyDrvs1:       db  "1",NULL
475g_szValueBootFloppyDrvsAuto:    db  "Auto",NULL
476
477
478; Strings for Flash menu
479g_szItemFlashStart:     db  "Start flashing",NULL
480g_szItemFlashEepromType:db  "EEPROM type",NULL
481g_szItemFlashSDP:       db  "SDP command",NULL
482g_szItemFlashAddr:      db  "EEPROM address",NULL
483g_szItemFlashPageSize:  db  "Page size",NULL
484g_szItemFlashChecksum:  db  "Generate checksum byte",NULL
485
486g_szDlgFlashEepromType: db  "Select EEPROM type.",NULL
487g_szDlgFlashSDP:        db  "Select Software Data Protection command.",NULL
488g_szDlgFlashAddr:       db  "Enter segment address where EEPROM is located.",NULL
489g_szDlgFlashPageSize:   db  "Select write page size.",NULL
490g_szDlgFlashChecksum:   db  "Generate checksum byte to the end of BIOS image?",NULL
491
492g_szNfoFlashEepromType: db  "EEPROM type.",NULL
493g_szNfoFlashStart:      db  "Writes BIOS to EEPROM.",NULL
494g_szNfoFlashSDP:        db  "Software Data Protection command.",NULL
495g_szNfoFlashAddr:       db  "Address (segment) where EEPROM is located.",NULL
496g_szNfoFlashPageSize:   db  "Number of bytes to write before delay.",NULL
497g_szNfoFlashChecksum:   db  "Generate checksum byte to the end of BIOS image.",NULL
498
499g_szHelpFlashSDP:       db  "Software Data Protection Command:",LF
500                        db  "None    = Do not use Software Data Protection. Meant for EEPROMs that do not support SDP.",LF,LF
501                        db  "Enable  = Write protects the EEPROM after flashing."
502                        db  " Software Data Protection should always be enabled if EEPROM supports it.",LF,LF
503                        db  "Disable = Disables Software Data Protection after flashing.",NULL
504
505g_szHelpFlashPageSize:  db  "Larger page size will improve write performance but not all EEPROMs support large pages or page writing at all."
506                        db  " Byte writing mode will be used when page size is set to 1. Byte writing mode is supported by all EEPROMs."
507                        db  " Large pages cannot be flashed with slow CPUs.",NULL
508
509g_szHelpFlashChecksum:  db  "PC BIOSes require a checksum byte at the end of expansion card BIOS ROMs."
510                        db  " You might not want to generate checksum byte when flashing some other images than XTIDE Universal BIOS.",NULL
511
512g_szMultichoiceEepromType:
513                        db  "2816 (2 kiB)",LF
514                        db  "2864 (8 kiB)",LF
515                        db  "2864 mod (8 kiB)",LF
516                        db  "28256 (32 kiB)",LF
517                        db  "28512 (64 kiB)",NULL
518g_szValueFlash2816:     db  "2816",NULL
519g_szValueFlash2864:     db  "2864",NULL
520g_szValueFlash2864Mod:  db  "2864mod",NULL
521g_szValueFlash28256:    db  "28256",NULL
522g_szValueFlash28512:    db  "28512",NULL
523
524g_szMultichoiceSdpCommand:
525                        db  "None",LF
526                        db  "Enable",LF
527g_szValueFlashDisable:  db  "Disable",NULL
528g_szValueFlashEnable:   db  "Enable",NULL
529g_szValueFlashNone:     db  "None",NULL
530
531g_szMultichoicePageSize:
532                        db  "1 byte",LF
533                        db  "2 bytes",LF
534                        db  "4 bytes",LF
535                        db  "8 bytes",LF
536                        db  "16 bytes",LF
537                        db  "32 bytes",LF
538g_szValueFlash64bytes:  db  "64 bytes",NULL
539g_szValueFlash32bytes:  db  "32 bytes",NULL
540g_szValueFlash16bytes:  db  "16 bytes",NULL
541g_szValueFlash8bytes:   db  "8 bytes",NULL
542g_szValueFlash4bytes:   db  "4 bytes",NULL
543g_szValueFlash2bytes:   db  "2 bytes",NULL
544g_szValueFlash1byte:    db  "1 byte",NULL
545
546g_szSelectionTimeout:   db  DOUBLE_BOTTOM_LEFT_CORNER,DOUBLE_LEFT_HORIZONTAL_TO_SINGLE_VERTICAL,"%ASelection in %2u s",NULL
547g_szDashForZero:        db  "- ",NULL
548g_szValueUnknownError:  db  "Error!",NULL
549
Note: See TracBrowser for help on using the repository browser.